Toshiba Satellite Pro Te2000 Manual

							  3-9
GETTING
 S
TARTED
2. Make sure all disk activity has stopped, then remove any CDs or diskette.
CAUTION: Make sure the Disk, Slim Select Bay and Slim Select Bay’s
module indicators are off. If you turn off the power while a disk is being
accessed, you can lose data or damage the disk.
3. If you are using Windows XP, click start then click Turn off computer.
From the  Turn off computer menu select Turn off.
If you are using Windows 2000/98, click Start and click Shut Down. From
the Shut Down menu select Shut Down.
4. Turn off the power to any peripheral devices.
CAUTION: Do not turn the computer or devices back on immediately.
Wait a moment to let all capacitors fully discharge.
Hibernation mode
The hibernation feature saves the contents of memory to the hard disk when the
computer is turned off. The next time the computer is turned on, the previous state
is restored. The hibernation feature does not save the status of peripheral devices.
CAUTIONS:1. While entering hibernation mode, the computer saves
the contents of memory to the HDD. Data will be lost if
you remove the battery or disconnect the AC adaptor
before the save is completed. Wait for the Disk
indicator to go out.
2. Do not install or remove a memory module while the
computer is in hibernation mode. Data will be lost.
Benefits of hibernation
The  hibernation feature provides the following benefits:
❑ ❑❑ ❑
❑Saves data to the hard disk when the computer automatically shuts down
because of a low battery.
NOTE: For the computer to shut down in hibernation mode, the hibernation
feature must be enabled in two places in TOSHIBA Power Saver: the
Hibernate window and the Battery Alarm item of the Alarm window.
Otherwise, the computer will shut down in Standby mode. If battery power
becomes depleted, data saved in Standby will be lost. 
						

							3-10
Users Manual
GETTING
 S
TARTED
❑ ❑❑ ❑
❑You can return to your previous working environment immediately when
you turn on the computer.
❑ ❑❑ ❑
❑Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System hibernate
feature.
❑ ❑❑ ❑
❑You can use the panel power off feature.
Starting Hibernation
To enter Hibernation mode, follow the steps below.
Windows XP
1. Click Start.
2. Select Turn Off Computer.
3. Open the Turn Off Computer dialog box. Hibernate is not displayed.
4. Press the Shift key. The Standby item will change to Hibernate.
5. Select Hibernate.
Windows 2000
1. Click  Start and click Shut Down.
2. In Shut Down Windows select Hibernate and click the OK button.
Windows 98
1. Open the Start menu.
2. Select Hibernate.
Automatic Hibernation
The computer will enter Hibernate mode automatically when you press the
power button or close the lid. First, however, make the appropriate settings
according to the steps below.
1. Open the Control Panel.
2. a. In Windows XP, open Performance and Maintenance and open
TOSHIBA Power Saver.
b. In Windows 2000/98, double-click the TOSHIBA Power Saver icon.
3. Select the Hibernate window, select the Enable Hibernate support check box
and click the Apply button. 
						

							  3-11
GETTING
 S
TARTED
4. Select the Power Save Modes window.
5. Double-click Power Mode (Full Power, Normal, etc.) and open the System
Power Mode window.
6. Enable the desired Hibernation settings for When I press the power button
and When I close the lid.
7. Click the OK button.
Data save in hibernation mode
When you turn off the power in hibernation mode, the computer takes a
moment to save current memory data to the hard disk. During this time, the
Built-in HDD indicator will light.
After you turn off the computer and memory is saved to the hard disk, turn off
the power to any peripheral devices.
CAUTION: Do not turn the computer or devices back on immediately.
Wait a moment to let all capacitors fully discharge.
Standby mode
In standby mode the power remains on, but the CPU and all other devices are
in sleep mode.
CAUTIONS:1. Before entering Standby mode, be sure to save your data.
2. Do not install or remove a memory module while the
computer is in standby mode. The computer or the
module could be damaged.
3. Do not remove the battery pack while the computer is in
standby mode (unless the computer is connected to an AC
power source). Data in memory will be lost.
4. If you carry the computer on board an aircraft or into a
hospital, be sure to shut down the computer in hiberna-
tion mode or in shutdown mode to avoid radio signal
interference.
Benefits of standby
The  standby feature provides the following benefits: 
						

							3-12
Users Manual
GETTING
 S
TARTED
❑ ❑❑ ❑
❑Restores the previous working environment more rapidly than does
hibernation.
❑ ❑❑ ❑
❑Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System Standby
feature.
❑ ❑❑ ❑
❑You can use the panel power off feature.
Executing standby
You can enter standby mode in one of three ways:
1. In Windows XP, click Start, click Turn Off Computer and click Stand by.
In Windows 2000/98, click Start, click Shut Down, select Stand by and click
OK.
2. Close the display panel. This feature must be enabled. Refer to the System
Power Mode item in Power Saver Utility described in the Control Panel
and double-click the TOSHIBA Power Saver icon.
3.  Press the power button. This feature must be enabled. Refer to the
System Power Mode item in Power Saver Utility described in the Control
Panel and double-click the TOSHIBA Power Saver icon.
When you turn the power back on, you can continue where you left when you
shut down the computer.
NOTES:1. When the computer is shut down in standby mode, the
power indicator glows orange.
2. If you are operating the computer on battery power, you
can lengthen the operating time by shutting down in
hibernation mode. Standby mode consumes more power.
Standby limitations
Standby will not function under the following conditions:
❑ ❑❑ ❑
❑Power is turned back on immediately after shutting down.
❑ ❑❑ ❑
❑Memory circuits are exposed to static electricity or electrical noise.
Restarting the computer
Certain conditions require that you restart the computer system. For example,
if: 
						

							  3-13
GETTING
 S
TARTED
❑ ❑❑ ❑
❑You change certain computer settings.
❑ ❑❑ ❑
❑An error occurs and the computer does not respond to your keyboard
commands.
There are three ways to restart the computer system:
1. If you are using Windows XP, click start then click Turn off computer.
From the  Turn off computer menu select Restart.
If you are using Windows 2000/98, click Start and click Shut Down. From
the Shut Down menu select Restart.
2. If the computer is already on, press Ctrl + Alt + Del (Windows 98 only).
3. Press the power button and hold it down for five seconds. Wait 10 to 15
seconds, then turn the power on again by pressing the power button.
Restoring the Windows system
If preinstalled files are damaged, use the Product Recovery CD-ROM to
restore them. To restore the operating system and all preinstalled software,
follow the steps below.
CAUTION: When you reinstall the Windows operating system, the hard
disk will be reformatted and all data will be lost.
1. Load the Product Recovery CD-ROM in the drive and turn off the computer’s
power.
2. Hold down the C key and turn on the power. When In Touch with
Tomorrow TOSHIBA appears, release the C key.
NOTE: When you install additional software components, a window 
						

							3-14
Users Manual
GETTING
 S
TARTED
similar to the one below will be shown while the software is being
decompressed. Leave it until it disappears. Do not click Cancel.
Figure 3-6  Software decompression window
3. Follow the on-screen instructions. 
						

							  3-15
GETTING
 S
TARTED 
						

							OPERATING
 B
ASICS
 4-1
Chapter 4
Operating Basics
This chapter gives information on basic operations including using the AccuPoint
II, optical media drives, the external diskette drive, the internal modem, the LAN
and changing Slim Select Bay modules. It also provides tips on caring for your
computer and heat dispersal.
Using AccuPoint II
To use the AccuPoint II, simply push it with your finger tip in the direction you
want to move the on-screen pointer.
Figure 4-1 AccuPoint II and control buttons
Two large buttons below the keyboard are used like the buttons on a mouse pointer.
Press a button to select a menu item or to manipulate text or graphics designated by
the pointer. The left small button toggles Universal Scroll on and off. When
Universal Scroll is on, use the AccuPoint to scroll the screen. The right small button
works as the Back button on your Internet browser. You can switch the functions
of the large and small buttons in the Mouse utility in Windows Control Panel.
ACCUPOINT II
CONTROL BUTTONS
ACCUPOINT II 
						

							Users Manual
OPERATING
 B
ASICS
4-2
AccuPoint II precautions
Certain conditions can affect the on-screen pointer when using AccuPoint II. For
example, the pointer may travel contrary to AccuPoint II operation or an error
message may appear, if
❑You touch the AccuPoint II during power-up.
❑You apply constant, soft pressure during power-up.
❑There is a sudden temperature change.
❑Strong stress is applied to the AccuPoint II.
If an error message appears, reboot the computer. If an error message does not
appear, wait a moment for the pointer to stop, then continue operation.
Replacing the cap
The AccuPoint II cap is an expendable item that should be replaced after prolonged
use. This is one spare AccuPoint II cap supplied with the computer.
1. To remove the AccuPoint II cap, firmly grasp the cap and pull it straight up.
Figure 4-2 Removing the AccuPoint II cap
2. Position a new cap on the peg and press it into place.
NOTE: The peg is square, so be careful to align the cap’s square hole
with the peg.A
CCUPOINT II CAP
PEG 
						

							OPERATING
 B
ASICS
 4-3
Changing Slim Select Bay modules
This section explains how to change modules in the Slim Select Bay. The illustra-
tions show replacement of the DVD-ROM drive with the Slim Select Bay HDD
adaptor. Therefore, the text refers to those modules. However, the procedures are
the same for any of the modules: DVD-ROM drive, CD-ROM drive, CD-R/RW
drive, CD-RW/DVD-ROM drive or optional Slim Select Bay 2nd battery pack with
separate tray.
CAUTION: To avoid injury, do not put your hand into the Slim Select
Bay slot.
Removing a module
Remove the DVD-ROM drive as described below.
1. Check all disk indicators to make sure no disks are operating.
2. Turn the computer upside down.
CAUTION: Wait for all disk indicators to go out before you turn over the
computer and be careful to lay the computer down gently. Shock can
damage the HDD or other components.
3. Be sure the screw of the Slim Select Bay lock is set in the front hole,which is
the unlock position.
4. Slide the Slim Select Bay latch to the unlock position.
5. Grasp the DVD-ROM drive and slide it out.
CAUTION: The DVD-ROM drive and other Slim Select Bay modules can
become hot with use. Be careful when removing the module.
Figure 4-3  Removing the DVD-ROM drive
Changing Slim Select Bay modules
SLIM SELECT
BAY MODULE
SLIM SELECT
BAY LATCH