Singer Serger Professional 5 Manual

 
 
 
 
  
   
  
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                  
 
 
 
 
 
 
 
 
 
 
 
  
 
  3. Thread the top cover thread guide by  pulling the thread towards the left until 
       it slips under the guide.  Then pu ll the thread along the right side of the  
       button as illustrated....

 
   
   
   
 
 
 
  
 7. Thread the hole in the Upper  Looper from front to back k.  Pull about 4  
                 inches of thread through the loope r and place to the back of the  
                 throat plate. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
   
  
 
  
  3. Thread the top cover thread guide by pu lling the thread towards the left until    
                it slips under the guide.  Then pull the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
  4. While holding the thread, firmly  pull the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
   
  5. Turn the handwheel toward you unt il the lower looper extends 5-10mm  
       (approximately ½ inch ) from the needle plate edge.  
 
  6. Thread the...

 
 10. Thread the looper eye (A)  from front to back.  Pull about 4 inches of thread. 
                 Position thread into V cutout (B) on thr eader.  Firmly hold thread tail with left   
                  hand and pull Threader lever (C) up into place (D).  
 
 
   
 
 
 
 
 
 
 
 
 
 
   
 
   
 
 
 
 
 

 
   
  
  3. Thread the top cover thread guide by pulling the thread towards the left until 
       it slips under the guide.  Then pu ll the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
 
 
 
  4. Continue to thread point s 4-8.  Slip the thread into the rear slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the right  slot of the thread guides i and  j.  
 
  
 
 
 
 
 
 
 
 
 
 
 
   
  5....

 
   
  
 
  5. Continue to thread point s 4-8.  Slip the thread into the middle slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the middle  slot of the thread guides i and  j.  
 
  6. Before threading the eye of the needl e, make sure the thread is behind
  
               the thread guide located on the  bottom of the needle clamp. 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
 
 
 
  7. Thread the eye of the Left Overedge Needle  k....

 
   
   
   
   
  
  
                   
 
                                   
Chapter 8:         
        Four-Thread Safety Stitch