Toshiba Bex4t2g Manual

							APPENDIX 1  MESSAGES AND LEDS ENGLISH VERSION EO1-33094  
APPENDIX 1  MESSAGES AND LEDS
 
EA1- 2 
LED IndicationPrinter Status Restoration by RESTART key 
Acceptance of 
Status Request/Reset Command No. LCD Message 
ONLINE ERROR  Yes/No Yes/No 
20 Display of error message  
(See Notes.)     A command error has occurred  
while analyzing the command.   Yes  Yes 
21 POW ER FAILURE 
   A power failure has occurred.  No  No 
22 EEPROM ERROR    Data cannot be read from/written to  
a backup EEPROM properly  No  No 
23 SYSTEM ERROR 
   
When the following abnormal  
operations are performed, a  
system error occurs: 
(a) Command fetch from an  incorrect address. 
(b) Access to word data at an  incorrect address. 
(c) Access to long-word data 
at an 
incorrect address. 
(d) Access to the area of 
80000000H to FFFFFFFFH in  
the logic space in user mode. 
(e) An undefined instruction in an 
area other than a delay slot 
was decoded. 
(f)  An undefined instruction in a 
delay slot was decoded. 
(g) An instruction to rewrite a 
delay slot was decoded.  No  No 
24 DHCP CLIENT INIT…  
   DHCP Client is being initialised.  
(Only when the DHCP is enabled.)  -----  ----- 
25 RFID WRITE ERROR 
   
The printer did not succeed in  
writing data onto an RFID tag after 
having retried the specified number  
of times.  Yes  Yes 
26 RFID ERROR 
   The printer cannot communicate  
with the RFID module.  No  Yes 
27 LOW BATTERY 
   The voltage of the Real Time Clock  
Battery is low.  No  Yes 
28 INPUT PASSWORD 
   The printer is waiting for a  
password to be entered.   No  No 
29 PASSWORD INVALID  
Please Power OFF 
   A wrong password was entered  
three consecutive times.   No  No 
30 INTERNAL COM ERR 
   A hard error occurred in internal  
serial interface.  No  No 
      
   
 
NOTE:  When an error message listed above appears on the  LCD display please refer to Section 5 
TROUBLESHOOTING  for a solution.  
    
						

							APPENDIX 1  MESSAGES AND LEDS ENGLISH VERSION EO1-33094  
APPENDIX 1  MESSAGES AND LEDS
 
EA1- 3 
 
NOTES:    If an error is found in a command received, up to 4 2 bytes of the erroneous command, starting from the  
command code, will be displayed.  (However, [LF] an d [NUL] will not be displayed.) 
 
 
  
Example 1 
[ESC]PC001;0 A
00,0300,2,2,A,00,B[LF][NUL]  
  Command error  
The following message appears.          
Example 2 
[ESC]T20 G
30[LF] [NUL]  
  Command error  
The following message appears.          
Example 3 
[ESC]PC002;0100,0300,15,15,A,00,00,J0101,+000000000 A
,Z10,P1[LF] [NUL] 
         Command error 
The following message appears.              When the error is shown, “? (3FH)” appears for char acter codes other than 20H to 7FH and A0H to 
DFH. 
  For details, please refer to the  B-EX4T/EX6T Series External Equipment Interface Specification.  
SYNTAX ERROR 
PC001;0A00,0300,2,2,A  
,00,B
 
SYNTAX ERROR 
T20G30 
SYNTAX ERROR 
PC002;0100,0300,15,15 
,A,00,00,J0101,+00000   
						

							APPENDIX 2  INTERFACE ENGLISH VERSION EO1-33094  APPENDIX 2  INTERFACE
 
EA2- 1 
APPENDIX 2  INTERFACE 
                
  USB interface (Standard) 
Physical Layer:  Conforming to V2.0 Full speed  
Transfer type:  Control transfer, Bulk transfer  
Transfer rate:  Full speed (12M bps)  
Class:  Printer class 
Number of ports:  1  
Power source:  Self power  
Connector:  Type B   
Pin No.  Signal 
1  VCC 
2  D- 
3  D+ 
4  GND 
   
 LAN (Standard) 
Physical Layer:  IEEE802.3  10BASE-T/100BASE-TX   
Number of ports:  1  
Connector:  RJ-45 
LED status:  Link LED, Activity LED  
                 
LAN cable:  10BASE-T: UTP category 3 or category 5 
  100BASE-TX: UTP category 5  
Cable length:  Segment length  Max. 100 m     
     
NOTE:  
To prevent radiation and reception of electrical no ise, the interface cables must meet the following requirements: 
   In case of a parallel interface cable or serial int erface cable, fully shielded and fitted with metal  or metallised 
connector housings. 
   Keep as short as possible. 
   Should not be bundled tightly with power cords. 
   Should not be tied to power line conduits . 
   A parallel interface cable to be used should confor m to IEEE1284. 
 Series B Plug 
NOTE:  
When  a  generally-used  twisted  pair  Ethernet  (TPE)  o r  UTP  cable  is  used,  a  communication  error 
may occur depending on your operating environment.   In such case, you may be requested to use a 
shielded twisted pair cable.  
 
Link LED (Green) 
Activity LED (Orange) 
LED  LED Status  LAN status 
ON  10Mbps link or 100Mbps link is detected. Link 
OFF  No link is detected. *  Communication  cannot  be  made  while  
the Link LED is off.  
ON  Communicating Activity 
OFF  Idle    
						

							APPENDIX 2  INTERFACE ENGLISH VERSION EO1-33094  APPENDIX 2  INTERFACE
 
EA2- 2 
  Serial interface (Option: B-EX700-RS-QM-R) 
Type:  RS-232C  
Communication mode: Full duplex  
Transmission speed:  2400 bps, 4800 bps, 9600 bps, 1 9200 bps, 38400 bps, 115200 bps 
Synchronization:  Start-stop synchronization  
Start bit:  1 bit  
Stop bit  1 bit, 2 bit 
Data length:  7 bit, 8 bit  
Parity:  None, EVEN, ODD  
Error detection:  Parity error, Framing error, Overr un error 
Protocol:  Unprocedure communication  
Data input code:  ASCII  code,  European  character  8  b it  code,  graphic  8  bit  code,  JIS8  code, 
Shift JIS Kanji code, JIS Kanji code 
Receive buffer:  1M byte  
Connector:   
Pin No.  Signal 
1  N.C 
2  TXD (Transmit Data) 
3  RXD (Received Data) 
4  DSR (Data Set Ready) 
5  SG (Signal Ground) 
6  DTR (Data Terminal Ready) 
7  CTS (Clear to Send) 
8  RTS (Request to Send) 
9  N.C 
   
  Parallel interface (Centronics) (Option: B-EX700-CE N-QM-R) 
Mode:  Conforming to IEEE1284  
Compatible mode (SPP mode), Nibble mode 
Data input method:  8 bit parallel  
Control signal:                   
 
Data input code:  ASCII code 
European 8 bit code  
Graphic 8 bit code 
JIS8 code  
Shift JIS Kanji code  
JIS Kanji code 
Receive buffer:  1MB 
SPP Mode  Nibble Mode  ECP Mode 
nStrobe  HostClk  HostClk 
nAck  PtrClk  PeriphClk 
Busy  PtrBusy  PeriphAck 
Perror  AckDataReq  NAckReverse 
Select  Xflag  Xflag 
nAutoFd  HostBusy  HostAck 
nInit  nInit  nReverseRequest 
nFault  nDataAvail  nPeriphRequest 
nSelectIn  IEEE1284Active  IEEE1284Active 
1
5
6
9
  
						

							APPENDIX 2  INTERFACE ENGLISH VERSION EO1-33094  APPENDIX 2  INTERFACE
 
EA2- 3 
Connector: 
Signal PIN  No.  SPP Mode  Nibble Mode  ECP Mode 
1  nStrobe  HostClk  HostClk 
2  Data 1  Data 1  Data 1 
3  Data 2  Data 2  Data 2 
4  Data 3  Data 3  Data 3 
5  Data 4  Data 4  Data 4 
6  Data 5  Data 5  Data 5 
7  Data 6  Data 6  Data 6 
8  Data 7  Data 7  Data 7 
9  Data 8  Data 8  Data 8 
10  nAck  PtrClk  PeriphClk 
11  Busy  PtrBusy  PeriphAck 
12  PError  AckDataReq  nAckReverse 
13  Select  Xflag  XFlag 
14  nAutoFd  HostBusy  HstAck 
15  NC  NC  NC 
16  0V  0V  0V 
17  CHASSIS GND  CHASSIS GND  CHASSIS GND 
18  +5V (For detection)  +5V (For detection)  +5V (For  detection) 
19  TWISTED PAIR GND(PIN1)  TWISTED PAIR GND(PIN1)  TWISTED PAIR GND(PIN1) 
20  TWISTED PAIR GND(PIN2)  TWISTED PAIR GND(PIN2)  TWISTED PAIR GND(PIN2) 
21  TWISTED PAIR GND(PIN3)  TWISTED PAIR GND(PIN3)  TWISTED PAIR GND(PIN3) 
22  TWISTED PAIR GND(PIN4)  TWISTED PAIR GND(PIN4)  TWISTED PAIR GND(PIN4) 
23  TWISTED PAIR GND(PIN5)  TWISTED PAIR GND(PIN5)  TWISTED PAIR GND(PIN5) 
24  TWISTED PAIR GND(PIN6)  TWISTED PAIR GND(PIN6)  TWISTED PAIR GND(PIN6) 
25  TWISTED PAIR GND(PIN7)  TWISTED PAIR GND(PIN7)  TWISTED PAIR GND(PIN7) 
26  TWISTED PAIR GND(PIN8)  TWISTED PAIR GND(PIN8)  TWISTED PAIR GND(PIN8) 
27  TWISTED PAIR GND(PIN9)  TWISTED PAIR GND(PIN9)  TWISTED PAIR GND(PIN9) 
28  TWISTED PAIR GND(PIN10)  TWISTED PAIR GND(PIN10) TWISTED PAIR GND(PIN10) 
29  TWISTED PAIR GND(PIN11)  TWISTED PAIR GND(PIN11) TWISTED PAIR GND(PIN11) 
30  TWISTED PAIR GND(PIN31)  TWISTED PAIR GND(PIN31) TWISTED PAIR GND(PIN31) 
31  nInit  nInit  nReverseRequest 
32  nFault  NDataAvail  nPeriphRequest 
33  0V  0V  0V 
34  NC  NC  NC 
35  NC  NC  NC 
36  nSelectIn  IEEE1284Active  IEEE1284Active 
 
 
       IEEE1284-B Connector   
						

							APPENDIX 2  INTERFACE ENGLISH VERSION EO1-33094  APPENDIX 2  INTERFACE
 
EA2- 4 
  Wireless LAN (Option: B-EX700-WLAN-QM-R) 
Standard:  Conforming to IEEE802.11b, and IEEE802.11 g 
Client protocol:  TCP/IP, Socket, LPD (LLPR), DHCP/W INS, HTTPD (SNMP) 
Print protocol:  Socket communication/LPR  
Security protocol:  WEP (64 bits/128 bits) or AES, T KIP (only when using WPA, WPA-PSK) 
Shared key (for WEP), PSK, PEAP, TLS, TTLS, MD5, LE AP, EAP-FAST 
Antenna:  Built-in   
Parameter setting:  via USB, LAN, WLAN, RS-232C, Par allel 
Default IP address:  192.168.10.21 
Default subnet mask:  255.255.255.0 
Certification:  Wi-Fi, CCX V3, V4          
   
  USB Host interface (Option: B-EX700-RTC-QM-R) 
Physical Layer:  Conforming to V2.0 Full speed  
Transfer type:  Control transfer, Bulk transfer 
Transfer rate:  Full speed (12M bps)  
Number of ports:  1  
Power supply:  50mA output 
Connector:  Type A   
      
NOTE: 
MAC address of the Wireless LAN module will be nece ssary when setting the MAC address filtering function of an 
access point.  Please ask a service person of your nearest TOSHIBA TEC service representative.   
						

							APPENDIX 2  INTERFACE ENGLISH VERSION EO1-33094  APPENDIX 2  INTERFACE
 
EA2- 5 
  Expansion I/O Interface (Option: B-EX700-IO-QM-R) 
Input Signal  IN0 to IN5  
Output Signal  OUT0 to OUT6  
Connector   FCN-781P024-G/P or equivalent   
(External Device Side)  
Connector  FCN-685J0024 or equivalent  
(Printer Side)                           
Input Circuit   
 
Output Circuit   
 
 
Operating environment  Temperature: 0 to 40  °C 
  Humidity: 20 to 90% (No Condensation) 
 
   
Pin  Signal  I/O  Function  Pin  Signal  I/O  Function 
1  IN0  Input  FEED  13  OUT6  Output   
2  IN1  Input  PRINT  14  N.C.  -----   
3  IN2  Input  PAUSE  15  COM1  Common (Power)   
4  IN3  Input    16  N.C.  -----   
5  IN4  Input    17  N.C.  -----   
6  IN5  Input    18  N.C.  -----   
7  OUT0  Output  FEED  19  N.C.  -----   
8  OUT1  Output  PRINT  20  N.C.  -----   
9  OUT2  Output  PAUSE  21  COM2  Common (Ground)  
10  OUT3  Output  ERROR  22  N.C.  -----   
11  OUT4  Output    23  N.C.  -----   
12  OUT5  Output  POWER ON 24  N.C.  -----   
N.C.: No Connection    
						

							APPENDIX 2  INTERFACE ENGLISH VERSION EO1-33094  APPENDIX 2  INTERFACE
 
EA2- 6 
  RFID (Option) 
 B-EX700-RFID-H1-QM-R 
Module:  TagSysm MEDIO S002 /S003 (Not included in t his optional kit.) 
Frequency:  13.56MHz  
Output:  200 mW  
Available RFID tag:  TagSys C210, C220, C240, C320 I -Code, Tag-it, ISO15693 
Antenna:  RF antenna is not included in this optiona l kit. 
    
						

							APPENDIX 3  PRINT SAMPLES ENGLISH VERSION EO1-33094  
APPENDIX 3  PRINT SAMPLES
 
EA3- 1 
APPENDIX 3  PRINT SAMPLES 
  Font 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
   
   
 
 
 
   
   
 
 
 
 
                           
						

							APPENDIX 3  PRINT SAMPLES ENGLISH VERSION EO1-33094  
APPENDIX 3  PRINT SAMPLES
 
EA3- 2 
APPENDIX 3  PRINT SAMPLES (Cont.) 
  Bar codes 
JAN8, EAN8  MSI         
Interleaved 2 of 5  CODE39 (Standard)        
NW7  JAN13, EAN13 
      
UPC-E  EAN13+2 digits 
       
EAN13+5 digits  CODE128        
CODE39 (Full ASCII)  CODE93         
UPC-E+2 digits  UPC-E+5 digits        
EAN8+2 digits  EAN8+5 digits        
UPC-A  UPC-A+2 digits