Toshiba Dvr610 User Manual

							Downloaded from www.Manualslib.com manuals search engine 11EN11EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
FUNCTIONAL OVERVIEW
Front Panel
19 161514
2021 171813129*10 8
124
3* 57
11
6
Rear Panel
DVDDIGITAL
AUDIO OUT AUDIO
OUT S-VIDEO
OUT IN
COAXIAL L
R L
Y
P
B/CBPR/CR
R L
R
S-VIDEO IN 
--- AU D I O --- OU T
I N  --- V I D E O  --- OU T
COMPONENT
VIDEO OUTDVD/VCRHDMI OUT
12
37911864510
Note
•  Do not touch the inner pins of the jacks on the rear 
panel. Electrostatic discharge may cause permanent 
damage to the unit.
(* )  The unit can also be 
turned on by pressing 
these buttons or by 
inserting a cassette tape.
 1. I/y ON/STANDBY button (DVD/VCR)
   Press to turn on and off the unit.
  2. Cassette compartment (VCR)
   Insert a cassette tape here.
 3.  A OPEN/CLOSE button (DVD)*
   Press to open or close the disc tray.
  4. Disc tray (DVD)
   Place a disc when it is open.
  5. VIDEO input jack (L2) (DVD/VCR)
    Use to connect external device with an RCA video cable.
  6. AUDIO input jacks (L2) (DVD/VCR)
    Use to connect external device with an RCA audio cable.
  7. DV input jack (L3) (DVD/VCR)
    Use to connect the DV output of external device with a DV cable. 8.  I REC button (DVD)
   Press once to start a recording.
    Press repeatedly to start the one-touch timer recording.
 9.  B PLAY button (DVD)*
   Press to start or resume playback.
 10.  C STOP button (DVD)
   Press to stop playback or recording.
    Press to stop the proceeding timer recording in DVD.
 11. VCR/DVD indicator
   Lights up when the VCR/DVD output mode is selected.
 12. VCR/DVD button (DVD/VCR)
   Press to select the component you wish to operate.
 13. DUBBING button (DVD/VCR)
    Press to start VCR to DVD (DVD to VCR) duplication which  you set in the main menu.  14. TRACKING 
 /  buttons (VCR)
    Press to adjust the tracking during playback or in slow  motion of the cassette tape.
    While playback is in still mode, you can stabilize the picture.
 15. Display
   Refer to “FRONT PANEL DISPLAY GUIDE” on page 18.
 16. Infrared sensor window (DVD/VCR)
    Receive signals from your remote control so that you can  control the unit from a distance.
 17.  I REC button (VCR)
    Press once to start a recording. Press repeatedly to start the  one-touch timer recording.
 18.  B PLAY button (VCR)
   Press to start playback.
 19.  A EJECT / C STOP button (VCR)
   A EJECT button
    When the unit is in stop mode, press to remove the cassette 
tape from the cassette compartment. 
   C STOP button
   Press to stop cassette tape playback or recording.
   Press to stop the proceeding timer recording in VCR.
 20.  D FWD button (VCR)
    Press to rapidly advance the cassette tape, or view the  picture rapidly in forward during playback (forward search).
 21.  E REW button (VCR)
    Press to rewind the cassette tape, or to view the picture  rapidly in reverse during playback (rewind search).
  1. AC Power Cord (DVD/VCR)
    Connect to a standard AC outlet to supply power to this unit.
  2. HDMI OUT jack (DVD only)
   Use an HDMI cable to connect to a display with an HDMI  compatible port.
  3. AUDIO OUT jacks (DVD/VCR)
    Use to connect a TV monitor, AV receiver or other device  with an RCA audio cable.
  4. VIDEO OUT jack (DVD/VCR)
    Use to connect a TV monitor, AV receiver or other device  with an RCA video cable.
  5. VIDEO IN jack (L1) (DVD/VCR)
    Use to connect external device with an RCA video cable.
  6. AUDIO IN jacks (L1) (DVD/VCR)
    Use to connect external device with an RCA audio cable.
  7. S-VIDEO IN jack (L1) (DVD/VCR)
    Use to connect the S-video output of external device with an  S-video cable.   8. COMPONENT VIDEO OUT jacks (DVD only)
    Use to connect a TV monitor with component video inputs 
with a component video cable.
  9. S-VIDEO OUT jack (DVD only)
    Use to connect the S-video input of a TV monitor, AV receiver  or other device with an S-video cable.
 10. AUDIO OUT jacks (DVD only)
    Use to connect a TV monitor, AV receiver or other device  with an RCA audio cable.
  11. COAXIAL DIGITAL AUDIO OUT jack (DVD only)
    Use to connect an AV receiver, Dolby Digital decoder or  other device with a coaxial digital input jack with a digital 
coaxial cable.
E9KGAUD_D-VR610KU_EN.indd   11 E9KGAUD_D-VR610KU_EN.indd   11 2007/12/18   17:09:38
2007/12/18   17:09:38  
						

							Downloaded from www.Manualslib.com manuals search engine 12 EN12 EN
FUNCTIONAL OVERVIEW
Remote Control
Installing the Batteries in the Remote 
Control
Keep in mind the following when using the remote 
control:
•  Make sure that there are no obstacles between the remote control and the infrared sensor window on the unit.
•  Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the infrared 
sensor window of the unit.
•  Remote control for different devices can interfere with  each other. Avoid using remote control for other device 
located close to the unit.
•  Replace the batteries when you notice a fall off in the  operating range of the remote control.
•  The maximum operable ranges from the unit are as  follows.
 -  Line of sight: approx. 23 feet (7m)
 -  Either side of the center: 
  approx. 23 feet (7m) within 30°
Install the batteries (AAx2) matching the polarity 
indicated inside battery compartment of the remote 
control.
Caution:
Never throw batteries into a fire.
Note:
•  Be sure to use AA size batteries.
•  Dispose of batteries in a designated disposal area.
•  Batteries should always be disposed of with the  environment in mind. Always dispose of batteries in 
accordance with applicable laws and regulations.
•  If the remote control does not operate correctly, or if  the operating range becomes reduced, replace 
batteries with new ones.  
•  When necessary to replace batteries in the remote  control, always replace both batteries with new ones. 
Never mix battery types or use new and used 
batteries in combination.
•  Always remove batteries from remote control if they  are dead or if the remote control is not to be used for 
an extended period of time. This will prevent battery 
acid from leaking into the battery compartment.
Using a Remote Control
1
  Open the cover.
2
 Insert batteries.
Make sure to match + and - on the batteries to 
the marks indicated in the battery compartment.
3
  Close the cover.
SE-R0295
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN
TOP MENU
WXYZ
SAT.LINK
JKL MNO
DEFTRACKING
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAU S E REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM
SEARCH
REPEAT REC
REC MODE
DUBBING
18
2
3
20
19
21
23
25
2627
3334
32
22
30
28
29
31
3635
24
4
5
7
11
12
13
9
6
8
10
1415
116
17
23feet (7m)
30˚
30˚
23feet (7m) 23feet (7m)
E9KGAUD_D-VR610KU_EN.indd   12 E9KGAUD_D-VR610KU_EN.indd   12 2007/12/18   17:09:39
2007/12/18   17:09:39  
						

							Downloaded from www.Manualslib.com manuals search engine 13EN13EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
FUNCTIONAL OVERVIEW
 1. INPUT SELECT   button
    • Press to select the appropriate input.
 2. OPEN/CLOSE  A button
  DVD mode:
    • Press to open or close the disc tray.
  VCR mode:
    •  Press to remove the cassette tape from the cassette  compartment.
 3. Number/Character buttons
    •  Press to enter values for the settings in the main menu.
  DVD mode:
    • Press to select a title/chapter/track/file on display.
    • Press to enter title names.
  VCR mode:
    •  Press to start the index/time search.
 4. SETUP button
    • Press to display the main menu.
    •  During DVD playback, press and hold for more than  3 seconds to switch the progressive scanning mode 
to the interlace mode.
  5.  DISC MENU button (DVD)
    •  Press to display the disc menu. To change original  and playlist on the TV screen.
 6. Cursor  K / L / { / B buttons
    • Press to select items or settings.
 7. CLEAR button
  DVD mode:
    •  Press to clear the password once entered, to cancel  the programming for CD, to clear the selecting 
marker number in the display menu, etc.
  VCR mode:
    • Press to reset the tape counter.
  8.  INSTANT SKIP button (DVD)
    • During playback, press to skip 30 seconds.
 9. REV  E button
  DVD mode:
    • During playback, press to fast reverse playback.
    •  When playback is in pause, press to slow reverse playback.  VCR mode:
    •  During playback, press to view the picture rapidly in  reverse.
    •  Press to fast reverse the cassette tape in stop mode.
 10.  PLAY  B button
    • Press to start playback or resume playback.
 11.  SKIP  H button (DVD)
    •  During playback, press to return to the beginning of  the current chapter, track or file.
    •  During playback, press twice in quick succession to  skip to the previous chapter or track.
    •  When playback is in pause, press repeatedly to  reverse the playback step by step.
 12.  PAUSE  F button
    • Press to pause playback or recording.
 13.  DUBBING  button
    •  Press to start VCR to DVD (DVD to VCR) duplication  which you set in the main menu.
 14.  REPEAT  button
  DVD mode:
    • Press to select the repeat mode.
  VCR mode:
    •  Press to set or release the Auto Repeat Playback. In  the Auto Repeat Playback mode, tape is played to its 
end, the tape will rewind to the beginning and start 
playback itself.
 15.  TIMER  SET  button
    •  Press to set the unit in the timer standby mode. In  the timer standby mode, press to cancel the mode 
and to turn the unit on.
 16.  HDMI  button  (DVD)
    •  Press to set the HDMI connector’s video signal  output mode.
 17. 
I/y ON/STANDBY  button
    •  Press to turn the unit on and off.   18. TRACKING 
 /  buttons (VCR)
    •  Press to adjust the tracking during playback or in  slow motion of the cassette tape.
    •  While playback is in still mode, you can stabilize the  picture.
 19.  SAT.LINK  button
    • Press to call up the Satellite Link setting.
 20.  TIMER  PROG.  button
    • Press to display the timer programming list.
 21.  AUDIO 
 button
  DVD mode:
    •  During playback, press to display the audio menu.
  VCR mode:
    •  During the playing of a HiFi video tape, press to  change the audio out setting to HiFi or mono.
 22.  DISPLAY  button
    • Press to display the display menu on or off.
 23. TOP MENU button (DVD)
    • Press to display the title list. 
 24.  ENTER  button
    • Press to confirm or select menu items.
 25.  RETURN  button
    •  Press to return to the previous displayed menu screen.
 26. TIME SLIP button (DVD)
     •  Press once to start recording the TV program you  are watching. Press again to watch the content 
being recorded from the beginning while recording 
continues. (VR mode DVD-RW with the recording 
mode of LP, EP or SLP only)
 27. 1.3x/0.8x PLAY button (DVD)
    •  During playback, press to play back in a slightly  faster/slower speed while keeping the sound output.
 28.  FWD  D button
  DVD mode:
    • During playback, press to fast forward playback.
    •  When playback is in pause, press to slow forward playback.  VCR mode:
    •  During playback, press to view the picture rapidly in  forward.
    • Press to fast forward the cassette tape in stop mode.
    •  When playback is paused, press to view the cassette  tape in slow motion. 
 29.  SKIP  G button (DVD)
    •  During playback, press to skip to the next chapter,  track or file.
    •  When playback is in pause, press repeatedly to  forward the playback step by step.
 30.  STOP  C button
    • Press to stop playback or recording.
  DVD mode:
    • Press to exit from the title list.
 31.  DVD  button
    •  Press to select the DVD output mode.
 32.  VCR  button
    •  Press to select the VCR output mode.
 33.  REC  I button
    •  Press once to start a recording.
    •  Press repeatedly to start the one-touch timer recording.
 34. REC MODE button
    • Press to switch the recording mode.
 35.  ZOOM  button  (DVD)
    •  During playback, press to enlarge the picture on the  TV screen.
 36. SEARCH button (VCR)
  •   Press to call up the index or time search menu.
Note
•  If you turn off this unit, [OPEN/CLOSE  A] on the remote 
control is not available.
Be sure to use [OPEN/CLOSE  A] or [STOP  C / EJECT A ] 
on the unit.
E9KGAUD_D-VR610KU_EN.indd   13 E9KGAUD_D-VR610KU_EN.indd   13 2007/12/19   13:45:28
2007/12/19   13:45:28  
						

							Downloaded from www.Manualslib.com manuals search engine 14 EN14 EN
Because this product is a combination of a VCR and a DVD recorder, you m\
ust select first which component you wish 
to operate with [VCR/DVD].
DVD mode
Press [DVD] on the remote control.
(Verify that the DVD indicator is lit.)
VCR mode
Press  [VCR] on the remote control.
(Verify that the VCR indicator is lit.)
Note
•  You cannot switch to another mode (DVD or VCR) in the timer-standby mo\
de.
THE VCR / DVD RECORDER SWITCHING
VCR button DVD button
DVD indicator 
VCR indicator
SE-R0295
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN
TOP MENU
WXYZ
SAT.LINK
JKL MNO
DEFTRACKING
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAU S E REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM SEARCH
REPEAT REC
REC MODE
DUBBING
E9KGAUD_D-VR610KU_EN.indd   14 E9KGAUD_D-VR610KU_EN.indd   14 2007/12/18   17:09:41
2007/12/18   17:09:41  
						

							Downloaded from www.Manualslib.com manuals search engine 15EN15EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
This unit uses the following on-screen displays and menus to guide you t\
o the easy operations.
The on-screen displays give you the information on the loaded disc, the \
disc/file in playback, or the HDMI status, etc.
The menus allow you to change the various kinds of settings for playing \
back, recording, or editing to suit your preference.
On-Screen Display / Menu
GUIDE TO ON-SCREEN DISPLAYS AND MENUS
Disc Information / MenuThe on-screen display changes in the following order 
as you press [DISPLAY].
OFF
Disc Information/Menu
Title Name Information
(only when DVD+RW/+R, VR mode DVD-RW/-R, or
unfinalized Video mode DVD-RW/-R is in playback) or
File Name Information
(only when a CD with MP3/WMA/ JPEG/DivX® files is in playback)
MP3/WMA Tag Information
(only when a MP3 or WMA file is in playback)
HDMI Information
(only for the images output through the HDMI output)
L1
1/   5 1/   5-RWVRORG0:01:00 / 1:23:45
SP 1:53
25
613
74 4
*  This is an example screen only for explanation.
1. Indicates a disc type and format mode.
2. Indicates a type of titles for VR mode DVD-RW .
3. Indicates a selected external input mode.
4. Indicates a recording mode and possible recording  time left.
5. Indicates a title number, chapter number, elapsed time  and total time of disc playback.
6.  Each icon means:
: Search
: Audio
: Subtitle
: Angle
: Repeat : Marker
: Noise Reduction / Black Level
: Zoom
: Surround
7. Indicates an operation status.
0:00:00 HIFI
SP 12:00AM
453
2
1
* This is an example screen only for explanation.
1.  Indicates current video status.
2.  Indicates the current time.
3.  Indicates a recording or playing back mode.
4.  Indicates a tape counter.
5.  Audio status of the current cassette tape.
VCR mode
DVD mode
Note
•  In some descriptions on this manual, only one disc  type is indicated as an example.
E9KGAUD_D-VR610KU_EN.indd   15 E9KGAUD_D-VR610KU_EN.indd   15 2007/12/18   17:09:41
2007/12/18   17:09:41  
						

							Downloaded from www.Manualslib.com manuals search engine 16 EN16 EN
Video Info.   :          480p  /  YCbCr
Audio Info.   :          Bitstream
21
3
4
3
*1.  Indicates the resolution of the HDMI output image.
*2. Indicates the HDMI video format.
*3. Indicates the HDMI audio format.
  4. Indicates current disc status.
*  “- - -” will be displayed, when it does not have any  information.
HDMI Information
GUIDE TO ON-SCREEN DISPLAYS AND MENUS
Title name information
Title NameMy Title
File name information
File NameMy File
Title/File Name Information
•  First, track name will be displayed.
Track Name
•  If you press [DISPLAY] one more time, artist name will be displayed.
Artist Name
•  If you press [DISPLAY] one more time, album name will be displayed.
Album Name
•  If there is no artist, track or album name, “Not Available” will be displayed.
MP3/WMA Tag Information
E9KGAUD_D-VR610KU_EN.indd   16 E9KGAUD_D-VR610KU_EN.indd   16 2007/12/18   17:09:42
2007/12/18   17:09:42  
						

							Downloaded from www.Manualslib.com manuals search engine 17EN17EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
1. Format  (DVD-RW, DVD+RW only):
  Allows you to format the disc.
2. Finalize:
  Allows you to finalize a disc containing recorded titles.
3. Disc  Protect  (VR mode DVD-RW, DVD+RW/+R only): 
  Allows you to protect a disc from accidental editing or  recording.
4. Delete All Playlists (VR mode DVD-RW only):
  Allows you to delete playlist.
5. Random  Play:
  Allows you to activate the random playback feature.
6. Program  Play:  (Audio CD only)
  Allows you to activate the program playback feature.
7. Slide  Show:  (JPEG files only)
  Allows you to select the display time of the slide show  mode.
DVD Menu
Format
Finalize
Disc Protect OFF      ONDelete All Playlists
1234
1
2
3
4

CD Playback Mode
Random Play
Program Play
Slide Show123
5
6
7

GUIDE TO ON-SCREEN DISPLAYS AND MENUS
Main Menu
Press  [SETUP]  to display the main menu. Then use 
[ K  / L ] to select a menu and  press [ENTER] to display the 
menu. T hese menus provide entries to all main functions 
of the unit. 1. General  Setting:
  To go to general setting menu.
2. Timer  Programming:
  To program a timer recording.
3. Title  List:
  To call up the title list.
4. DVD  Menu: 
  To set up the DVD setting.
5. CD Playback Mode: 
  To set up the CD playback setting.
  •  “CD Playback Mode” is available only when an audio 
CD, a CD-RW/-R with MP3 / WMA / JPEG / DivX® files is 
inserted into the unit.
Setup
Timer Programming
Title List
DVD Menu
CD Playback Mode General Setting
12345
12345
DVD Menu / CD Playback Mode
General Setting Menu
General Setting
Playback
Display
Video
Recording
Clock
DivX
HDMI
Reset All12345234
1
2
3
4
5
6
7
81. Playback:
  To set up the unit to play back discs as you prefer.
2. Display:
  To set up the OSD screen as you prefer.
3. Video:
  To set up the video setting.
4. Recording:
  To set up the unit to record to discs as you prefer.
5. Clock:
  To set up the clock of the unit as you need.
6. DivX:
  To set up the setting for the DivX® playback.
7. HDMI:
  To set up the HDMI connection setting.
8. Reset  All:
  To reset the setting to the factory default.
E9KGAUD_D-VR610KU_EN.indd   17 E9KGAUD_D-VR610KU_EN.indd   17 2007/12/18   17:09:43
2007/12/18   17:09:43  
						

							Downloaded from www.Manualslib.com manuals search engine 18 EN18 EN
FRONT PANEL DISPLAY GUIDE
Appears when data is being 
recorded on a disc.
Appears when a disc is loaded 
on the disc tray.
Appears when the disc tray is 
closing.
Appears when the disc tray is 
opening.
Display Message
Appears when HDMI output 
mode (720p) is selected.
Appears when HDMI output 
mode (1080p) is selected.
Appears when HDMI output 
mode (480p) is selected.
Appears when HDMI output 
mode (1080i) is selected.
PMBS CS DRCD
VCR
HDD
DB
DVD1
4
2
3
1. 
:  Appears in the afternoon with the clock display.
2. Title / track and chapter mark
:  Appears when indicating a title / track number.
:  Appears when indicating a chapter number.
3. Current status of the unit
:  Appears when playback is  paused.
:  Appears when playing back a disc.
:  Appears when the timer programming or OTR has 
been set and is proceeding.
:  Flashes when all timer  recordings have been 
finished.
:  Appears during recording process.
:  Flashes when a recording  pauses.
:  Appears when this unit is in DVD output mode and a disc 
is in the unit.
:  Appears during duplication  process.
:  Appears when this unit is in VCR output mode and a 
cassette tape is in the unit.
:  Appears during duplication  process.
:  Appears when this unit is in VCR output mode.
:  Appears when the timer recording is proceeding in VCR.
:  Appears when VCR is in the timer recording standby mode.
:  Flashes when a program  cannot be performed for 
some reasons.
:  Appears when this unit is in DVD output mode.
:  Appears when the timer  recording is proceeding in 
DVD.
:  Appears when DVD is in the  timer recording standby 
mode.
:  Flashes when a program  cannot be performed for 
some reasons.
:  Appears during VCR to DVD duplication process.
:  Appears during DVD to VCR  duplication process.
4. Displays the following • Elapsed playback time
•  Current title / chapter / track /file number
• Recording time / remaining time
• Clock
• Selected external input position
•  Remaining time for one-touch  timer recording 
•  Selected HDMI output mode
E9KGAUD_D-VR610KU_EN.indd   18 E9KGAUD_D-VR610KU_EN.indd   18 2007/12/18   17:09:44
2007/12/18   17:09:44  
						

							Downloaded from www.Manualslib.com manuals search engine 19EN19EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
OUT IN
DVDDIGITAL
AUDIO OUT AUDIO
OUT S-VIDEO
INL
Y
PB/CBPR/CRR L
R
S-VIDEO I N  --- AU D I O --- OU T
I N  --- V I D E O --- OU T
COMPONENTVIDEO OUTDVD/VCRHDMI OUT
ANT. IN
AUDIO INLRVIDEO IN
AUDIO OUT
LRVIDEO OUT
S-VIDEO
OUT
IN L
R L
R
S-VIDEO IN --- AUDIO --- OUT
IN --- VIDEO --- OUT
DVD/VCR
rear of your TV
external tuner
rear of this unit  RF coaxial cablee.g.)
TV signal
RCA audio
cable
RCA audio cable
RCA video cable
RCA video cable
S-video cable  RF coaxial cable
or
rear of your TV
disconnect
HDMI OUT
rear of your TV
rear of this unit
connect
CONNECTION TO AN EXTERNAL TUNER
Note
•  Required cables and connecting methods differ depending on the external \
tuner.
For more information, please contact your external tuner provider.
•  Instead of using VIDEO OUT jack of this unit, you can also use S-VIDEO O\
UT jack, COMPONENT VIDEO OUTPUT  jack, or HDMI OUT jack (no AUDIO OUT jack connection required) for con\
necting to your TV.
With this setup:
•  You can record any unscrambled channel by selecting the channel on the e\
xternal tuner. Be sure that the external  tuner is turned on.
•  Signal from the external tuner can be output only on CVBS output even wh\
en the power of the unit is off.
•  You cannot record one channel while watching another channel.
2
  Make the connection as illustrated below.
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
Note to CATV system installer
•  This reminder is provided to call the cable TV system installer’s att\
ention to Article 820-40 of the National Electrical  Code, which provides guidelines for proper grounding - in particular, sp\
ecifying that the cable ground shall be 
connected to the grounding system of the building, as close to the point\
 of cable entry as possible.
1
  Disconnect the power cords of the devices from the AC outlet.
This section describes how to connect this unit to an external tuner suc\
h as cable/satellite box.
• When you change the connections, all devices should be turned off.
• Refer to the operation manual accompanying external devices for mor\
e information.
4
  After making the connection as described above, make 
sure to select the appropriate video input type by 
following the steps in “SETTINGS FOR THE VIDEO INPUT” 
on page 20.
3
  Plug in the power cords of the devices to the AC outlet.
E9KGAUD_D-VR610KU_EN.indd   19 E9KGAUD_D-VR610KU_EN.indd   19 2007/12/18   17:09:46
2007/12/18   17:09:46  
						

							Downloaded from www.Manualslib.com manuals search engine 20 EN20 EN
SETTINGS FOR THE VIDEO INPUT
You must let the unit know which video input jack you are using before m\
aking a recording.
1
 Press [SETUP]. 
2
 Use [K / L] to select “General Setting”, then press [ENTER].
3
 Use [K / L] to select “Video”, then press [ENTER].
4
 Use [K / L] to select “Select Video”, then press [ENTER].
5
 Use [K / L] to select the input jack type to connect, then press [ENTER].
If you want to use VIDEO IN jack, select “Video 
In”.
 If you want to use S-VIDEO IN jack, select 
“S-Video In”.
General Setting
Playback
Display
Video
Recording
Clock
DivX
HDMI
Reset All Progressive
TV Aspect
Select Video
Select Video - L1 (Rear)Video In
S-Video In
6
  Press [SETUP] to exit.SE-R0295
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN
TOP MENU
WXYZ
SAT.LINK
JKL MNO
DEFTRACKING
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAU S E REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM
SEARCH
REPEAT REC
REC MODE
DUBBING
ENTER
SETUP
E9KGAUD_D-VR610KU_EN.indd   20 E9KGAUD_D-VR610KU_EN.indd   20 2007/12/18   17:09:47
2007/12/18   17:09:47