Sharp Ar153e N Manual
Have a look at the manual Sharp Ar153e N Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![](/img/blank.gif)
19 3 SELECTING THE TRAY Press the tray select ( ) key. Each time you press the tray select ( ) key, the location indicated by the paper feed location indicator changes in the following order: paper tray 1, paper tray 2, multi- bypass tray. Paper sizes that can be used in the duplex copy mode are letter, legal, and invoice. When copying from the original table in the duplex copy mode, only letter size paper can be used. (AR-157E) The multi-bypass tray cannot be used in the duplex copy mode.
![](/img/blank.gif)
20 This chapter describes the special functions of this unit. Use these functions as needed. ABOUT THE SPECIAL FUNCTIONS OF AR-157E Two sided copying When copying from the RSPF, two-side originals can be copied automatically without having to manually turn them over. Automatic two-sided copying can also be performed without using the RSPF. When copying from one-sided originals to two- sided copies, copying orientation can be selected between Turn on Long Edge and Turn on Short Edge. When making two-sided copies from the original table, the paper size must be letter. When making two-sided copies from the RSPF, letter, legal, and invoice sizes can be used. Non-standard size paper cannot be used. When making two-sided copies, the multi-bypass tray cannot be used. When using two-sided invoice size originals from the RSPF, be sure to place them in the landscape orientation. Otherwise, an original misfeed will occur. A A A A A A A A Turn on Short Edge Turn on Long Edge 4SPECIAL FUNCTIONS
![](/img/blank.gif)
21 4 Making two-sided copies 1Place the original(s) on the original table or in the RSPF. (see ORIGINAL PLACEMENT (p.14). 2Select two-sided copy mode. A: When copying in a one-sided to two-sided mode: Use the original to copy key to select the desired one-sided to two-sided copying mode (Turn on Long Edge or Turn on Short Edge). See the illustrations on page 20. B: When copying in the two-sided to two-sided mode: Use the original to copy key to select the two-sided to two-sided copying mode. The originals must be set in the RSPF before this mode can be set in step 3 on page 15. C: When copying in the two-sided to one-sided mode: Use the original to copy key to select the two-sided to one-sided copying mode. The originals must have been set in the RSPF in step 3 on page 15. 3Select the copy settings. See SET THE COPY QUANTITY (p.16), EXPOSURE ADJUSTMENT/PHOTO COPYING (p.16), and REDUCTION/ENLARGEMENT/ZOOM (p.18). Using the original table If you are using the original table, copying is only possible in one sided to two-sided mode (A above). 1Press the start ( ) key. The original is scanned into the units memory and the number of the copy quantity blinks in the display. 2Place the original that you wish to copy onto the rear side of the paper, and press the start ( ) key again. Copying begins. Using the RSPF Press the start ( ) key. Copying begins in the selected two-sided copy mode. ABC
![](/img/blank.gif)
22 DESCRIPTION OF SPECIAL FUNCTIONS Toner save mode (page 22) Reduces toner consumption by approximately 10%. Power save modes (page 23) The unit has two power save modes of operation: preheat mode and auto power shut-off mode. Preheat mode When the unit enters the preheat mode, the power save ( ) indicator will light up and other indicators will remain on or off as before. In this condition, the fuser in the unit is maintained at a lower heat level, thereby saving power. To copy from the preheat mode, make desired copier selections and press the start ( ) key using the normal copying procedure. Auto power shut-off mode When the unit enters the auto power shut-off mode, the power save ( ) indicator will light up and other indicators except the ONLINE indicator will go out. The auto power shut-off mode saves more power than the preheat mode but requires a longer time before starting copying. To copy from the auto power shut-off mode, press the start ( ) key. Then make desired copier selections and press the start ( ) key using the normal copying procedure. Auto clear (page 23) The unit returns to the initial settings a preset amount of time after the end of copy, or scanner job. This preset amount of time (auto clear time) can be changed. Stream feeding mode (page 23) For description of the stream feeding mode, see Stream feeding mode (p.15). Resolution of AUTO & MANUAL mode (page 23) You can set the copy resolution used for AUTO and MANUAL ( ) exposure mode. TONER SAVE MODE 1Press the exposure mode selector key to select the MANUAL ( ) mode.
![](/img/blank.gif)
23 4 2Press and hold down the exposure mode selector key for approximately 5 seconds. The MANUAL ( ) indicator will go out and the PHOTO ( ) indicator will begin to blink. The light and dark indicator marked 5 will light up, indicating the standard toner mode is active. 3To enter the toner save mode, press the light ( ) key. The light and dark indicator marked 1 will light up, indicating the toner save mode is selected. 4Press the exposure mode selector key. The PHOTO ( ) indicator will stop blinking and light up steadily. The light and dark indicator marked 3 will light up. The toner save mode is now active. USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired. Setting the power save modes, auto clear time, stream feeding mode and resolution of AUTO & MANUAL mode 1Press and hold down the light ( ) and dark ( ) keys simultaneously for more than 5 seconds until all the alarm indicators ( , , , ) blink and appears in the display. 2Use the left copy quantity ( ) key to select a user program number (1: auto clear time, 2: preheat mode, 3: auto power shut-off timer, 4: stream feeding mode, 5: auto power shut-off mode 6: resolution of AUTO & MANUAL mode). The selected number will blink in the left side of the display. 3Press the start ( ) key. The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the display. 4Select the desired parameter using the right copy quantity ( ) key. The entered parameter number will blink on the right of the display. To return to the standard mode, repeat the procedure but use the dark ( ) key to select exposure level 5 in step 3.
![](/img/blank.gif)
24 * Factory default settings are indicated with an asterisk (*). 5Press the start ( ) key. The right-hand number in the display will be steadily lit and the entered value will be stored. 6Press the light ( ) or dark ( ) key to return to the normal copy mode. DISPLAYING TOTAL NUMBER OF COPIES Use the following procedure to display the total number of copies. 1Press the clear ( ) key to reset the display to zero. 2Press and hold down the clear ( ) key for approximately 5 seconds. The total number of copies will appear in two steps, each with three digits. Example: Total number of copies is 1,234. Program No.ModeParameters 1 Auto clear time0 OFF, 1 10sec., 2 30sec. *3 60sec., 4 90sec., 5 120sec. 2 Preheat mode *0 30sec., 1 60sec., 2 90sec. 3Auto power shut- off timer0 2min., *1 5min., 2 15min., 3 30min., 4 60 min., 5 120min. 4Stream feeding mode0 OFF, *1 ON 5Auto power shut- off mode0 OFF, *1 ON 6Resolution of AUTO & MANUAL mode*0 300dpi, 1 600dpi Program No. 4 can be used when your unit has the RSPF/SPF. To change the setting or to set another mode, press the clear ( ) key. The unit will return to step 2.
![](/img/blank.gif)
25 5 This chapter describes how to replace the toner cartridge and how to clean the unit. TONER CARTRIDGE REPLACEMENT When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner cartridge replacement required ( ) indicator blinks, the toner cartridge must be replaced before copying can be resumed. Replace the toner cartridge by following the procedure below. 1Open the multi-bypass tray, and then open the side cover while pressing the side cover open button. 2Push gently on both sides of the front cover to open the cover. Be sure to use only genuine SHARP parts and supplies. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package. During long copy run of a dark original, the start ( ) indicator may blink, the indicator light up, and the unit stop, even though toner is left. The unit will feed toner up to 2 minutes and then the start ( ) indicator will light up. Press the start ( ) key to restart copying. 5MAINTENANCE
![](/img/blank.gif)
26 3Gently pull the toner cartridge out while pressing the lock release lever. 4Remove the toner cartridge from the bag. Grasp the cartridge on both sides and shake it horizontally four or five times. After shaking the cartridge, remove the toner seal. 5Gently insert the toner cartridge along the guides until it locks in place while pushing the lock release lever. Remove the tape from the shutter. Pull the shutter out of the toner cartridge as shown in the illustration. Discard the shutter. • After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner to leak from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new cartridge. Dispose of the old toner cartridge in accordance with local regulations. Grasp the toner cartridge as shown in the illustration. Do not hold the cartridge by the shutter. Be sure to only shake the cartridge before the toner seal is removed. Toner cartridge lock release lever 4 or 5 times Shutter Toner seal
![](/img/blank.gif)
27 5 6Close the front cover and then the side cover by pressing the round projections near the side cover open button. The indicator will go out and the start ( ) indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. Even after a new toner cartridge is installed, the start ( ) indicator may not light up, indicating copying cannot be restarted (toner is not sufficiently fed). In this case, open and close the side cover. The copier will feed toner again approximately 2 minutes and then copying can be restarted.
![](/img/blank.gif)
28 CLEANING THE UNIT Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to regularly clean the unit. Cabinet Wipe the cabinet with a soft, clean cloth. Original table and the back side of the original cover/RSPF/ SPF Stains on the glass, RSPF/SPF scanning window, cover or RSPF/SPF roller will also be copied. Wipe the glass, RSPF/SPF scanning window, cover and RSPF/SPF roller with a soft, clean cloth. If necessary, dampen the cloth with a glass cleaner. Before cleaning, be sure to turn the power switch off and remove the power cord from the outlet. Do not use thinner, benzene or other volatile cleaning agents. Doing so may cause deformation, discoloration, deterioration or malfunction. Original table/scanning window Original cover/RSPF/SPF RSPF/SPF roller RSPF/SPF scanning window