Sharp Ar153e N Manual

19
3
SELECTING THE TRAY
Press the tray select ( ) key.
Each time you press the tray select ( ) key, the location 
indicated by the paper feed location indicator changes in 
the following order: paper tray 1, paper tray 2, multi-
bypass tray.
Paper sizes that can be used in the duplex copy mode are letter, legal, 
and invoice. When copying from the original table in the duplex copy 
mode, only letter size paper can be used. (AR-157E)
The multi-bypass tray cannot be used in the duplex copy mode. 

20
This chapter describes the special functions of this unit. Use these functions as 
needed.
ABOUT THE SPECIAL FUNCTIONS OF AR-157E
Two sided copying
When copying from the RSPF, two-side originals can be copied automatically 
without having to manually turn them over. Automatic two-sided copying can also be 
performed without using the RSPF. When copying from one-sided originals to two-
sided copies, copying orientation can be selected between Turn on Long Edge and 
Turn on Short Edge.
When making...

21
4
Making two-sided copies
1Place the original(s) on the original table or in the RSPF. (see 
ORIGINAL PLACEMENT (p.14).
2Select two-sided copy mode.
A: When copying in a one-sided to two-sided mode:
Use the original to copy key to select the desired one-sided to two-sided 
copying mode (Turn on Long Edge or Turn on Short Edge). See the 
illustrations on page 20.
B: When copying in the two-sided to two-sided mode:
Use the original to copy key to select the two-sided to two-sided copying 
mode. The...

22
DESCRIPTION OF SPECIAL FUNCTIONS
Toner save mode (page 22)
Reduces toner consumption by approximately 10%.
Power save modes (page 23)
The unit has two power save modes of operation: preheat mode and auto power 
shut-off mode.
Preheat mode
When the unit enters the preheat mode, the power save ( ) indicator will light up 
and other indicators will remain on or off as before. In this condition, the fuser in 
the unit is maintained at a lower heat level, thereby saving power. To copy from 
the preheat...

23
4
2Press and hold down the exposure mode 
selector key for approximately 5 seconds. 
The MANUAL ( ) indicator will go out 
and the PHOTO ( ) indicator will begin 
to blink. The light and dark indicator 
marked 5 will light up, indicating the 
standard toner mode is active.
3To enter the toner save mode, press the 
light ( ) key. The light and dark 
indicator marked 1 will light up, 
indicating the toner save mode is 
selected.
4Press the exposure mode selector key. The PHOTO ( ) 
indicator will stop...

24
* Factory default settings are indicated with an asterisk (*).
5Press the start ( ) key. The right-hand number in the display 
will be steadily lit and the entered value will be stored.
6Press the light ( ) or dark ( ) key to return to the normal 
copy mode.
DISPLAYING TOTAL NUMBER OF COPIES
Use the following procedure to display the total number of copies.
1Press the clear ( ) key to reset the display to zero.
2Press and hold down the clear ( ) key for approximately 5 
seconds. The total number of...

25
5
This chapter describes how to replace the toner cartridge and how to clean the unit.
TONER CARTRIDGE REPLACEMENT
When the toner cartridge replacement required ( ) indicator lights up, replacement 
of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner 
cartridge replacement required ( ) indicator blinks, the toner cartridge must be 
replaced before copying can be resumed. Replace the toner cartridge by following 
the procedure below.
1Open the multi-bypass tray, and 
then...

26
3Gently pull the toner cartridge 
out while pressing the lock 
release lever.
4Remove the toner cartridge from the bag. Grasp the cartridge 
on both sides and shake it horizontally four or five times. After 
shaking the cartridge, remove the toner seal.
5Gently insert the toner cartridge along 
the guides until it locks in place while 
pushing the lock release lever. 
Remove the tape from the shutter. Pull 
the shutter out of the toner cartridge 
as shown in the illustration. Discard 
the shutter.
•...

27
5
6Close the front cover and 
then the side cover by 
pressing the round 
projections near the side 
cover open button. The 
indicator will go out and the 
start ( ) indicator will light 
up.
When closing the covers, 
be sure to close the front 
cover securely and then 
close the side cover. If the 
covers are closed in the 
wrong order, the covers 
may be damaged.
Even after a new toner cartridge is installed, the start ( ) indicator 
may not light up, indicating copying cannot be restarted (toner is...

28
CLEANING THE UNIT
Proper care is essential in order to get clean, sharp copies. Be sure to take a few 
minutes to regularly clean the unit.
Cabinet
Wipe the cabinet with a soft, clean cloth.
Original table and the back side of the original cover/RSPF/
SPF
Stains on the glass, RSPF/SPF scanning window, cover or RSPF/SPF roller will also 
be copied. Wipe the glass, RSPF/SPF scanning window, cover and RSPF/SPF roller 
with a soft, clean cloth. If necessary, dampen the cloth with a glass cleaner.
 Before...