Sanyo Projector Plc Wtc500l User Manual

21
Connecting to Video Equipment (Video, S-video, Component, HDMI and RGB Scart)
Cables used for connection  
• Video Cable (RCA x 1) • VGA-Scart Cable
• S-VIDEO Cable  • BNC Cable
• HDMI Cable 
(Cables are not supplied with the projector.)
VIDEO
S-VIDEO
S-video 
cable Composite 
Video 
Output
S-video 
Output
VIDEO
Unplug the power cords of both the projector and external 
equipment from the AC outlet before connecting cables.
✔Notes:
	 •	The	S-VIDEO	jack	connection	overrides	the	VIDEO	jack	
connection...

22
Connecting  for Audio Signal
Cables used for connection 
• Audio Cable (Mini Plug [stereo] x 2)
• Audio Cable (RCA x 2)
(Cables are not supplied with the projector.)
External Audio Equipment
Audio cable 
(stereo) Audio Input
Audio Output
AUDIO OUT 
(stereo)
Audio cable          
(RCA)AUDIO IN
Unplug the power cords of both the projector 
and external equipment from the AC outlet 
before connecting cables.
✔Notes:
	 •	When	the	AUDIO	OUT	is	plugged-in,	the	projector’s	built-
in	speaker	is	not...

23
NOTE ON THE POWER CORD
   AC power cord must meet the requirements of the country where you use the projector.
    Confirm the AC plug type with the chart below and proper AC power cord must be used.
    If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
To power cord 
connector on your 
projector.
Projector sideAC outlet side
Ground
To the AC outlet .
(120 V AC)
For Continental EuropeFor the U  .S .A .  and Canada
This projector uses nominal input voltages of...

24
Basic Operation
Connect the projector’s AC power cord into an AC 
outlet. The POWER indicator lights red.
Press the ON/STAND-BY button on the top control or 
the ON button on the remote control. The POWER 
indicator turns green and the cooling fans start to 
operate. The preparation display appears on the screen 
and the count down starts. 
2
3
1
16
The preparation display will disappear 
after 20 seconds.
4After the countdown, the input source that was 
selected the last time and the lamp control and...

25
Press the ON/STAND-BY button on the top control 
or the STAND-BY button on the remote control, and 
“Power off?” appears on the screen.
Press the ON/STAND-BY button or the STAND-BY 
button on the remote control again to turn off the 
projector. The POWER indicator starts to blink red after 
3 seconds.  After the projector is turned off, the cooling 
fans operates for 90 seconds. At this period of time you 
can unplug the AC power cord even if the fans are still 
running. During the POWER indicator is...

26
Top Control
Menu barPointer(red frame )
Menu icon
Item data
Press the Point 
7 8 
buttons to adjust the 
value.
SELECT 
button
Pointer (red frame )
Press the Point 
ed buttons 
to move the pointer.
Item
How to Operate the On-Screen Menu
MENU button
SELECT button
POINT buttons
On-Screen Menu
Quit
Exit this menu.
The projector can be adjusted or set via the On-Screen 
Menu. For each adjustment and setting procedure, refer to 
the respective sections in this manual.
Use the Point 
7 8 buttons to select a...

27
Menu Bar
System
Select a 
computer or 
video system 
mode (pp.36, 
37).
Image Adjust
Adjust the picture 
image (pp.42–44).
– Contrast
– Brightness
– 
– 
– Color temp.
– White balance
   (R/G/B)
– Sharpness
– Gamma
– 
– 
– Reset
– Store
– Quit
Setting Menu
Adjust the 
volume 
or mute 
the sound 
(p.29).
Image
Select an image 
level (p. 41).
– Dynamic
– Standard
– [Real]
– 
– Image 1–4
[PC Adjust]
Adjust 
parameters 
to match 
with an input 
signal format 
(pp.38–40)
Guide Window
Show the selected 
Menu...

28
The following lens operation can be made with the Lens 
button on the top control. 
Press the Lens button to enter each lens operation mode. 
The selected adjustment display appears on the screen.
Zoom ➜ Focus ➜Lens Shift ➜
• • • • •
Operating with Projector Control
Display “Lens shift” on the screen. Use the Point ed7 8 
buttons to position the screen to the desired point without 
having picture distortion. 
The screen can be moved up or down to 50 percent, or 
sideways up to 15 percent from...

29
1
2
Press the MENU button to display the On-Screen 
Menu. Use the Point 
7 8 buttons to move the red 
frame pointer to the Sound Menu icon.
Press the VOLUME+/– buttons on the top control or on the 
remote control to adjust the volume. The volume dialog box 
appears on the screen for a few seconds.
Press the MUTE button on the remote control to temporarily 
turn off the sound. To turn the sound back on, press the 
MUTE button again or press the VOLUME +/– buttons. The 
Mute function is also effective...

30
Remote Control
Operating with Remote Control
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons 
enables you to make the desired operation quickly without calling up the On-Screen Menu.
Press the FREEZE button on the remote control to freeze 
the picture on the screen. To cancel the Freeze function, 
press the FREEZE button again or press any other button.
FREEZE button
Press the AUTO PC button on the remote control to operate 
the Auto PC Adj....