Toshiba Dvr610 User Manual

							Downloaded from www.Manualslib.com manuals search engine 111EN111EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
LIMITED WARRANTY
,)7+($93528&7)$,/672:25.$6:$55$17($%29(

						

							Downloaded from www.Manualslib.com manuals search engine 97EN97EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
2HDMI Audio (Default : ON)
If you do not want to output the audio through HDMI 
(when you digitally output the audio through the 
COAXIAL DIGITAL AUDIO OUT jack to your audio system, 
etc.), you can set the HDMI audio output off.
Use [K / L] to select a setting, then press [ENTER].
•  Set to “OFF” when the HDMI sound is not output.
General Setting
Playback
Display
Video
Recording
Clock
DivX
HDMI
Reset All Format
HDMI Audio
RGB Range
HDMI CEC
HDMI AudioON
OFF
Your setting will be activated.
3RGB Range (Default : Normal)
You can adjust the RGB range to make the dark areas of 
the HDMI images brighter.
Use [K / L] to select a setting, then press [ENTER].
•  Select “Enhanced“ if the black-white contrast is not clear.
•  This setting is effective only for HDMI RGB output.
General Setting
Playback
Display
Video
Recording
Clock
DivX
HDMI
Reset All Format
HDMI Audio
RGB Range
HDMI CEC
RGB RangeNormal
Enhanced
Your setting will be activated.
GENERAL SETTING
HDMI (cont’d)
E9KGAUD_D-VR610KU_EN.indd   97 E9KGAUD_D-VR610KU_EN.indd   97
2007/12/18   17:11:32
2007/12/18   17:11:32  
						

							Downloaded from www.Manualslib.com manuals search engine 98 EN98 EN
Reset the setting to default.
1
  Press [SETUP] in stop mode and use [K / L] to select “General Setting”, 
then press [ENTER].
2
 Use [K / L] to select “Reset All”, then press [ENTER].
General Setting
Playback
Display
Video
Recording
Clock
DivX
HDMI
Reset All
3
  Select “Yes” using [K / L] , then press  [ENTER].
General Setting
Playback
Display
Video
Recording
Clock
DivX
HDMI
Reset All
Reset to factory default? Ye sNo
“Are you sure?” will appear.  Select “Yes” using 
[K / L] and then press [ENTER].
Your setting will be initialized.
Reset All
Note
•  The settings listed below will remain unchanged  even after resetting to the factory default.
  - Clock setting
  - OSD language setting
  - Parental lock setting
  - DivX® VOD code
  - V-Chip setting
  - Timer programs
GENERAL SETTING
SE-R0295
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN
TOP MENU
WXYZ
SAT.LINK
JKL MNO
DEFTRACKING
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAU S E REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM
SEARCH
REPEAT REC
REC MODE
DUBBING
ENTER
SETUP
E9KGAUD_D-VR610KU_EN.indd   98 E9KGAUD_D-VR610KU_EN.indd   98 2007/12/18   17:11:32
2007/12/18   17:11:32  
						

							Downloaded from www.Manualslib.com manuals search engine 99EN99EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
VCR FUNCTIONS
PlaybackRecording
1) Press  [I/y ON/STANDBY] on the remote control or 
the front panel of the unit.
When you are playing back a cassette tape, turn on the 
TV and be sure to select the input to which the unit is 
connected.
Press [VCR].
2) Insert a prerecorded cassette tape. Press [PLAY B]  to begin playback.
3) During playback, press [PAUSE F]. Playback will pause and sound will be muted.
4) Press  [PLAY  B] to resume playback.
5) Press  [STOP  C] to stop playback.
6) Press  [OPEN/CLOSE  A] to eject the cassette tape.
Note
•  When a cassette tape ends during playback, fast-
forward or normal recording, the unit will 
automatically rewind to the beginning of the 
cassette tape. After rewinding finishes, the unit will 
eject the cassette tape.
•  When a cassette tape without erase-protection tab is  inserted, the unit will start playback automatically.
•  Tracking will be automatically adjusted upon  playback. To adjust the tracking manually, press 
[TRACKING 
 / ].
Press [VCR] first.
Before recording, make sure:
•  The appropriate external input position (L1/L2) to which your external tuner is connected is selected by pressing 
[INPUT SELECT 
].
•  There is a cassette tape with an erase-protection tab in  the unit.
•  The desired recording speed is selected in SP (standard  playback) or SLP (super long playback) mode by 
pressing  [REC MODE].
Recording speed:
Tape speed Recording / playback time
Type of tape T60 T120 T160
SP 1hour 2hours 2-2/3hours
SLP 3hours 6hours 8hours
•  Refer to pages 38-41 for instructions on timer recording.
1) Press  [REC  I] to begin the recording.
To temporarily stop recording or to resume it, press 
[PAUSE  F]. After the unit has been in pause mode for 
5 minutes, it will stop automatically to protect the 
cassette tape and the video head from damage.
2) Press  [STOP  C] when the recording is completed.
Accidental erasure prevention
To prevent accidental recording on a 
recorded cassette tape, remove its erase-
protection tab. To record on it later, cover 
the hole with cellophane tape.
erase-protection tab
E9KGAUD_D-VR610KU_EN.indd   99 E9KGAUD_D-VR610KU_EN.indd   99 2007/12/18   17:11:33
2007/12/18   17:11:33  
						

							Downloaded from www.Manualslib.com manuals search engine 100 EN100 EN
VCR FUNCTIONS
One-touch Timer Recording (OTR)Index Search
This feature allows you to set the recording length simply 
by pressing [REC I] on the remote control.
Press [VCR] first.
1) During normal recording, press [REC I] to begin  the one-touch timer recording.
You can select a fixed recording time by pressing 
[REC  I] repeatedly.
(0:30) (1:00)(Normal recording)
(7:30)
(8:00)
When the one-touch timer recording is finished, the 
unit will turn off automatically.
To change the recording length during the one-touch 
timer recording, press [REC  I] repeatedly until the 
desired length appear.
To cancel the one-touch timer recording within the 
specified time, press [STOP  C].
Note
•  The remaining recording time will be displayed on 
the front panel display during one-touch timer 
recording. Press [DISPLAY] to see it on the TV screen.
•  You cannot pause the one-touch timer recording.
•  If VCR the one-touch timer recording is completed  during DVD playback or recording, the VCR will be in 
stop mode and the DVD keeps the current mode.
•  Unlike a timer recording, you can perform the  following operations during the one-touch timer 
recording.
  -  Turning off the power (One-touch timer recording  will be canceled.).
 - Using  [REC I] or [STOP  C].
•  When the one-touch timer recording is finished and  the power is turned off, the unit will switch to the 
standby mode automatically if a timer recording has 
been programmed. Press [TIMER SET] to cancel the 
standby mode for using the unit continuously.
An index mark will be assigned at the beginning of each 
recording you make. You may skip to a specific marked 
point by following the steps below.
Press [VCR] first.
1) Press [SEARCH] so that “INDEX SEARCH” menu  appears.
2) Using [the Number buttons], enter the number of  recordings you wish to skip within 30 seconds.
 
 INDEX SEARCH
         03
3) Press  [REV  E], [FWD D] to start index search.
If you want to go in the forward direction, press 
[FWD  D].
If you want to go in the reverse direction, press 
[REV  E].
After index search, the VCR will play back the cassette 
tape automatically.
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5
02 01 01 02 03
Beginning 
of tape End 
of tape
CURRENT PROGRAM
INDEX MARK
Note
•  You can make the index mark up to 20.
E9KGAUD_D-VR610KU_EN.indd   100 E9KGAUD_D-VR610KU_EN.indd   100
2007/12/18   17:11:34
2007/12/18   17:11:34  
						

							Downloaded from www.Manualslib.com manuals search engine 101EN101EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
VCR FUNCTIONS
Time SearchOther Operations
This feature allows you to go to a specific point on a 
cassette tape by entering the exact amount of time you 
wish to skip in order to reach the point.
Press [VCR] first.
1) Press [SEARCH] repeatedly so that “TIME SEARCH” 
menu appears.
2) Using [the Number buttons], enter your desired  time to skip within 30 seconds.
You can set the time up to 9:59.
 TIME SEARCH
       2:50
3) Press  [REV  E], [FWD D] to start time search.
If you want to go in the forward direction, press 
[FWD  D].
If you want to go in the reverse direction, press 
[REV  E].
After time search, the unit will play back the cassette 
tape automatically.
Note
•  Index search and time search are not available  during recording.
• Press  [STOP C] to stop the search.
•  If the end of the cassette tape is reached during  search, this unit will cancel the search and rewind the 
cassette tape.
Press [VCR] first.
Fast forward:
When the unit is in stop mode, press [FWD  D] to fast 
forward the cassette tape.
Rewind:
When the unit is in stop mode, press [REV  E] to rewind 
the cassette tape.
To cue or review picture during playback (picture search):
Press  [REV E], [FWD  D] during playback.
Press it again and the unit will search in super high 
speed. (in the SLP mode only)
To freeze the picture on TV screen during playback 
(still mode):
Press  [PAUSE  F]. Each time you press the button, the 
picture will be forwarded by one frame.
If the picture begins to vibrate vertically during the still 
mode, stabilize the picture by pressing [TRACKING  / ] 
on remote control.
If the picture is distorted or rolling vertically, adjust the 
vertical hold control on your TV, if equipped.
Counter reset:
Press  [CLEAR] to reset the counter to “0:00:00”.
To playback in slow motion:
Press  [PAUSE  F] during playback, then press [FWD  D].
Press  [FWD  D] or [REV  E] repeatedly to select the 
desired speed.
Automatic rewind:
When a cassette tape is played back or fast forwarded to 
its end, the cassette tape will rewind to the beginning, 
stop and eject itself.
To repeat a playback indefinitely without touching 
[PLAY  B] (Auto Repeat Playback):
During normal playback, press [REPEAT]. When a tape is 
played to its end, the tape will rewind to the beginning and 
start playback itself. To cancel the Auto Repeat Playback, 
press  [REPEAT] again.
When you playback a cassette tape recorded in Hi-Fi 
stereo:
Press  [AUDIO ] on the remote control to select Hi-Fi or 
MONO for playback sound mode.
•  If you have connected a stereo TV to this unit, select “HIFI”.
•  If you have connected a monaural TV to this unit, select  “MONO”.
HIFIYour Selection
Type of recorded tapenon Hi-Fi tapes
Hi-Fi tapes 
recorded in  Hi-Fi stereo
Hi-Fi tapes 
recorded second  audio program Hi-Fi tapes 
recorded main  audio program MONO
Monaural
L+R
Main audio  program
Second audio  program
Monaural
R-channel
L-channel
R
Main audio  program
Second audio  program
Monaural
L
Main audio  program
Second audio  program
Note
•  Still/slow mode will stop after 5 minutes to prevent 
damage to the cassette tape and the video head.
•  To return to playback from the picture search/still/ slow mode, press [PLAY  B].
E9KGAUD_D-VR610KU_EN.indd   101 E9KGAUD_D-VR610KU_EN.indd   101 2007/12/18   17:11:35
2007/12/18   17:11:35  
						

							Downloaded from www.Manualslib.com manuals search engine 102 EN102 EN
TROUBLESHOOTING
Before requesting service for this unit, check the table below for a pos\
sible cause of the problem you are experiencing. 
Some simple checks or a minor adjustment on your part may eliminate the \
problem and restore proper operation.
SymptomRemedy
D V
D •
V CR The power does not turn on. • Check that the AC power cord is connected securely.
• Check the breaker (in case of power failure).
• Press [TIMER SET] to cancel the timer standby mode.
There is no picture. • Re-connect the connecting cords securely.
• Check if the connecting cords are damaged.
• Check the connection to your TV (page 21).
• Check if the progressive scan mode is set correctly according to yo\
ur TV 
(page 94).
• Switch the input selector on your TV (such as to “L1”) so that t\
he signal  from the unit appears on the TV screen.
Cannot record a TV program. • This unit does not have a tuner to receive TV broadcasting. • You must connect this unit to an external tuner to record TV programs (page 19).
TV program pictures are distorted. • Check if all the connections are made correctly (page 21).
Playback picture is distorted. • Keep the device which may cause electrical disturbances, such as a  cellular phone, away.
Playback picture or TV program from 
the device connected through the unit 
is distorted. • If the playback picture output from a DVD player, VCR or tuner goes 
through the unit before reaching your TV, the copy-protection signal 
applied to some programs could affect picture quality. Disconnect the 
playback device in question and connect it directly to your TV.
There is no sound. • Re-connect all connections securely.
• Check if the connecting cord is damaged.
• Check the connections to the amplifier input.
• Check if the input device setting on the amplifier is correct.
• When the unit is in pause mode or in slow-motion playback mode, 
sound is not output. This is not a malfunction.
• When the unit is in fast forward or fast reverse mode, sound is not  output. This is not a malfunction.
• If the audio signal does not come through the DIGITAL AUDIO OUT  (COAXIAL) jack, check the setting in “Audio Out” (page 89).
No DTS sound on digital output. • Change the setting menu for “DTS” to “ON”.
No DTS sound from analog output • This unit has no analog sound output when playing back the selected  DTS sound mode.
Nothing was recorded even though 
you set the timer setting correctly. • There was a power failure during recording.
• The unit’s internal clock stopped due to a power failure that lasted \
for 
more than 30 seconds.  Reset the clock (page 26).
• The program contains copy protection signals that restricts copying.
• The timer setting overlapped with another setting that has priority.
Timer recording does not start. • No disc is inserted. •  A disc is not recordable (finalized DVD-RW/-R, finalized DVD+R, a fully\
 recorded disc, etc.). 
Timer recording is not complete or did 
not start from the beginning. • The timer setting overlapped with another setting that has priority 
(page 41).
•  Disc space was not enough.
•  “Make Recording Compatible“ is not set to “ON”, when recordi\
ng onto  DVD+RW/+R that was recorded on other unit.
Timer recording is impossible. • Make sure 
 appears on the front panel display of this unit. If not, press 
[TIMER SET].
The remote control does not function. • Batteries are weak.
• There are obstacles between the remote control and the unit.
• The remote control is far from the unit.
• There are no batteries in the remote control.
• Check if the unit is turned on.
• The remote control is not pointed at the infrared sensor window on the u\
nit.
• Press [DVD] or [VCR], whichever you need. Then, try again.
• Press [TIMER SET] to cancel the timer standby mode.
The unit does not operate properly. • When static electricity, etc., causes the unit to operate abnormally,  unplug the unit and then plug it in again.
E9KGAUD_D-VR610KU_EN.indd   102 E9KGAUD_D-VR610KU_EN.indd   102 2007/12/18   17:11:36
2007/12/18   17:11:36  
						

							Downloaded from www.Manualslib.com manuals search engine 103EN103EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
TROUBLESHOOTING
Symptom Remedy
D V
D •
V CR DV signal cannot be input.
• Before connection, turn on the power supplies for both this unit and the\
 
DVC, and make sure that these units are in stop mode.
• Only a “DVC-SD” signal can be input from the DVC to this unit. Oth\
er  types of signals are not supported.
• Do not connect any device other than the DVC. Even if a recorder or PC  with another DV terminal is connected, the DV function will not operate.\
• If the DVC is not recognized after connection, turn off the power supply\
  for the unit and re-connect the DVC.
The DVC cannot be operated with this 
unit. • Signal input or DVC operation from this unit may be disabled 
depending on the type of DVC.
• If a DVC signal cannot be input, use an external input (L1/L2) for ana\
log  connection via audio/video cables.
• DVC control may be disabled depending on the type of DVC, even in a  mode other than camera mode. In this case, switch to DVD control and 
execute the normal recording procedure while operating the DVC.
Certain functions of the unit cannot 
operate. • Some functions may not operate depending on the type of DVC. For 
example, if the DVC does not support slow playback mode, the slow 
playback function is disabled.
• With L3 (DV), the disc display menu does not appear unless disc  playback is executed.
DV audio signal cannot be switched. • For recording with the DVC, the recording audio signal can be set to 12 \
 bits or 16 bits. However, when 16-bit recording mode is selected, audio \
signal cannot be switched. To record an audio signal, set it to 12 bits.\
D V
D There is no picture.
• If the setup menu appears on the TV screen, press [RETURN] to exit.
• Check if the progressive scan mode is set correctly according to your TV\
 
(page 94).
Picture noise appears. • Clean the disc with a cleaning cloth.
Playback picture from the external 
devices connected to this unit is 
distorted. • If the picture output signal from the external devices passes through th\
is 
unit to get to your TV, the copy protection signal applied to some DVD c\
ould 
affect the picture quality. Disconnect the playback device in question a\
nd 
connect it directly to your TV.
There is no sound. • If you are using  DIGITAL AUDIO OUTPUT (COAXIAL) jack, check the setting 
in “Audio Out” (page 24).
• Clean the disc with a cleaning cloth.
Sound is noisy. • Clean the disc with a cleaning cloth.
The disc does not play back. • No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labeled side facing up\
.
• The disc is not correctly inserted.
• The unit cannot play back certain discs (such as a CD-ROM) (page 10)\
.
• The region code on the DVD-video does not match the unit (page 10).
• Moisture has condensed inside the unit. Remove the disc and leave the 
unit turned on for about 2 hours until the moisture evaporates (page 4)\
.
• If the disc was recorded on another recorder, the unit cannot play back \
 the disc if it was not finalized.
Playback image freezes for a second. • During the playback of 2 layered disc, picture may freeze for a moment  when the 1st layer switches to the 2nd layer. This is not a malfunction.\
Discs recorded on this unit cannot be 
played back on other DVD players. • If you are using DVD-RW/-R or DVD+R, please ensure you finalized the 
disc after recording (pages 30-32).
The disc does not start playback from 
the beginning. • Resume playback was activated (page 58). Press [STOP 
C] twice.
• You have inserted a disc whose title menu or DVD menu automatically  appears on the TV screen when it is first inserted.
The unit starts playing back the disc 
automatically. • The DVD-video features an auto playback function.
Some functions such as stop, search, 
or slow-motion playback cannot be 
performed. • Depending on the disc, you may not be able to do some of the 
operations. Refer to the instruction manual supplied with the disc.
The language for the sound track 
cannot be changed. • The title does not have the multilingual audio tracks.
• The DVD-video prohibits the changing of the language for the sound 
track.
E9KGAUD_D-VR610KU_EN.indd   103 E9KGAUD_D-VR610KU_EN.indd   103 2007/12/18   17:11:36
2007/12/18   17:11:36  
						

							Downloaded from www.Manualslib.com manuals search engine 104 EN104 EN
TROUBLESHOOTING
SymptomRemedy
D V
D The subtitle language cannot be 
changed or turned off.
• Multilingual subtitle are not recorded on the DVD-video.
The angles cannot be changed. • Multi-angles are not recorded on the DVD-video being played back. • The angle-change operation is whenever possible as long as the disc contains a multi-angle portion. Actual change will be performed when 
the portion has come up.
• The DVD-video prohibits changing angles.
• Try changing the angle using the DVD-video’s menu.
Recording does not stop immediately 
after you press [STOP  C]. • It may take a few seconds for the unit to input disc data before 
recording stops.
The disc tray does not open when you 
press  [OPEN/CLOSE  A]. • It may take a few seconds for the disc tray to open after you have 
recorded or edited a disc. This is because the unit is adding disc data \
to 
the disc.
“Repairing” appears on the TV screen.
Repairing 88%
• If there is a power failure or unplugging during recording, finalizing, \
formatting or editing (even after “Repairing” disappears), a rep\
airing 
process will begin automatically just after turning the unit on again.
  It may take several minutes up to about several hours.
In a case you intend to cancel the 
repairing process.
Repairing 88%
Do you want to cancel a repairing
process ? When selecting “Yes”, the disc may not be usable.
Ye sNo
• If you intend to cancel the repairing process, press [A  OPEN/CLOSE] 
on the front panel, then select “Yes” and press [ENTER]. After that, press 
[OPEN/CLOSE  A] to take out the disc. The disc canceled during the 
repairing process MAY NOT work. 
No image from HDMI connection. • Check the HDMI connection. (Check the status of the HDMI related  indications.)
• Check whether the connected monitor device or other device supports  HDCP. (This unit will not output a video signal unless the other device\
 
supports HDCP.)
• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches  the supported input format of other connected device.
• If the unit is connected to the unauthorized display device with an  HDMI cable, the audio/video signal may not be output when playing 
back a commercial DVD-video.
There is no sound or the sound is 
distorted. • The HDMI sound is not output when “HDMI Audio” is set to “OFF”\
.
• Check the RCA audio cable connection. If you are using HDMI-DVI 
conversion cable, you must connect the RCA audio cable, too.
• Check whether the output format of this unit (HDMI FORMAT) matches  the supported input format of other connected device.
V CR There is no picture.
• If you connect the cable to S-VIDEO OUT/ COMPONENT VIDEO OUT / 
HDMI OUT jack, try connecting it to AUDIO / VIDEO OUT jack instead.
Picture noise appears. • Head cleaning for VCR may be necessary. Refer to “Auto Head Cleaning”\
 
(page 5).
• Adjust tracking control for better picture by pressing [TRACKING 
 / ] 
while you are playing back a cassette tape.
The cassette tape does not play back. • No cassette tape is inserted.
The tape ejected after you press 
[REC  I]. • Make sure the cassette tape has an erase-protection tab when you 
record to a cassette tape. If needed, cover the hole with cellophane 
tape.
The remote control does not function. • Check if a cassette tape is in this unit.
The motor rotates even when 
playback / recording is stopped. • The motor may rotate for the duration of approximately 5 minutes for 
efficient operation. This is not a malfunction.
E9KGAUD_D-VR610KU_EN.indd   104 E9KGAUD_D-VR610KU_EN.indd   104 2007/12/18   17:11:36
2007/12/18   17:11:36  
						

							Downloaded from www.Manualslib.com manuals search engine 105EN105EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
TROUBLESHOOTING
Error message CauseSolution
Disc Error
— Please eject the disc. —
Playback feature may not be available on this disc.
• Unplayable disc is inserted in the unit.
• The disc is upside down. • Insert the standardized disc which have 
the marks on pages 9-10.
• 
Insert the disc with the labeled side facing up.
Region Error
— Please eject the disc. —
Playback is not authorized in your region. • Playback is not authorized in the region 
of the DVD-video which you inserted in 
the unit. • Insert the DVD-video with region codes 
1 or ALL.
Parental Lock On
The current selected parental level 
prohibits playback. • The current selected parental level 
prohibits playback. • Check “Parental Lock” setting in 
“Playback” menu (page 88).
Recording Error
This program is not allowed to be recorded.• You are trying to record the copy  prohibited program. • You cannot record copy prohibited 
programs.
Recording Error
This program is not recordable in Video 
mode. • You are trying to record the copy-once 
program onto the DVD-RW disc in 
Video mode. • Set “Format Mode” to “VR mode” 
(pages 27-28).
Recording Error
This program is not recordable in +VR mode.• You are trying to record the copy-once  program. • Insert the DVD-RW disc in VR mode 
(ver.1.1 or 1.2 compatible with CPRM).
Recording Error
Cannot record on this disc. • You are trying to record onto the disc 
which is unrecordable, or the disc status 
is unable to record.
• The disc is dirty.
• The disc is damaged. • Insert the recordable disc, and ensure 
the disc status satisfies the recording 
requirements (page 9).
• Clean the disc with a cleaning cloth.
• Replace the disc.
Recording Error
This program is not allowed to be 
recorded on this disc. • You are trying to record the copy-once 
program onto the DVD-RW disc which 
is not compatible with CPRM. • Insert the DVD-RW disc in VR mode 
(ver.1.1 or 1.2 compatible with CPRM).
Recording Error
This disc is protected and not recordable. • 
You are trying to record onto the protected 
disc which is set in “DVD Menu” menu.• Release the disc protect setting in “DVD 
Menu” menu (page 29).
Recording Error
Disc is full. 
(No area for new recording) • You are trying to record onto the disc 
which has no space for recording. • Insert the recordable disc with enough 
recording space.
Recording Error
You cannot record more than 99 titles on one disc. (The maximum is 99) • 
You are trying to record onto the DVD-
RW/-R on which the number of recording 
titles comes up to the maximum (99). • Delete unnecessary titles (page 72).
Recording Error
You cannot record more than 999 chapters on one disc. (The maximum is 999) • 
You are trying to record onto the VR mode 
DVD-RW on which the number of recording 
chapters comes up to the maximum (999).• Delete unnecessary chapter marks 
(page 77).
Recording Error
You cannot record more than 49 titles on one disc. (The maximum is 49) • 
You are trying to record onto the DVD+RW/
+R on which the number of recording titles 
comes up to the maximum (49). • Delete unnecessary titles (page 72).
Recording Error
You cannot record more than 254 chapters on one disc. (The maximum is 254) • 
You are trying to record onto the DVD+RW 
on which the number of recording 
chapters comes up to the maximum (254). • Delete unnecessary chapter marks 
(page 77).
Recording Error
You cannot record on this disc as Control 
Information is full. • 
This disc has no space to write the Control 
Information when recording or deleting contents.
When editing has been repeatedly performed, 
the control Information area may come up to be 
full even the recording area has enough space.
• Delete unnecessary titles 
(page 72).
Recording Error
You cannot record on this disc as Power 
Calibration Area is full.
• When recordings are performed 
repeatedly onto an unstable disc, this 
area may come up to be full.
• Every time you insert a disc for recording, 
the disc’s working area will be taken up. 
And if you repeat this frequently, it will 
be used up sooner and you may not be 
able to record full 49 titles.
• Insert a new disc.
Recording Error
This disc is already finalized. • You are trying to record onto the disc 
already finalized. • Undo the finalizing for this disc 
(page 32).
Recording Error
The disc has no recording compatibility. 
Set “Make Recording Compatible” to 
“ON” to convert the disc. • You are trying to record onto the 
unfinalized +VR mode discs recorded 
on other unit. • Set “Make Recording Compatible” to 
“ON” to rewrite the menu, after that you 
will record to disc (page 34).
*  If you are still having trouble with the unit after checking “TROUBLE\
SHOOTING”, write down the error code and the  error description for calling our help line to locate an Authorized Serv\
ice Center.
– Can I record to CD-RW/-R?  No, this unit records only DVD.
– Can I play back DVD-video that is bought in another country?  Possible when the region code of the disc is 1 and All.
– Can I connect the unit to my PC?  No, you cannot control the unit by PC.
– Can I program a timer recording with cable/satellite box?   
Yes, you can. Select “L1” or “L2” as your recording channel,\
 
and leave the cable/satellite box on (pages 20, 38-41).
Frequently Asked Questions
E9KGAUD_D-VR610KU_EN.indd   105 E9KGAUD_D-VR610KU_EN.indd   105 2007/12/18   17:11:37
2007/12/18   17:11:37