Siemens Saturn Iie Epabx General Description Manual

SATURN IIE EPABX 
‘nstallation Procedures A30808X5130-BllO-l-8928 
Issue 1, May 1988 
Table 4.00 SATURN 11E EPABX Orderable Item List (Continued) 
AVAILABLE EQUIPMENT PART NO. 
COMMENTS 
Subscriber Line Module Analog - 
Off-Premises Station (SLMA-0) PCB S30810-Q1739-X- * -8900 Refer to Table 4.18 
Subscriber Line Module Digital 
(SLMD) PCB S30810-Q1724-X- + -8900 
Refer to Table 4.17 
Central Office Trunk (TMBM) PCB S30810-Q414-X- * -8900 
Refer to Table 4.19 
Direct Inward Dialing Trunk (TMIE) 
PCB -....

SATURN IIE EPABX Installation Procedures 
A30808-X5130-BllO-l-8928 
Issue 1, May 1986 
.’ 
Plastic 
Straps 
A4960-1.4117166 Figure 4.00 Basic Cabinet Contalner 
4-3  

SATURN HE EPABX 
hstallation Procedures A30808-X5130-BllO-l-B928 
issue 1, May 1986 
., 
Straps 
Pallet Sleeve 
c 
A49fwl-4/14/86 Figure 4.01 Basic Cabinet Packaging Method Ramp 
4-4  

SATURN IIE EPABX A30808-X5130-BilO-l-8928 
Installation Procedures Issue 1, May 1986 
d. Remove ramp from its packaged location and place 
into position as shown in Figure 4.02. Carefully push 
the cabinet out of position and onto the ramp to un- 
load it. Note, unloading of cabinet is a two-man job. After unloading the cabinet, do not lift it with a fork-lift 
or lifting device since structural damage may occur. 
Each cabinet contains four 360 degree casters to facili- 
tate its movement. Refer to Table...

I 
- 
SATURN IIE EPABX 
Installation Procedures A30808-X5130-BllO-l-8928 Issue 1, May 1986 
Table 4.01 Basic System 
QTY. EQUIPMENT 
Ref. PART NO. 
1 Basic Cabinet Assembly 1. S30805-G5112-X- * -8900 
1 
Power 
Cable Assembly (PSU-basic shelf,LTU,LTUPS, 
-48PSO/l,FDD0/1/2 ) 
Wl C39195A9679Al- * -8900 
1 
Signal Cable Assembly (Basic Shelf - PSU J12) 
w2 C39195&679-A2- * -B900 
1 
Signal Cable Assembly (Basic Shelf - LTUO/1/2) 
w3 C39195-A9679-A3- * -8900 
1 
Signal Cable Assembly (Basic Shelf - FDDO or...

- 
SATURN IIE EPABX A30808-X5130-BllO-l-8928 
Installation Procedures 
Issue 1, May 1986 
i 
Table 4.01 Basic System (Continued) 
3. Replace front and rear panels, if necessary, and move equipment cabinet to its approximate 
final position. 
ADDITIONAL 
EQUIPMENT 
REdUIRED: Per installation-site configuration to meet customer requirements. 
OBSERVATIONS: 
None: the common equipment PCBs and modules equipped with the basic system are already 
in their corresponding positions. 
INSTALLATION 
Pf$ICEDURES:...

- 
SATURN IIE EPABX 
installation Procedures 
’ I 
A30808-X5130-BllO-l-8928 
Issue 1, May 1986 
SATURN Ilt 
! 
P5070.25-worn Figure 4.03 Basic Cabinet (Front View) 
4-8  

SATURN IIE EPABX 
installation Procedures A30808-X5130-BllO-l-8928 
Issue 1, May 1986 
.I 
P5030.3.3/20/86 Figure 4.04 Basic Cabinet (Rear View) 
4-9  

SATURN IlE EPABX Installation Procedures 
A30808-X5130-BllO-l-8928 Issue 1, May 1986 
.’ 
i 
I 
I 
C4996-l-4114166 Figure 4.05 Basic Cabinet Connector Contiguration 
4-10  

I 
SATURN IIE EPABX 
A30808-X5130-BllO-l-8928 
installation Procedures 
Issue 1, May 1986 
r-------- 
Basic 
Cabinet 
LTU 
Shelf 
(256 ports) 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
I 
L----,. 
NOTE: 
Shaded area shows items 
equipped in Main Cabinet. 
0 optional equipment t ’ 318” 
Leveler  Power System Unit Basic 
Shelf 
(224 ports) 
5%” FD DRIVE 
Plain Hex Nut 
Si 
A49631-3127166 Figure 4.06 Basic Cabinet Equipment Configuration and Securing Procedures 
4-11