Toshiba Bex4t2g Manual

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-27 
2.6.7  Dump Mode Setting 
 
 
 
 
 
 
 
 In Dump Mode, the data in the receive buffer is printed.  The data 
is expressed in hexadecimal values.  This operation allows 
verification of the programming commands or the debug of the 
program.  
(1) BUFFER 
Select the receive buffer to dump.  
 
•  RS-232C  RS-232C receive buffer 
•  CENTRONICS  Centronics receive buffer 
•  LAN  Network I/F receive buffer 
•  BASIC1  BASIC Interpreter:   
 I/F → Interpreter buffer 
• BASIC2  BASIC Interpreter: 
   Interpreter buffer → I/F 
•  USB  USB receive buffer 
• RFID  RFID receive buffer 
 
 
(2) DUMP LIST 
  This parameter is to choose the output destination. 
 
•  USB MEMORY  Saves in the USB memory. → c 
• PRINT  Prints out → d 
 
c  When USB MEMORY is selected: 
  A file is automatically created in the USB memory and named in 
the following format based on the printer model and saved date. 
 /ATA0/DUMP/B-EX4T1_DUMP_1007291030.BIN 
  (e.g. B-EX4T Type1, 10:30, July 29, 2010) 
 
 
d  When PRINT is selected: 
  Choose a printing method. 
• ON DEMAND  Prints 166 lines of data (approx. 50 cm), then 
stops.  Subsequent data is printed when the 
[ENTER] key is pressed. 
• ALL  Prints all data in the receive buffer. 
 
 
USER SYSTEM MODE  
BASIC 
Z-MODE 
AUTO CALIB 
DUMP MODE 
NOTES: 
1.  If a file with the same name 
already exists in the USB 
memory, it will be 
overwritten. 
2.  Selecting “RS-232C” or 
“CENTRONICS” without 
the optional board installed 
causes a 0-KB file to be 
output.  
3.  If an error occurs while 
using the USB memory, the 
error message is displayed. 
For details, refer to Section 
2.6.12 Copying Data 
to/from USB Memory.  
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-28 
2.6.7  Dump Mode Setting 
 (Cont.) 
 
 The data in the receive buffer is printed as follows.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Receive Buffer Size 
Interface B-EX4T2-GS/TS/HS 
RS-232C  1MB (65536 lines) 
Centronics  1MB (65536 lines) 
LAN  1MB (65536 lines) 
BASIC 1  8KB (512 lines) 
BASIC 2  8KB (512 lines) 
USB  1MB (65536 lines) 
RFID  8KB (512 lines) 
 
Required Media Length 
Interface B-EX4T2-GS/TS  B-EX4T2-HS 
RS-232C  198.2 m  198.6 m 
Centronics  198.2 m  198.6 m 
LAN  198.2 m  198.6 m 
BASIC 1  2 m  2 m 
BASIC 2  2 m  2 m 
USB  198.2 m  198.6 m 
RFID 2 m - 
  *: Media length required for printing all data in the receive buffer. 
 
:
: 
: 
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
 7B 41 58 3B 2B 30 30 30 2C 2B 30 30 30 2C 2B 30  {AX;+000,+000,+0 
 30 7C 7D 7B 44 30 37 37 30 2C 31 31 30 30 2C 30  0|}{D0760,1100,0 
 37 34 30 7C 7D 7B 43 7C 7D 7B 4C 43 3B 30 30 33  740|}{C|}{LC;003 
 30 2C 30 30 32 30 2C 30 30 33 30 2C 30 36 36 30  0,0020,0030,0660 
 2C 30 2C 32 7C 7D 7B 4C 43 3B 30 30 37 30 2C 30   0,2|}{LC;0070,0 
 30 32 30 2C 30 30 37 30 2C 30 36 36 30 2C 30 2C   020,0070,0660,0, 
 39 7C 7D 7B 4C 43 3B 30 30 35 30 2C 30 30 32 30  9|}{LC;0050,0020 
: 
: 
: 
 44 45 46 47 48 49 4A 7C 7D 7B 50 43 31 30 3B 30   DEFGHIJ|}{PC10;0 
 33 35 30 2C 30 34 30 30 2C 31 2C 31 2C 4B 2C 30   350,0400,1,1,K,0 
 30 2C 42 3D 41 42 43 44 65 66 67 68 69 6A 6B 6C   0,B=ABCDefghijkl 
 
 6D 6E 6F 70 7C 7D 7B 50 56 30 32 3B 30 33 33 30  mnop|}{PV02;0330 
 2C 30 36 36 30 2C 30 32 37 30 2C 30 32 35 30 2C   0660,0270,0250, 
 41 2C 30 30 2C 42 3D 42 7C 7D 7B 50 56 30 33 3B  A,00,B=B|}{PV03; 
: 
: 
: 
 3B 30 39 30 30 2C 30 31 38 30 2C 54 2C 48 2C 30   ;0900,0180,T,H,0 
 35 2C 41 2C 30 3D 31 32 33 34 35 36 37 38 39 30  5,A,0=1234567890 
 41 42 43 44 45 7C 7D 00 00 00 00 00 00 00 00 00  ABCDE|}......... 
: 
: 
:
 
Print Conditions 
• Printing width: 3.9 inches 
(Approx. 100 mm) 
• Sensor selection: None 
• Print speed: 6”/sec. (203 dpi) 
  5”/sec. (300 dpi) 
3”/sec. (600dpi) 
• Printing mode: Depends on 
the selection in use. 
• 16 bytes/line 
• Data is printed in the order 
from the new one to the old. 
• Data specified by the receive 
buffer write pointer will be 
printed in boldface. 
NOTE: 
If an error occurs while 
printing, the printer stops 
printing and shows an error 
message. 
To clear the error, press the 
[PAUSE].  
After clearing the error the 
printer does not resume 
printing automatically.  
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-29 
2.6.8 Logging 
 
 
 
 
 
 The Log menu allows the saving of print logs to USB memory. 
 
(1) LOG 
 
•  PRINTER TO USB  Saves print logs in the USB memory. 
 
  A file is automatically created in the USB memory and named in 
the following format based on the printer model and saved date. 
 /ATA0/LOG/B-EX4T1_LOG_1007291030.TXT 
  (e.g. B-EX4T Type1, 10:30, July 29, 2010)  
 
 
 
 
USER SYSTEM MODE  
Z-MODE 
AUTO CALIB 
DUMP MODE 
LOG 
NOTES: 
1.  If a file with the same 
name already exists in the 
USB memory, it will be 
overwritten. 
2.  If an error occurs while 
using the USB memory, 
the error message is 
displayed. For details, refer 
to Section 2.6.12 Copying 
Data to/from USB Memory. 
  After clearing the error the 
printer does not resume 
logging automatically.  
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-30 
2.6.9 System Mode 
 
 
 
 
 
 
 
 
 
 
 
 
How to enter the System Mode 
 
 
 
 
 
 
The System Mode consists of the following menus.  
DIAG. 
Used to check and print the printer system information and 
maintenance counter status. 
PARAMETER SET (⇒ Section 2.6.2) 
Used to set the parameters for each printer function. 
ADJUST SET (⇒ Section 2.9) 
Used to fine adjust the print position, cut position, print tone, 
etc.  
TEST PRINT (⇒ Section 2.8) 
Used to perform print tests.  
SENSOR ADJUST  
Used to check the sensor statuses and set each sensor. 
RAM CLEAR  
Used to perform a RAM clear.  DO NOT USE this menu. 
INTERFACE (⇒ Section 2.6.10) 
Used to set the interface parameters. 
BASIC (⇒ Section 2.6.4) 
Used to set the function of basic program when it is loaded to 
the printer. 
FOR FACTORY  
Used for an in-process inspection.  DO NOT use this menu. 
RFID  
Used to set RFID related parameters. (see Installation Manual 
in each RFID kit) 
RTC (⇒ Section 2.6.11) 
Used to set the date and time of the real time clock, enable or 
disable the low battery check, and choose a real time renewal 
timing. 
Z-MODE (⇒ Section 2.6.5) 
Same as BASIC 
USB MEMORY (⇒ Section 2.6.12) 
Used to copy data to/from USB memory.  
RESET 
Used to reset the printer. 
 
 
Power OFFSystem Mode 
Power ON while holding down 
[FEED]&[PAUSE]  
Power ON while holding down 
[MODE]   
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-31 
2.6.10 Interface Setting 
 
 The Interface menu allows configuring printer interface parameters.  
The following table shows the contents of the Interface menu. 
 
Contents of the Interface Menu  
Menu Sub menu  Parameter 
NETWORK LAN/WLAN Interface 
 SNMP 
   SETTING 
   BASIC INFORMATION 
   IP ADDRESS 
   GATEWAY ADDRESS 
   SUBNET MASK 
   SOCKET PORT 
   PORT NUMBER 
   DHCP 
    DHCP CLIENT ID 
    DHCP HOST NAME 
   WLAN STANDARD 
   WLAN MODE 
   DEFAULT KEY 
   802.11B CHANNEL 
   802.11B BAUD 
   802.11G CHANNEL 
   802.11G BAUD 
   WINS 
   WINS ADDRESS 
   LPR 
 USB   
 RS-232C SPEED 
   DATA LENGTH 
   STOP BIT 
   PARITY 
   CONTROL 
 CENTRO. ACK/BUSY 
   INPU PRIME 
    PLUG & PLAY 
 
SYSTEM MODE  
TEST PRINT 
SENSOR ADJUST 
RAM CLEAR 
INTERFACE  
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-32 
2.6.10 Interface Setting 
(Cont.) 
 
 
2.6.10.1  Network Setting 
 
(1) LAN/WLAN 
 
•  OFF  LAN and Wireless LAN are disabled.  
• ON (AUTO)
 Automatically selected. 
•  ON (LAN)  LAN is enabled. 
•  ON (WLAN)  Wireless LAN is enabled. 
 
 
(2) SNMP 
 
•  OFF  SNMP is disabled. 
• ON
  SNMP is enabled. 
 
 
(3) BASIC INFORMATION 
The following information is displayed.  
 
IP Address 
Gateway address 
Subnet mask 
Socket port status 
Socket port number 
 
 
(4) IP ADDRESS  
Set the IP address.  
 
 
 
 
(5) GATEWAY ADDRESS 
  Set the gateway address.  
 
 
 
 
(6) SUBNET MASK 
  Set the subnet mask. 
 
 
 
 
(7) SOCKET PORT 
  Select whether to enable or disable the socket port.  
•  OFF  Socket port is disabled. 
•  ON  Socket port is enabled. 
 
 
192 020 168 010 
192 020 168 010 
255 255 255 000  
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-33 
2.6.10 Interface Setting 
(Cont.) 
 
 (8) PORT NUMBER 
  Set the port number.  
 
 
 
 
 
 
 
 
 
 
(9) DHCP 
  Select whether to enable/disable DHCP. 
 
• OFF  DHCP is disabled. 
•  ON  DHCP is enabled. 
 
 
(10) DHCP CLIENT ID 
  Select ASCII or HEX for setting DHCP Clie  nt ID. 
 
•  ASCII  DHCP client ID is entered with ASCII code. → c 
•  HEX  DHCP client ID is entered with Hex. code. → d 
 
c  When ASCII is selected: 
  Enter 64 characters with ASCII code. 
 
d  When HEX is selected: 
  Enter 64 characters with Hex. code. 
 
 
(11) DHCP HOST NAME 
Enter 32 characters with ASCII code. 
 
 
(12) WLAN STANDARD 
 
• 11b/g
 
• 11b 
• 11g 
 
65535 
00000 
65534 
00001  
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-34 
2.6.10 Interface Setting 
(Cont.)
 
 
 (13) WLAN MODE Set the connection mode and authentication in reference to the 
following table.  
 
ADHOC     OFF 
      WEP40 
      WEP104 
INFRA OPEN     OFF 
        WEP40 
        WEP104 
  SHARED     WEP40 
        WEP104 
  802.1x OPEN SYSTEM TLS WEP40 
        WEP104 
      TTLS WEP40 
        WEP104 
      LEAP WEP40 
        WEP104 
      PEAP WEP40 
        WEP104 
      MD5 WEP40 
        WEP104 
      EAP-FAST WEP40 
        WEP104 
    SHARED KEY EAP-MD5 WEP40 
        WEP104 
    NETWORK EAP WEP40 
        WEP104 
  WPA OPEN TLS   
      TTLS   
      LEAP   
      PEAP   
      EAP-FAST   
    NETWORK EAP   
  WPA-PSK      
  WPA2 OPEN SYSTEM TLS   
      TTLS   
      LEAP   
      PEAP   
      EAP-FAST   
    NETWORK EAP   
  WPA2-PSK      
 
  
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-35 
2.6.10 Interface Setting 
(Cont.)
 
 
 
 
 (14) DEFAULT KEY 
Select a WEP key.  
 
 
 
 
 
 (Default: 1) 
 
(15) 802.11b CHANNEL 
Select a channel for 802.11b WLAN.  
 
 
 
 
 
 (Default: 1) 
 
(16) 802.11b BAUD 
Select a baud rate for 802.11b WLAN.  
 
• 11M
 
• 5.5M 
• 2M 
• 1M 
 
 
(17) 802.11g CHANNEL 
Select a channel for 802.11g. WLAN.  
 
 
 
 
 
 (Default: 1) 
 
(18) 802.11g BAUD 
Select the baud rate for 802.11g WLAN.  
 
• 54M
 
• 48M 
• 36M 
• 24M 
• 18M 
• 12M 
• 9M 
• 6M 
• 11M 
• 5.5M 
• 2M 
• 1M 
 
4 
1 
14 
1 
13 
1  
						

							2. PRINTER SETUP ENGLISH VERSION EO1-33094  
2.6 Printer Setting
 
E2-36 
2.6.10 Interface Setting 
(Cont.) 
 
 
 
 
 
 
  
(19) WINS 
 
• OFF  WINS is disabled. 
•  ON (MANUAL)  WINS is enabled. (Manual) 
•  ON (DHCP)  WINS is enabled. (DHCP) 
 
 
(20) WINS ADDRESS 
The WINS address is displayed.  
 
 
(21) LPR 
 
•  OFF  LPR is disabled.  
• ON
   LPR is enabled. 
 
 
 
 
2.6.10.2  USB 
 
(1) USB SERIAL ID 
 
• OFF
  USB serial ID is disabled.  
•  ON   USB serial ID is enabled. 
 
 
 
 
2.6.10.3  RS-232C 
 
(1) SPEED 
 
• 2400 bps 
• 4800 bps 
• 9600 bps
 
• 19200 bps 
• 38400 bps 
• 115200 bps