Tone Commander T6220t-Tsg User Manual

48Tone Commander 6220T-TSG User Manual
Personal Ringing Options   ________________
Ringing Tone
Your telephone has eight distinct ringing tones available. In
environments with multiple terminals, unique ringing tones can help
identify ringing stations. The selected ringing tone is used for all call
appearances.
From the User Options menu, select RING.
(Setup → USER
 → RING)
Select the TONE option.
Press a dial pad key (1-8) to select a ringing tone and hear a
sample of the tone.
When you have chosen a...

Tone Commander 6220T-TSG User Manual49
Ringing Control for Individual Call Appearances
You can control the audible ringing at your telephone for each call
appearance.
Call appearances set to Always will ring immediately. Use this setting
for your primary call appearances.
Never completely disables ringing on the call appearance. Use this
selection for monitored call appearances that are normally answered
elsewhere.
Wait delays ringing at your telephone for 2 to 7 ringing cycles (6
seconds per cycle). Use...

50Tone Commander 6220T-TSG User Manual
Call Preference Options   __________________
(National ISDN only)
Call Preference determines what happens when you lift the handset.
For Lucent 5ESS Custom ISDN service, Call Preference is controlled
by the network.
RING preference will automatically select the oldest audibly ringing call
appearance; if there is no ringing call appearance, an idle one is
automatically selected. Call appearances that are in an alerting state,
but are not audibly ringing (refer to the...

Tone Commander 6220T-TSG User Manual51
Handset Configuration   ___________________
Preset Volume Levels
The preset handset receive volume level may be set to provide higher
preset levels for hearing impaired users. The telephone is reset to
preset volume levels whenever a call is originated or answered.
Receiver volume levels set with the Vol keys are used only for the
duration of a call.
From the User Options menu, select VOICE.
(Setup → USER
 → More
4 → VOICE)
Select VOLUME.
The display will show the...

52Tone Commander 6220T-TSG User Manual
Press the Done key to return to the User Options menu or the
Setup key to exit Setup Mode.Done
CONTRAST [{{{{{   ]
 (-)   (+) 

Tone Commander 6220T-TSG User Manual53
Setting a Call Log Password   ______________
You can set a password to prohibit unauthorized entry into your Call
Log.
From the User Options menu, select PASSWD.
(Setup → USER
 → More
4 → PASSWD)
If a password is currently set, the display will prompt you to
enter your password prior to making changes.
Creating/Changing Your Password
Select SET.
Enter a new 4-digit password with the dial pad.
If you need to make corrections, select 
ÅBKSP (backspace)
to delete the...

54Tone Commander 6220T-TSG User Manual
Press the Done key to return to the User Options menu or the
Setup key to exit Setup Mode.
Removing the Password
Select CLEAR.
“PASSWORD CLEARED” will be displayed to confirm that the
password has been removed.
Press the Done key to return to User Options menu or the
Setup key to exit Setup Mode.
What to do if you lose your password
Contact your system administrator or call Tone Commander technical
support at (800) 524-0024 in the event you misplace your password....

Tone Commander 6220T-TSG User Manual55
Troubleshooting
Inoperable Telephone Recovery Procedures
Whenever a telephone is unable to operate normally or remains in
a particular state with no escape, accomplish the following:
1.  Press SETUP, the SETUP Menu should be displayed. This
response indicates that there is power to the telephone, and its
microprocessor is operating. Proceed to Step 5. If there is no
display, proceed to Step 2.
2.  Reseat the eight pin connectors of the telephone mounting cord at
the...

56Tone Commander 6220T-TSG User Manual
Layer 3 does not initialize:
•  Verify that the correct SPID number is programmed.
•  Verify with the serving telco that they have not changed from a
customized to a universal SPID format.
•  Verify with the serving telco that they have not changed their
office to a new area code (some SPID formats include the area
code).
•  Enter the correct SPID or SPID format.
With full initialization, proceed to the following steps.
Verify operation of the telephone by...

Tone Commander 6220T-TSG User Manual57
Telephone Configuration Troubleshooting
CA/DN troubleCheckFix
Inbound calls to a
specific line cause the
LED to flash, but there is
no audible ringing.>SETUP >USER
>RING >CONTROL
>Select line>ALWAYS
A specific line is
selected that is
supposed to have dial
tone, but there isn’t any.>SETUP >INSTL
>KEYS
>Select line key>CA/DN
General usageCheckFix
All inbound calls appear
on CA1. Outbound calls
cannot be made.>SETUP >INSTL
>MORE >MODE>CACH
Ringing calls are not...