System 25 Fax ATTendant System Implementation And Switch Manual

Overview and Testing
7.
8.
9.
10.
11.
12.
13.
14.
15.
Press [ F6 ] (CANCEL) to continue.
The Voice Equipment window reappears.
Press [ 
F2 ] (CHGSTATE).
The Change State of Voice Equipment form appears.
In the New State: field, enter inserv or i and press [ ENTER ¿ ¿ ].
In the 
Equipment: field, enter card or ca and press [ ENTER ¿ ¿ ].
In the 
Equipment Number: field, enter all and press [ ENTER ¿ ¿ ].
In the 
Change Immediately? field, enter yes or y and press [ F3 ] (SAVE).
A Command Output window...

Overview and Testing
Verifying Voice Channel Extensions
/ NOTE:
The analog ports assigned to voice channels must be administered as VMS
ports on the System 25 before running this test. See Chapter 3 for
administration procedures for these ports.
To verify the extensions assigned to voice channels, follow these steps:
1.At the Voice System Administration menu, select System Monitor and
press [ ENTER ¿ ¿ ].
The System Monitor - Voice Channels window appears.
System Monitor - Voice Channels
Calls...

Overview and Testing
5.Repeat Steps 2 through 4 until all extensions have been verified.
If the extension assignments do not match those already recorded on FORM
A, you may either change the connections between the lVP4/6 boards and the
wall outlet jacks, or you may notify the Switch Administrator of the changed
assignments. The optimum course of action depends on whether the Switch
Administrator has already made use of the extension assignments for the rest
of the administration that must be done on the...

Overview and Testing
Changing the Maintenance Mailbox Password
/ NOTE:
This procedure is necessary only for fax channel testing. (See the next
procedure.)
To reduce the risk of unauthorized access, AT&T has changed the default
passwords for the Maintenance (9998) mailbox to [ # ] . The [ # ] prevents anyone from
accessing the mailboxes.
When adding FAX Attendant to an existing AUDIX Voice Power system, a new
password should already have been assigned to the Maintenance Mailbox. Obtain
this password from...

Overview and Testing
Verifying Fax Channel Extensions
/ NOTE:
The analog ports assigned to fax channels must be administered on the
System 25 before running this test. See Chapter 3 for administration
procedures for these ports.
Test the fax channel extensions by placing all fax channels out of service. Test each
fax channel individually by placing it into service alone.
To verify the extensions assigned to fax channels, follow these steps:
1.
2.
3.
4.
5.
6.
7.
At the Voice System Administration menu,...

Overview and Testing
8.
9.
10.
11.
12.Place
a.
b.
c.
d.
e.
one fax channel in-service for testing:
In the New State field, enter i for in-service (INSERV).
In the 
Fax Equipment field, enter ch for channel.
In the Fax Equipment Number field, enter the channel to be tested.
Leave the Change Immediately? field blank and press [ 
F3 ] (SAVE).
Verify that all fax channels are in the MANOOS state except for the
channel being tested. The channel being tested should be in the
INSERV state.
Dial any of the...

Overview and Testing
13.After the last fax channel has been tested, place all fax channels back in-
service:
a.In the New State field, enter i for INSERV.
b.In the Fax Equipment field, enter ca for card.
c.In the Fax Equipment Number field, enter all.
d.Leave the Change Immediately? field blank and press [ F3 ] (SAVE).
e.Verify that ail fax channels are in the INSERV state.
14.Press [ F6 ] (CANCEL) repeatedly until the AUDIX Voice Power/FAX Attendant
menu appears.
1-25 

Overview and Testing
Resetting the Maintenance Mailbox Password
If you assigned a temporary password to the Maintenance Mailbox, you must reset
the password to [ 
# ] after testing the fax channel extensions. If you did not assign a
temporary password to the Maintenance Mailbox, skip the remainder of this
procedure.
To change the password for the Maintenance Mailbox, follow these steps:
1.At the AUDIX Voice Power/FAX Attendant main menu, move the cursor to
Subscriber Administration and press [ ENTER ¿ ¿...

FAX Attendant Initial Implementation
2
The major initial implementation functions for FAX Attendant are:
nAssigning services to channels
nAdministering switch interface parameters
nAdministering FAX Attendant system parameters
Assigning Services to Channels
When FORM A is complete and you have reviewed it, enter the service assignment
information into FAX Attendant.
The System 25 indicates to FAX Attendant whether a call is internal direct, external
direct, or coverage. When a channel has Fax Response as...

FAX Attendant Initial Implementation
Assigning Services to Channels
To assign services to channels, follow these steps:
1.Log on as maint.
2.At the Integrated Solution Maintenance menu, move the cursor to
Technician Maintenance and Press [ ENTER ¿ ¿ ].
The Technician Maintenance menu appears.
3.At the Technician Maintenance menu, move the cursor to Voice System
Administration and press [ ENTER ¿ ¿ ].
The Voice System Administration menu appears.
Move to an item using arrow keys and hit Enter to select....