Singer Serger Professional 5 Manual

 
 7. Thread the hole in the Upper  Looper from front to back k.  Pull about 4  
                 inches of thread through the loope r and place to the back of the  
                 throat plate. 
  
 
 
 
 
 
 
 
 
 
 
 
 
 

 
   
  
 4. While holding the thread firmly, pu ll the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
   
  5. Turn the handwheel toward you unt il the lower looper extends 5-10mm  
       (approximately ½ inch ) from the needle plate edge.  
 
  6. Thread the looper area of the mach ine following the red color coded  
       thread guides 4-10.  
 
 
 
  7. Place the thread slighty from left and  
      to the ri ght of threading guide  f. 
 
 
 
 
  8. Place the thread slightly from the...

 
   
 Five-Thread Safety Stitch Narrow page 10  
 10. Thread the looper eye (A)  from front to back.  Pull about 4 inches of thread. 
                 Position thread into V cutout (B) on thr eader.  Firmly hold thread tail with left   
                  hand and pull Threader lever (C) up into place (D).  
 
 
 
 
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
     
 
 
 
 
 
 
NOTE: Make sure the Upper Looper thread is 
behind the Lower Looper thread. 
Threader Lever 
“V” cutout   

 
 
4. Turn the hand wheel toward you until  the Chainstitch Looper extends out   
                10mm (approximately ½ inch)  from the needle plate edge. 
 
  
 
 
 
 
 
 
 
 
  5. Thread the looper area of the ma chine following the brown color-coded  
               thread guides 4-11.  Us e the tweezers provided in the accessory case to  
               aid in threading the looper. 
 
  6. Place the thread through threading guide  f and  g. 
 
 
           7. Continue threading guides  h, i , j  and...

 
  5. Before threading the eye of the needle, make sure the thread is behind   
               the thread guide located on the  bottom of the needle clamp. 
 
 
 
 
 
 
  
  
 
 
  
  
  6. Thread the eye of the Right Overedge Needle  k. 
 
 
 
 
 
 

 
  
  3. Thread the top cover thread guide by pulling the thread towards the left until  
              it slips under the guide. T hen pull the thread along the right side of the button   
              as illustrated. 
 
  
 
 
 
 
 
 
  
  4.  While holding the thread firmly, pu ll the thread between the tension disks.   
 
 
 
 
 
 
  
 
 
 
 
  
 
 
  5. Continue to thread point s 4-8.  Slip the thread into the middle slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by...

 
  
  6. Before threading the eye of the needle, make sure the thread is in front of  
               the thread guide located on the bottom  of the needle clamp for the Cover  
                Stitch or Chainstitch. 
 
 
 
  7. Thread the eye of the middle needle  k. 
 
  
 
 
 
 
 
 
 
 
 
 
  
 
 
 
  8. Draw about 4 inches of the thr ead through the needle eye towards the back 
      of the machine.  
  
      9. Place the thread to  the back, under the Presser F oot.  Lower foot and sew....