Smarthome Fx 416 Instruction Manual

KCE Technology Corporation45 Playback of Alarm/Timer SettingYou may verify the alarm time that you have programmed for the extension.
How:
To play back
      JKL
5
  GHI
4DEF
3ABC
21
  #
  beep
beepDEF
3
  1
    #
   1. Lift the handset
   2. Validate the password if a password has been programmed in, otherwise go to step 3
   3. Dial [*3 X * #], where X is the group number
   4. Wait for confirmation tone
   5. Hang up 

KCE Technology Corporation46 Setting Call Waiting FunctionEach extension can be individually programmed to turn Call Waiting function On, Off, or Off
Once Only.  Call Waiting On is the default setting.
How:
To turn on (Call Waiting function enabled)
      JKL
5
  GHI
4DEF
3ABC
21
  #
  beep
beepGHI
41
  1
  #
  beep
beep      1. Lift the handset
   2. Validate the password if a password has been programmed in, otherwise go to step 3
   3. Dial [*411#]
   4. Wait for confirmation tone
   5. Hang up
To...

KCE Technology Corporation47 Caller IDThe FX-416 comes with Caller ID feature that allows you to identify the caller’s phone number at
each extension with a Caller ID telephone or Caller ID display unit.  To use Caller ID function,
you must subscribe to the Caller ID service from your local telephone company.
Voice Caller IDVoice Caller ID is a special feature that the FX-416 will announce the caller’s phone number
when you pick up the call.  After the announcement of the Caller ID, you have about 5...

KCE Technology Corporation48  Caller’s NameThe FX-416 provides the capability of identifying the Caller’s Name.  To obtain the Caller’s
Name, the FX-416 will prompt caller for his/her name and record it before connecting the
incoming call to the extension. After the announcement of the caller’s name, you have about 5
seconds to decide whether you would like to talk to the caller or hang up the call.  Once the
Caller’s Name feature is enabled, then the Caller ID is automatically disabled.
How:
To enable...

KCE Technology Corporation49 Setting the Number of RingsThe number of the rings before the call going to Busy/No Answer Transfer mode is user
programmable.  You may adjust the number of the rings to fit your own preference.  The number
of rings that you can set is from 1 to 9.
How:
To set the number of rings
      JKL
5
  GHI
4DEF
3ABC
21
  #
  beep
beepGHI
4MNO
6
  MNO
6
  #
  beep
beep      1. Lift the handset
   2. Validate the password if a password has been programmed in, otherwise go to step 3...

KCE Technology Corporation50 Setting Ring-Back ModeRing-Back is for reminding user that there is a call on hold.  The default setting of the Ring-Back
mode is ON for every extension.
How:
To turn on (Ring-Back enabled)
      JKL
5
  GHI
4DEF
3ABC
21
  #
  beep
beepGHI
4TUV
8
  1
  #
  beep
beep      1. Lift the handset
   2. Validate the password if a password has been programmed in, otherwise go to step 3
   3. Dial [*481]
   4. Wait for confirmation tone
   5. Hang up
To turn off (Ring-Back disabled)...

KCE Technology Corporation51 System Programming
You can program the FX-416 system to fit your requirements.  This section describes all
programming options available for system setup.  All the settings programmed are system-wide.
All the functions in this section can also be accessed from the remote (dialing in through a CO line
from outside) if you have supervisor password.
Setting New Supervisor PasswordThere is no preset supervisor password.  If there is a need to protect the system setup from...

KCE Technology Corporation52 Canceling Extension PasswordPassword feature may be disabled if the password protection is not needed.  The supervisor has
authority to cancel any extension password.
How:
   JKL
5
  GHI
4DEF
3ABC
21
  #
  beep
beepJKL
5
  ABC
2OPER
01
    #
  beep
beep   1. Lift the handset
   2. Validate the password (supervisor password, e.g. 4321)
   3. Wait for confirmation tone, then hear system dial tone
   4. Dial [*5 201 ** #] (e.g. extension 201)
   5. Wait for confirmation tone...

KCE Technology Corporation53 Changing Supervisor PasswordValidate the password first then enter a new password.
How:
      JKL
5GHI
4DEF
3ABC
21
  #
  beep
beepJKL
5ABC
2MNO
6WXY
9
  1ABC
2DEF
3GHI
4
  1ABC
2DEF
3GHI
4
  #
  beep
beep  1. Lift the handset
   2. Validate the password (supervisor password, e.g. 4321)
   3. Wait for confirmation tone, then hear system dial tone
   4. Dial [*5 269 *], denoting supervisor access
   5. Dial [*5xxxx*], xxxx represents the new password (e.g. 1234)
   6. Dial...

KCE Technology Corporation54 Setting Voice Announcement to Day/Night ModeThe system will announce the Primary and Secondary messages according to the time set by the
user.  The default starting time for Primary message announcement is 08:00 and default starting
time for Secondary message announcement is 17:00.
How:
To set voice announcement to Day/Night Mode
   JKL
5
  GHI
4DEF
3ABC
21
  #
  beep
beepMNO
6
  OPER
0
  #
  beep
beep   1. Lift the handset
   2. Validate the password if a password has been...