Sanyo Projector Plv Z1 User Manual

Multimedia Projector 
MODELPLV-Z1
PLV-Z1BL
Owner’s Manual 

2
Table of Contents
Table of Contents 2
Part Names and Functions 9Video Input 24
Computer Input/ (RGB Scart 21-Pin Video Input) 31
Setting 42
Appendix 44 To the Owner 3
Feature and Design 8
Front 9
Bottom 10
Back 10
Terminal 11
Top Controls and Indicators 12
Remote Control 13
Remote Control Batteries Installation 14
Operating Range 14Input Source Selection (Direct Operation) 24
Input Source Selection (Menu Operation) 25
Video System Selection (Video/S-Video) 26
Video System Selection (Y-Pb/Cb-Pr/Cr) 26...

3
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).  NO USER-
SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT.  REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNERS MANUAL WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this projector, read this...

4
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use.  Unplug this projector from AC power supply before
cleaning.  Do not use liquid or aerosol cleaners.  Use a damp
cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time,...

5
Safety Instructions
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
Do not drop or bump a projector, otherwise damages or malfunctions may result.
When carrying a projector, use a suitable carrying case.
Do not transport a projector by using a courier or transport service in an unsuitable transport case.  This may cause
damage to a projector.  To transport a projector through a courier or transport service, consult your dealer for best
way.
Moving the Projector
When moving the projector, close the...

6
Compliance
AC Power Cord for the United Kingdom :
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of
the plug.  Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating,
marked thus  .  If the fuse cover is detachable, never use the plug with the cover omitted.  If a replacement fuse
cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or...

7
NOTE ON THE POWER CORD
AC Power Cord must meet requirement of the country where you use a projector.
Confirm an AC plug type with the chart below and proper AC Power Cord must be used.
If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.
Compliance
To POWER CORD
CONNECTOR on your
projector.
Projector sideAC Outlet side
Ground
To the AC Outlet.
(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
This projector uses nominal input voltages of 100-120 V or 200-240
V...

8
Feature and Design
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use.  This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
Compatibility
This projector widely accepts various video and
computer input signals including;
Computers
IBM-compatible or Macintosh computer up to 1280
x 1024 resolution.
6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M...

9
Part Names and Functions
Front
PROJECTION LENS
FRONT COVER
INFRARED 
REMOTE RECEIVER
TOP CONTROLS
AND INDICATORS
AIR INTAKE VENTS 
EXHAUST VENTS
FOCUS RING
ZOOM LEVERLENS SHIFT RING
(LEFT/RIGHT)
LENS SHIFT RING
(UP/DOWN)
CAUTION
This projector is equipped with Cooling Fans for protection from overheating.  Pay attention to the following to ensure
proper ventilation and avoid a possible risk of fire and malfunction.
Do not cover vent holes.
Keep back and bottom clear of any object.  Obstructions may...

10
Part Names and Functions
Bottom
Back
CAUTION
Hot air is exhausted from the exhaust vents.  When using or installing the projector, the following
precautions should be taken.
Do not put any flammable objects near these vents.
Keep front grills at least 3’(1m) away from any objects, especially heat-sensitive objects.
Do not touch this area (including the top cabinet), especially screws and metallic parts.  This area will
become hot while the projector is used.
This projector detects internal...