Sanyo Projector Plc Xt16 User Manual

41
APPENDIX
CLEANING PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.
When the projector is not in use, replace Lens Cover.
1
3
Lightly wipe a cleaning cloth over Projection Lens.2
Follow these steps to clean Projection Lens:
MAINTENANCE
WARNING TEMP. INDICATOR
WARNING TEMP. Indicator flashes red and projector is automatically turned off when an...

42
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in the section
CONNECTING PROJECTOR  on pages 11 ~ 13.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still...

43
APPENDIX
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions,
contact the sales dealer where you purchased the
projector or the service center.Give the model number and explain the difficulty.  We will advise you how to obtain service.
Remote Control Unit
does not work.Check the batteries.
Check ALL-OFF switch on Remote Control Unit is set to “ON.”.
Make sure nothing is between...

44
APPENDIX
TECHNICAL SPECIFICATIONS
0.99 TFT Active Matrix type, 3 panels
Multi-media Projector
17.2 lbs (7.8 kg)
11.9 x 6.4 x 16.6 (302mm x 162mm x 422mm)
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 300”
800 TV lines
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Owner’s Manual
AC Power Cord
Remote Control Unit and Batteries...

45
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 and MONITOR OUT TERMINALS (ANALOG)
Terminal : HDB15-PIN 
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
+5V Power
Horiz. sync.
Ground (Vert.sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
13
10
12
11
14
15
Pin Configuration
1917
21018
31119
41220
51321
61422
71523
81624
C1
C2
C3
C5C4
Pin Configuration
Analog Red Input
Analog Ground (R/G/B)
Analog Green Input...

46
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those parts, give the name and Type No. to the sales dealer.
Control Cable (PS2 Port) Type No. : POA-MCPS2
Control Cable (ADB Port) Type No. : POA-MCMAC
MAC Adapter Type No. : POA-MACAP
HDB 15 pin-SCART 21 pin Cable Type No. : POA-CA-SCART
Media Card Imager Kit Type No. : POA-MD07MCI
Wireless Imager Kit Type No. :Available models are different in each country.  Contact the
sales dealer for details.
When using Wireless...

47
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.  
• • • on• • • dim• • • off• • • flashing
✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.  When this indicator lights yellow,
replace the projection lamp with a new one promptly.  Reset the Lamp Replace Counter after replacement of the lamp.  
The projector is OFF.  (The AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER ON-
OFF button.
The...

Printed in Japan
Part No. 610 308 2318 (1AA6P1P4100-- MH7A)
SANYO Electric Co., Ltd