Home > Toshiba > Video Recorder > Toshiba Dvr610 User Manual

Toshiba Dvr610 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Toshiba Dvr610 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Downloaded from www.Manualslib.com manuals search engine 41EN41EN
    Disc 
    Management
    Recording
    Playback
    Introduction
    Connections
    Basic Setup
    Editing
    Function Setup
    VCR Function
    Others
    TIMER RECORDING
    Hints for Timer Recording
    PROG. A
    PROG. B
    actual
    recording PROG. A
    PROG. B
    When the starting time is the same:
    A program set previously (PROG. A) has priority.
    The first 2 minutes (at the longest) will be cut off.
    PROG. A
    PROG. B
    actual
    recording PROG. A
    PROG. APROG. CPROG. B
    PROG. C
    When the starting time and the ending time
    for each programs are different:
    A program that has earlier start time has priority.
    The first 2 minutes (at the longest) will be cut off.
    PROG. A
    PROG. B
    actual
    recording PROG.B
    PROG.A
    When the recording time is partially overlapped:
    PROG. A will start after PROG. B is complete to
    be recorded. 
    The first 2 minutes (at the longest) will be cut off.
    PROG. A
    PROG. B
    actual
    recording PROG. B
    When the recording time is entirely overlapped:
    PROG.A will not be recorded. 
    This unit records the programs according to priority if the timer progra\
    mmings are overlapped. The timer 
    programming set previously has priority.
    A timer recording of lower priority will be canceled or start from the m\
    iddle. 
    Check the overlapped timer programmings and change the priority if neces\
    sary. •  If there is a power failure or this unit has been 
    unplugged for more than 30 seconds, the clock setting 
    and all timer programming will be lost.
    •  If a disc is not inserted or if a inserted disc is not  recordable (finalized DVD-RW/-R, finalized DVD+RW, a 
    fully recorded disc, etc.), “DVD” on the front panel 
    display flashes and timer recording cannot be 
    performed. In some cases, 
     will appear momentarily 
    around the start point as the unit attempts to record. 
    Please insert a recordable disc.
    •  If a cassette tape with an erase-protection tab is not in  the cassette compartment or there is no cassette tape in 
    the cassette compartment, “VCR” on the front panel 
    display flashes and timer recording cannot be 
    performed. Please insert a recordable cassette tape.
    •  If you press [TIMER SET] and turn on the unit while  either DVD or VCR is in timer standby mode, 
     
    disappears. In this case, you cannot change the mode 
    between DVD and VCR. You cannot change any settings 
    using  [SETUP] or edit discs.
    •  When all the timer recording is completed,  flashes. To 
    play back or eject the recorded disc, press  [I/
    y ON/STANDBY] first, then select the recorded title and 
    press  [PLAY  B], or [OPEN/CLOSE  A] to remove the disc.
    •  During timer recording or timer standby mode ( will 
    appear), any operations on the unit will not be available. 
    To make these operations available, press [C STOP] on 
    the front panel to cancel the timer recording or [TIMER 
    SET] to release timer standby mode (
      will disappear).
    •  To cancel the timer standby mode, press [TIMER SET].
    •  When the starting and the ending time are the same,  “Exceeds 12 hours” appears and the program setting will 
    not be accepted.
    •  When the programmed starting and ending time are  earlier than the current time, the setting will not be 
    accepted.
    •  If the starting time is earlier and the ending time is later  than the current time, the recording will start right after 
    you turn the power off.
    •  The timer recording cannot be performed in DVD and  VCR at the same time. If you set 2 programming with the 
    same channel and time in both devices, the program 
    with a lower program number will be recorded.
    The Priority of Overlapped Settings
    Note for DVD recording
    •  When the recording time of 2 programs are overlapped, or 
    the end time of a program and the start time of another 
    program is the same, the first 2 minutes (at the longest) of 
    the subsequent program will be cut off.
    •  If the cut-off portion comes up to 3 minutes or more, this  program will be displayed with errors number E40 in the 
    timer programming list.
    PROG. A
    PROG. B
    actual
    recording
    The first 2 minutes (at the longest) will be cut off. PROG. B
    PROG. A
    When the end time of the programming
    currently being recorded and the start time
    of the subsequent program are same:
    The beginning of the PROG. B may be cut off. 
      
     
    E9KGAUD_D-VR610KU_EN.indd   41 E9KGAUD_D-VR610KU_EN.indd   41 2007/12/18   17:10:15
    2007/12/18   17:10:15  
    						
    							Downloaded from www.Manualslib.com manuals search engine 42 EN42 EN
    SATELLITE LINK
    You can set the unit to start recording whenever it 
    detects the video signal from the external tuner.
    Preparing for the satellite link timer recording:
    Preparation on the tuner
    •  The external tuner should be equipped with some kind of timer function. Using timer function of the tuner, set 
    it to output audio/video signals when it comes to the 
    time you want to start recording, and stop output audio/
    video signals when it comes to the time you want to 
    finish recording. Refer to the tuner’s manual on how to 
    set the timer.
    •  Make sure to set the satellite link standby mode when  you finish setting.
    Preparation on this unit
    •  You must let the unit know which video input jack you  are using before making a recording.
    Refer to “SETTINGS FOR THE VIDEO INPUT” on page 20.
    1
      Press [SAT. LINK].
    2
     Use [K / L] to select the time, media 
    and recording mode, then press 
    [ENTER].
    Satellite Link
    To Standby Mode
     12:00AM DVD XP Start
    Mode
    DVD
    VCR
    3
     Use [K / L] or [the Number buttons] 
    to set the desired starting time, then 
    press [
    B].
    •  The hour can be selected from 1 to 12 with AM  or PM.
    •  Repeat procedures in this step to set the  desired minutes.
    •  If you wish to go back to the left, press  [{].
    4
     Use [K / L] to select a recording 
    media (“DVD” or “VCR”), then press 
    [
    B].
    5
     Use [K / L] to select the recording mode.
    Refer to “Recording Mode” on page 33 for DVD 
    or “Recording” on page 99 for VCR.
    SE-R0295
    OPEN/
    CLOSE INPUT
    SELECT HDMI
    .@/: ABC GHI
    PQRS TUV
    SPACE
    SETUP DISPLAY AUDIO TIMER
    PROG.
    DISC MENU
    CLEAR RETURN
    TOP MENU
    WXYZ
    SAT.LINK
    JKL MNO
    DEFTRACKING
    ENTER
    INSTANT
    SKIP
    PLAY
    DVD
    VCR
    PAU S E REV
    SKIP
    STOPSKIP
    FWD
    1.3x/0.8x
    PLAYTIME SLIP
    TIMER SET ZOOM
    SEARCH
    REPEAT REC
    REC MODE
    DUBBING
    ENTER
    STOP
    TIMER
    PROG.
    SAT.LINK
    TIMER SET
    E9KGAUD_D-VR610KU_EN.indd   42 E9KGAUD_D-VR610KU_EN.indd   42 2007/12/18   17:10:16
    2007/12/18   17:10:16  
    						
    							Downloaded from www.Manualslib.com manuals search engine 43EN43EN
    Disc 
    Management
    Recording
    Playback
    Introduction
    Connections
    Basic Setup
    Editing
    Function Setup
    VCR Function
    Others
    SATELLITE LINK
    6
     Press [ENTER].
    “To Standby Mode” is highlighted.
    7
      Press [ENTER] again.
    Satellite Link
    To Standby Mode
     12:00AM DVD XP Start
    Mode
    DVD
    VCR
    In a second, the unit will be turned off 
    automatically as it goes into the satellite link 
    standby mode.
    To cancel the satellite link function while in 
    the satellite link standby mode:
    Press [TIMER SET] to turn on the unit.
    To cancel the satellite link function while the 
    satellite link recording is in progress:
    Press  [C STOP] or [A EJECT / C STOP] on the 
    front panel of the unit.
    Note
    •  If the signal of external input breaks up over 5 seconds, satellite link\
     function will be canceled.
    •  If you have not set the clock, “Clock Setting” menu will appear at\
     step 1. Follow to step 3 in “Clock Setting” on  page 26.
    •  You cannot set the end time for the satellite link timer recording on th\
    is unit.
    •  Recording picture will be distorted if the copy protection signal is bei\
    ng detected during satellite link timer  recording.
    •  You can record the satellite link by using S-video input jacks on the re\
    ar panel. Refer to page 19 for more  information.
    • Press  [TIMER PROG.] during the satellite link timer recording to check the satellite link t\
    imer recording in 
    progress.
    •  When a regular timer recording and the satellite link timer recording ar\
    e overlapped, those recordings are  recorded as illustrated below.
    example 2
    actual
    recordingtimer
    recording
    satellite link
    example 3
    actual
    recording timer
    recording
    satellite link
    The first 2 minutes (at the longest) will be cut off.
    example 1
    timer
    recording
    actual
    recording satellite link
    The first 2 minutes (at the longest) will be cut off.
    E9KGAUD_D-VR610KU_EN.indd   43 E9KGAUD_D-VR610KU_EN.indd   43 2007/12/18   17:10:17
    2007/12/18   17:10:17  
    						
    							Downloaded from www.Manualslib.com manuals search engine 44 EN44 EN
    SETTINGS FOR AN EXTERNAL DEVICE
    DVDDIGITAL
    AUDIO OUT AUDIO
    OUT S-VIDEO
    IN
    COAXIAL L
    R L
    R L
    R
    S -VI DEO I N  --- AU D I O --- OU T
    I N  --- V I D E O --- OU TCOMPONENTVIDEO OUTDVD/VCRHDMI OUT
    IN L
    R L
    R
    S-VIDEO IN --- AUDIO
     --- OU T
    IN --- VIDEO  --- OU T
    DVD/VCR
    AUDIO OUT DV-OUT
    LRVIDEO OUTAUDIO OUT
    L
    RVIDEO
    OUT
    S-VIDEO
    OUT
    VIDEO L R DV
    front of this unit rear of this unit
    external device(camcorder, VCR etc.)
    DV cable
    (4-pin)
    RCA
    video
    cable RCA
    audio
    cable
    to L2 & L3
    or
    to L1
    S-video
    cable RCA
    video
    cableRCA
    audio cableor
    L2L3
    L1
    or
    Supplied cables used in this connection are as follows:
    • RCA audio cable (L/R) x 1
    • RCA video cable x 1
    Please purchase the rest of the necessary cables at your local store.
    Connect the external device properly to the unit by using input jacks ei\
    ther L2 (Front) or L1 (Rear).
    When connecting an external device of monaural output to this unit, use \
    AUDIO L jack of L2 (Front).
    Use S-video or the RCA audio/video cables for this connection.
    When connecting a DVC (digital video camcorder), use the DV input jack\
     on the front panel instead of VIDEO IN jack.
    Connection to an External Device
    E9KGAUD_D-VR610KU_EN.indd   44 E9KGAUD_D-VR610KU_EN.indd   44
    2007/12/18   17:10:18
    2007/12/18   17:10:18  
    						
    							Downloaded from www.Manualslib.com manuals search engine 45EN45EN
    Disc 
    Management
    Recording
    Playback
    Introduction
    Connections
    Basic Setup
    Editing
    Function Setup
    VCR Function
    Others
    SETTINGS FOR AN EXTERNAL DEVICE
    Recording from an External Device
    1
      Turn on the TV and press 
    [I/
    yy ON/STANDBY], and be sure to 
    select the input of the TV to which 
    the unit is connected.
    2
      When you want to record to the disc:  Press [DVD].
    Press [OPEN/CLOSE A ] to open the disc 
    tray. Place the disc to record properly.
    Press [OPEN/CLOSE A] again to close 
    the disc tray.
    It takes a while to load 
    the disc.
    When you want to record to a 
    cassette tape:
    Press [VCR].
    Insert the cassette tape with an 
    erase-protection tab into the cassette 
    compartment.
    3
      Select the input of the unit which the external device is connected. (L1, L2 
    or DV(L3))
    •  To use the input jacks on the rear of this unit;  Select “L1” by using [INPUT SELECT  ].
    •  To use the input jacks on the front of this unit;  Select “L2” or “DV“ (L3) by using 
    [INPUT SELECT 
     ].
    4
      Press [REC MODE] to select a 
    recording mode.
    Refer to “Recording Mode” on page 33 for DVD 
    or “Recording” on page 99 for VCR.
    5
     Press [I REC] on the unit to start recording.
    6
      Start playback on the external device to record from.
    7
     Press [C  STOP] / [A  EJECT / C STOP] 
    on the unit to stop recording.
    This operation may take 
    awhile to be completed.
    Before recording from an external device, refer to the 
    instructions for the connection on page 44.
         
    2
    177
    5
    5
    OPEN/
    CLOSE INPUT
    SELECT HDMI
    .@/: ABC GHI
    PQRS TUV
    SPACE
    SETUP DISPLAY AUDIO TIMER
    PROG.
    DISC MENU
    CLEAR RETURN
    TOP MENU
    WXYZ
    SAT.LINK
    JKL MNO
    DEFTRACKING
    ENTER
    INSTANT
    SKIP
    PLAY
    DVD
    VCR
    PAU S E REV
    SKIP
    STOPSKIP
    FWD
    1.3x/0.8x
    PLAYTIME SLIP
    TIMER SET ZOOM
    SEARCH
    REPEAT REC
    REC MODE
    DUBBING
    INPUT
    SELECTOPEN/
    CLOSE
    RECREC MODE
    STOP
    DVDVCR
    E9KGAUD_D-VR610KU_EN.indd   45 E9KGAUD_D-VR610KU_EN.indd   45 2007/12/18   17:10:18
    2007/12/18   17:10:18  
    						
    							Downloaded from www.Manualslib.com manuals search engine 46 EN46 EN
    DV DUBBING
    Guide to DV and On-Screen Display
    This function helps you to easily dub the contents of the DVC (digital \
    video camcorder) to this unit.
    You can control basic operations of the DVC from the remote control of t\
    his unit such as playback, fast forward or 
    reverse and stop all operations if the DVC is in video mode. Use the DV \
    cable that has 4-pin input jack and is 
    compliance with the IEEE1394 standards. When you connect to DV input jac\
    k on the front of this unit, select “DV” 
    position by using [INPUT SELECT 
     ] on the remote control and press [DISPLAY] to show the DV dubbing 
    information for the operation of your DVC.
    DV
    AB-1234 0:12:34
    1/   1 1/   1
    SP 1:00
    -RWVRORGControl DVD
    DV Audio  Stereo1
    Start RecDV
    AB-1234 0:12:34
    1/   1 1/   1
    SP 1:00
    -RWVRORG
    2
    3
    1
    4
    5
    76
    The menu changes according to  what mode of DVC.
    Switch the mode on the DVC to 
    playback mode for the dubbing  information.
    When the DVC is 
    in video mode... When the DVC is not 
    in camera mode...
    1. DV  icon
    2. Indicator of active device
      •  When the “Control” is 
    highlighted, press [ENTER] to 
    display the item selection. Use 
    [K / L]  to select the device you 
    wish to operate, then press 
    [ENTER] to activate.
      •  Select “DVD” to control this unit.
      •  Select “DVC” to control your DVC.
    3. Recording  audio  mode
      •  Other than the DVC is in stop  mode, the “DV Audio” can be 
    selected. Press [ENTER] to display 
    the item selection and then use 
    [K / L] to select the audio you 
    wish to output. Press [ENTER] 
    again to activate.
      •  Select “Stereo1” to dub the stereo  sound.
      •  Select “Stereo2” to dub the sound  with after recording sound.
      •  Select “Mix” to dub the stereo1  and stereo2.
    4. Indicator of dubbing function
      •  When the unit is ready for  dubbing, “Start Rec” will appear.
      •  When the unit is in dubbing,  “Pause Rec” will appear.
    5. Channel  position
      •  When you select “DV” by using  [INPUT SELECT 
    ], “DV” will 
    appear. 6. Product name of your DVC
      •  If the unit cannot recognize the 
    input signal from the DVC or the 
    unknown product, “No Device” or 
    “****” will appear instead.
    7. Status of the current operation  and the time counter
      Each icon means (Available icons  may vary depending on the DVC):
      DVC is in stop mode.
      DVC is in playback mode.
      DVC is in pause mode.
       DVC is fast forwarding. (standard speed)
       DVC is fast forwarding. (faster than above)
       DVC is fast forwarding. (faster than above)
       DVC is slow forwarding. (standard speed)
       DVC is slow forwarding. (faster than above)
       DVC is slow forwarding. (faster than above)
       DVC is fast forwarding. (in stop mode)
       DVC is fast reversing. (in stop mode)
       DVC is fast reversing. (standard speed)
       DVC is fast reversing. (faster than above)
       DVC is fast reversing. (faster than above)
       DVC is in slow reverse playback.
      DVC is in recording.
       DVC is in recording pause mode.
    The following instructions are described with the operations using the remote control of this unit.
    DVD mode
    VCR mode
    You cannot control the DVC in VCR mode. For dubbing onto VCR, refer to p\
    age 48.
    E9KGAUD_D-VR610KU_EN.indd   46 E9KGAUD_D-VR610KU_EN.indd   46 2007/12/18   17:10:20
    2007/12/18   17:10:20  
    						
    							Downloaded from www.Manualslib.com manuals search engine 47EN47EN
    Disc 
    Management
    Recording
    Playback
    Introduction
    Connections
    Basic Setup
    Editing
    Function Setup
    VCR Function
    Others
    DV DUBBING
    DVC to DVD Dubbing
    Before recording from DVC, see page 44 for connection 
    instructions.
        
    2
      Press [REC MODE] to select a 
    recording mode.
    (Refer to “Recording Mode” on page 33 for DVD 
    or “Recording” on page 99 for VCR.)
    3
     Press [DISPLAY].
    4
      With “Control” highlighted, press [ENTER] to display the available 
    devices to control with the remote 
    control of this unit. Use [K / L] to 
    select “DVC”, then press [ENTER].
    DV
    AB-1234 0:12:34
    1/   1 1/   1
    XP 1:00
    -RWVRORGControl DVD
    DV Audio  Stereo1
    Start Rec
    Now you can operate your DVC with the remote 
    control of this unit.
    5
     Press [PLAY  B] to start playing back 
    the DVC, and find where you wish to 
    start dubbing. 
    Then, press [STOP C] when you come 
    to the desired start point.
    6
     Use [K / L] to select “Start Rec”, then  press [ENTER].
    The dubbing will start.
    7
      To stop dubbing;Use [K / L] to select “Control”, then 
    press [ENTER].
    Use [K / L] to select “DVD”, then 
    press [ENTER].
    Then press [STOP C].
    Press [DVD] first.
     
    Preparing for DV to DVD dubbing:
    •  Insert a recordable disc and make sure your DVC is in 
    video mode.
    1
      Use [INPUT SELECT ] to select “DV”.
    AB- 1234
    0:00:00DV
    SE-R0295
    OPEN/
    CLOSE INPUT
    SELECT HDMI
    .@/: ABC GHI
    PQRS TUV
    SPACE
    SETUP DISPLAY AUDIO TIMER
    PROG.
    DISC MENU
    CLEAR RETURN
    TOP MENU
    WXYZ
    SAT.LINK
    JKL MNO
    DEFTRACKING
    ENTER
    INSTANT
    SKIP
    PLAY
    DVD
    VCR
    PAU S E REV
    SKIP
    STOPSKIP
    FWD
    1.3x/0.8x
    PLAYTIME SLIP
    TIMER SET ZOOM
    SEARCH
    REPEAT REC
    REC MODE
    DUBBING
    DISPLAY
    ENTER
    INPUT
    SELECT
    PLAY
    REC MODE
    STOP
    DVD
    E9KGAUD_D-VR610KU_EN.indd   47 E9KGAUD_D-VR610KU_EN.indd   47 2007/12/18   17:10:22
    2007/12/18   17:10:22  
    						
    							Downloaded from www.Manualslib.com manuals search engine 48 EN48 EN
    DV DUBBING
    Note for DV dubbing
    •  If you press [PAUSE F] at step 5 in “DVC to DVD Dubbing” on page 47, the tape will rewin\
    d to the point a few 
    seconds preceding the paused point. When you press [ENTER] at step 6 in “DVC to DVD Dubbing” on page 47, 
    then, it will start dubbing when it comes to the paused point.
    •  The unit does not send out the output signal to DVC.
    •  For the proper operation, connect DVC to the unit directly. Do not conne\
    ct this unit and DVC via any other unit.
    •  Do not connect more than 1 DVC.
    •  The unit can only accept DVC. Other DV device such as cable/satellite bo\
    x or D-VHS VCR cannot be recognized.
    •  If no video signal is detected from the DVC during DVC to DVD dubbing, t\
    he recording will be paused and “ I” will 
    flash on the TV screen. The recording will resume when the unit detects \
    the video signal again.
    •  When the DVC is in camera mode, refer to “Guide to DV and On-Screen D\
    isplay” on page 46.
    •  You cannot dub from DVC during timer standby mode.
    •  You cannot dub from DVC to the both DVD and VCR at the same time.
    •  You cannot change the output mode during DVC to VCR dubbing. If you want\
     to switch to the DVD mode, stop  the VCR first.
    •  During DVC to VCR dubbing, you cannot change channels while paused.
    •  When output is in DVD mode while playing back a DVD using DV(L3), you \
    cannot switch to the VCR mode.
    •  If you are using anything other than DV(L3) to playback DVD, you can s\
    witch to the VCR mode, but cannot select  DV(L3) channel. (You can select DV(L3) after switching to the DVD m\
    ode during VCR playback.)
    •  During timer standby of either component, you cannot select DV(L3) eve\
    n on the component which is not in timer  standby.
    •  Date / time and cassette memory data will not be recorded.
    •  Pictures with a copy-guard signal cannot be recorded.
    •  A DV terminal is a terminal that can use the transmission mode conformin\
    g to the IEEE 1394 standards called “Fire  Wire”. It serves as the interface that connects the PC and peripheral\
     device such as “i.Link” (registered trademark of 
    SONY). It enables digital dubbing between DV devices with little degrad\
    ation.
    DVC to VCR Dubbing
    Before recording from DVC, refer to page 44 for 
    connection instructions.
    1
      Repeat the steps 1 and 2 on page 47.
    2
      Press the PLAY button on your DVC 
    to find where you wish to start 
    dubbing. Then, press the PAUSE 
    button on the DV camcorder when 
    you come to the desired start point.
    3
     Press [REC  I] to start recording.
    4
      Press the PLAY button or the PAUSE 
    button on your DVC to resume the 
    playback.
    The dubbing will start.
    To pause the recording:
    Press  [PAUSE  F] once.
    “REC” will flash.
    To resume recording:
    Press  [REC I] or press [PAUSE  F] again.
     “REC” will reappear.
    5
      To stop recording, press [STOP C].
    Press [VCR] first.
     
    Preparing for DV to VCR dubbing:
    •  Insert a recordable cassette tape and make sure your 
    DVC is in video mode.
    SE-R0295
    DISC MENU
    CLEAR RETURN
    TOP MENU
    ENTER
    INSTANT
    SKIP
    PLAY
    DVD
    VCR
    PAU S E REV
    SKIP
    STOPSKIP
    FWD
    1.3x/0.8x
    PLAYTIME SLIP
    TIMER SET ZOOM
    SEARCH
    REPEAT REC
    REC MODE
    DUBBING
    ENTER
    PAUSE
    REC
    STOP
    VCR
    E9KGAUD_D-VR610KU_EN.indd   48 E9KGAUD_D-VR610KU_EN.indd   48 2007/12/19   11:13:25
    2007/12/19   11:13:25  
    						
    							Downloaded from www.Manualslib.com manuals search engine 49EN49EN
    Disc 
    Management
    Recording
    Playback
    Introduction
    Connections
    Basic Setup
    Editing
    Function Setup
    VCR Function
    Others
    DVD/VCR DUBBING
         
    1
      Press [SETUP] and use [K / L] to 
    select “General Setting”, then press 
    [ENTER].
    “General Setting” menu will appear.
    2
     Use [K / L] to select “Recording”, then press [ENTER].
    “Recording” menu will appear.
    3
     Use [K / L] to select “Dubbing Mode”, then press [ENTER].
    Selection menu will appear.
    You can copy a DVD to a cassette tape or copy a cassette 
    tape to a DVD. This function will be possible only if the 
    DVD or the cassette tape is not copy protected.
    Before starting this function, prepare for the recording on 
    the DVD-RW/-R or the cassette tape. Refer to pages 33 
    and 99.
    Make sure:
    •  Insert a recordable disc and a cassette tape with an 
    erase-protection tab.
    Note for recording to a cassette tape:
    •  The cassette tape's erase-protection tab is intact.
    •  The remaining time of the cassette tape is long enough.
    Note for recording to a disc:
    •  Make sure that the disc is recordable. Refer to page 9.
    SE-R0295
    OPEN/
    CLOSE INPUT
    SELECT HDMI
    .@/: ABC GHI
    PQRS TUV
    SPACE
    SETUP DISPLAY AUDIO TIMER
    PROG.
    DISC MENU
    CLEAR RETURN
    TOP MENU
    WXYZ
    SAT.LINK
    JKL MNO
    DEFTRACKING
    ENTER
    INSTANT
    SKIP
    PLAY
    DVD
    VCR
    PAU S E REV
    SKIP
    STOPSKIP
    FWD
    1.3x/0.8x
    PLAYTIME SLIP
    TIMER SET ZOOM
    SEARCH
    REPEAT REC
    REC MODE
    DUBBING
    ENTER
    PAUSE
    PLAY
    SETUP
    STOP
    TOP MENU
    DUBBING
    DVDVCR
    Instructions continue on the next page.
    E9KGAUD_D-VR610KU_EN.indd   49 E9KGAUD_D-VR610KU_EN.indd   49 2007/12/18   17:10:25
    2007/12/18   17:10:25  
    						
    							Downloaded from www.Manualslib.com manuals search engine 50 EN50 EN
    4
     Use [K / L] to select “VCR  DVD”, 
    then press [ENTER].
    General Setting
    Playback
    Display
    Video
    Recording
    Clock
    DivX
    HDMI
    Reset All Auto Chapter
    Recording Audio Select (XP)Auto FinalizeAspect Ratio (Video mode)
    Dubbing Mode
    Make Recording Compatible
    Dubbing ModeVCR       DVD
    DVD       VCR
    5
      Press [SETUP] to exit.
    Press [VCR].
    6
     Press [PLAY  B]. Then press 
    [PAUSE  F] at the point you wish to 
    start recording.
    •  Since it takes about a few seconds before the  actual dubbing begins, please allow extra 5 
    seconds when selecting the starting point.
    7
     Press [DVD].
    Make sure to select a recording speed using 
    [REC MODE].
    8
     Press [DUBBING].
    VCR to DVD duplication will start.
    9
     Press [STOP  C] to stop the recording.
    Title list will automatically appear.
    •  If you want to watch the duplicated material 
    after the VCR to DVD duplication, press [TOP 
    MENU] first then press [ENTER] twice.
    DVD/VCR DUBBING
    4
     Use [K / L] to select “DVD  VCR”, 
    then press [ENTER].
    General Setting
    Playback
    Display
    Video
    Recording
    Clock
    DivX
    HDMI
    Reset All Auto Chapter
    Recording Audio Select (XP)Auto FinalizeAspect Ratio (Video mode)
    Dubbing Mode
    Make Recording Compatible
    Dubbing ModeVCR       DVD
    DVD       VCR
    5
      Press [SETUP] to exit.
    Press [DVD].
    6
     Press [PLAY  B]. Then press 
    [PAUSE  F] at the point you wish to 
    start recording.
    7
      Press [VCR].
    Make sure to select a recording speed using 
    [REC MODE].
    8
     Press [DUBBING].
    DVD to VCR duplication will start.
    9
     Press [STOP  C] to stop the recording.
    VCR to DVDDVD to VCR
    Note
    •  You cannot change the output mode during VCR to DVD or DVD to VCR duplic\
    ation.
    For CD to VCR duplication:
    •  This function is available on Audio CD, not MP3, WMA nor DivX files.
    For VCR to DVD duplication:
    •  After starting VCR to DVD duplication, the picture may be distorted beca\
    use of the auto tracking function.
      This is not a malfunction. Be advised to playback the cassette tape unti\
    l the picture is stabilized, then set the 
    starting point where you wish to start recording, and start VCR to DVD d\
    uplication.
    •  The playback sound mode is followed by the setting of VCR playback sound\
     mode on page 101. Set the playback  sound mode to which you wish to record to the DVD.
    •  This unit will automatically stop the duplication if playback with no im\
    age is for more than 3 minutes during VCR  to DVD duplication.
    •  Dubbing indicator will appear on the front panel display during dubbing.\
    E9KGAUD_D-VR610KU_EN.indd   50 E9KGAUD_D-VR610KU_EN.indd   50 2007/12/18   17:10:27
    2007/12/18   17:10:27  
    						
    All Toshiba manuals Comments (0)

    Related Manuals for Toshiba Dvr610 User Manual