Sharp Ux Cl220 Plain Paper Fax And 2 4 Ghz Cordless Phone Wi Operation Manual

Sending a Fax by Automatic Dialing
79
5. Sending 
Faxes
4Press .
5Enter a name by pressing number keys for each letter as shown in the 
chart below. Up to 15 characters can be entered. (If you do not wish to 
enter a name, go directly to Step 6.)
Example: SHARP = 7777  44  2  777  7
♦To enter two letters in succession that require the same key, press   
after entering the first letter. 
♦To enter a lower case letter, continue pressing the key for the letter until the 
lower case letter appears. To enter...

Sending a Fax by Automatic Dialing
80
Editing and clearing auto-dial numbers
If you need to make changes to a previously stored auto-dial number, or clear 
a number, follow these steps:
1Press   once and   once.
2Press   or   until the number you wish to edit or clear appears in 
the display.
3Press .
4Press   for EDIT or   for CLEAR.
•If you selected CLEAR, go to Step 8.
5If you selected EDIT, make the desired changes to the number. 
•Press   or   to move the cursor to the digit or digits you wish to...

Sending a Fax by Automatic Dialing
81
5. Sending 
Faxes
8Press .
9Return to Step 2 to edit or clear another number, or press   to 
return to the date and time display.
START/MEMORY
STOP
Using an auto-dial number
Once you have stored a fax or phone number, you can use it to send a fax or 
make a phone call.
1If you are sending a fax, load the 
document(s).
•If desired, press   to set the 
resolution and/or contrast.
2Press   (or  ) until the name of the other party appears in the 
display (if no name was...

Sending a Fax by Automatic Dialing
82
Sending a fax by Direct Keypad Dialing
You can also enter a full number with the number keys and then press the 
 key to begin dialing. You can use this method to dial a full number 
when you dont need to speak to the other party before faxing.
START/MEMORY
1Load the document(s).
•If desired, press   to set the 
resolution and/or contrast.
2Enter the number of the receiving machine by pressing the number 
keys.
•If a pause is required between any of the digits to...

Sending a Fax by Automatic Dialing
83
5. Sending 
Faxes
1If you are sending a fax, load the 
document(s).
•If desired, press   to set the 
resolution and/or contrast.
2Press   once.  appears in the display, followed by the last 
number dialed. Make sure the number that appears is the number you 
wish to dial.
3If you are sending a fax, press  . Dialing begins.
If you are making a phone call, lift the handset. Dialing begins.
RESOLUTION/
RECEPTION MODE
START/MEMORY
Redial
You can automatically redial the...

Sending a Fax by Automatic Dialing
84
Error Correction Mode
The fax machine is set to automatically correct any distortions in a 
transmission due to noise on the telephone line before printing at the 
receiving end. This function is called Error Correction Mode (ECM). ECM is 
effective for both transmissions and receptions, and is only effective when the 
other fax machine has ECM as well.
If desired, you can turn ECM off. This will increase slightly the amount of 
memory available for memory...

Sending a Fax From Memory
85
5. Sending 
Faxes
Sending a Fax From Memory
You can scan a document into the fax’s memory and send the document from 
memory. This increases transmission speed and allows you to send a fax to 
multiple destinations in a single operation. After transmission, the document is 
automatically cleared from memory.
Note: If a power failure occurs while sending a fax from memory, you will need 
to repeat the operation.
Broadcasting (sending a fax to multiple destinations)
This...

Sending a Fax From Memory
86
Memory transmission
You can also send a fax through memory when sending to a single 
destination. This is convenient when sending to destinations where the line is 
often busy, as it saves you from waiting to pick up the original document and 
frees the feeder for other operations.
6When you are ready to begin transmission, press  .
•A Transaction Report is automatically printed out after Broadcasting is 
completed. Check the Note column of the report to see if any of the...

87
6. Receiving 
Fa xe s
When the reception mode is set to FAX, the fax machine will automatically 
answer all calls on four rings and receive incoming faxes.
♦If you pick up the handset before the machine answers, you can talk to the 
other party and/or receive a fax as explained in Using TEL Mode on page 
88.
4 rings Fax reception
6.  Receiving Faxes
Using FAX Mode
RESOLUTION/
RECEPTION MODE
Changing the number of rings
If desired, you can change the number of rings on which the fax machine 
answers...

Using TEL Mode
88
2Press  once.
3Press  once.
4Enter the desired number of rings (any 
number from 2 to 5).
Example: 3 rings  
5Press   to return to the date and time display.
Note: If you are using Distinctive Ring, the fax machine will answer calls after two 
rings regardless of the above setting.
3
STOP
Using TEL Mode
The display briefly shows 
your selection, then:
To select TEL mode, press 
 until the arrow in 
the display points to TEL.
RESOLUTION/
RECEPTION MODE
When the reception mode is set to...