Sharp Ux Cl220 Plain Paper Fax And 2 4 Ghz Cordless Phone Wi Operation Manual

Messages and Signals
119
11. Trouble-
shooting
FAX RX IN MEMORY A fax has been received in memory because the 
imaging film needs replacement, you have run out of 
printing paper, or the paper is jammed. The fax will 
print out automatically when the problem is fixed.
FUNCTION MODE The FUNCTION key has been pressed.
INTERCOM The INTERCOM key has been pressed to page the 
cordless handset, or the cordless handset is paging 
the fax machine. Lift the handset to talk. When you 
are finished talking, replace...

Messages and Signals
120
NO DATA This appears if you attempt to search for an auto-dial 
number when none have been stored.
NO SERVICE This appears if you haven’t registered with OpenLCR 
and press the FUNCTION key and 7.
OFF HOOK This appears if you forgot to replace the handset after 
using it to dial and send a fax. Replace the handset or 
press the STOP key to clear the message.
ON HOOK DIAL The SPEAKER key has been pressed and the fax 
machine is waiting for you to dial.
OUT OF RANGE This will...

Messages and Signals
121
11. Trouble-
shooting
TOTAL MSGS:XX This indicates that you have received messages in 
the answering system. “XX” is the number of 
messages.
TOTAL PAGE(S) 01 Number of pages transmitted, received, or copied.
Display messages (cordless handset)
CHARGING The cordless handset is in the charger and the 
battery is charging.
FAX BUSY The fax machine is in use. Wait until the fax machine 
is no longer being used to use the cordless handset.
HOLD A call has been placed on hold by...

Messages and Signals
122
OUT OF RANGE The cordless handset is outside of the talking range 
of the fax machine. When talking on the cordless 
handset, the handset will beep and you may hear 
interference. Move closer to the fax machine.
REMOTE MODE The REMOTE/FLASH key has been pressed. For 
information on using REMOTE MODE, see page 71.
STAND-BY This appears when the cordless handset is not in the 
charger and is ready to be used.
TA L K T h e  TA L K key has been pressed to make a phone 
call.
Audible...

Clearing Paper Jams
123
11. Trouble-
shooting
Clearing Paper Jams
Clearing a jammed document
If the original document doesn’t feed properly during transmission or copying, 
or DOCUMENT JAMMED appears in the display, first try pressing  . If 
the document doesnt feed out, remove it as explained below.
Important:
Do not try to remove a jammed document without releasing it as explained 
below. This may damage the feeder mechanism.
START/MEMORY
1Press 
 and slowly open the operation 
panel until it is half...

Clearing Paper Jams
124
1Open the operation panel (press 
).
2Gently pull the jammed paper out of 
the machine, making sure no torn 
pieces of paper remain in the print 
compartment or rollers.
3Rotate the front gear until the film is taut, and then close the operation 
panel (press down on both sides to make sure it clicks into place).
Clearing jammed printing paper
4Flip down the green levers on each side of the white roller. Rotate the 
front gear until the film is taut, and then close the operation...

Ordering Parts
125
Ordering Parts
To order parts, contact the parts distribution center located nearest 
you. When ordering a part, use the part order number shown below. 
Operation manual  TINSE4267XHTZ
Setup Guide TCADZ3323XHZZ
Handset cord QCNWG209BXHBW
Telephone line cord QCNWG208BXHZZ
Handset DUNTK468BXHBW
Paper tray CPLTP3183XHR7
Paper tray extension  LPLTP3184XHZZ
Gears CGERH2566XH01
NGERH2568XHZZ
AC adapter RADPA2027XHZZ
Cordless handset charger RUNTZ2100XHE1
Part distribution centers...

FCC Regulatory Information
126
FCC Regulatory Information
This equipment complies with FCC rules, Part 68. On this equipment is a label 
that contains, among other information, the Registration Number and Ringer 
Equivalence Number (REN) for this equipment. If requested, this information 
must be provided to your telephone company. 
An FCC compliant telephone cord and modular plug is provided with this 
equipment. This equipment is designed to be connected to the telephone 
network or premises wiring...

127
SHARPDate Revised: .Date Issued :July. 3. 2001
MATERIAL SAFETY DATA SHEET (1/2)MSDS No. B-1026
Section 1. Product and Company Identification
Product Name :IMAGING FILM UX-5CR
Supplier Identification :Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Manufacturer :DAINIPPON PRINTING CO. LTD.
591-2, Kamihirose, Higashikubo, Sayamashi, Saitama, 350-1321 JAPAN
Emergency telephone number :+81-42-952-9666
Local suppliers are listed below. Please contact the nearest supplier for additional...

128
SHARP
Date Revised: .Date Issued :July. 3. 2001
MATERIAL SAFETY DATA SHEET (2/2)MSDS No. B-1026
Section 6. Accidental Release Measures
Rumpling the product may cause the wax layer to peel off. Sweep up or vacuum. When sweeping, avoid
raising film or dust. If a vacuum is used , motor should be rated as dust tight. Wash any residue off skin with
soap and water. Garments may be wasted or dry cleaned after removal of loose film or dust.
Section 7. Handling and Storage
No special precautions for safety...