Sanyo Projector Plc Wl2503 User Manual

							21
How to Operate the On-Screen Menu
The	projector	can	be	adjusted	or	set	via	the	On-Screen	
Menu.	The	menu	has	a	hierarchical	structure,	with	a	main	
menu	that	is	divided	into	submenus,	which	are	further	
divided	into	other	submenus.	For	each	adjustment	and	
setting	procedure,	refer	to	respective	sections	in	this	
manual.
Use	the	Point	▲▼	buttons	to	highlight	and	select	a	
main	menu	item.	Press	the	Point	►	or	the SELECT 	
button	to	access	the	submenu	items.	(The	selected	
item	is	highlighted	in	orange.)
Use	the	Point	▲▼	buttons	to	select	the	desired	
submenu	item	and	press	the	SELECT 	button	to	set	or	
access	the	selected	item.
Press	the	MENU	button	on	the	remote	control	or	on	the	
top	control	to	display	the	On-Screen	Menu.1
2
3
On-Screen Menu
POINT buttons
(arrowhead)
Top Control
Point
► or SELECT button
Use	the	Point	▲▼◄►	buttons	to	adjust	the	setting	or	
switch	between	each	option	and	press	the	SELECT 	
button	to	activate	it	and	return	to	the	submenu.
4
Press	the	Point	◄	button	to	return	to	the	main	menu.	
Press	the	MENU	button	to	exit	the	On-Screen	Menu.5
The	currently	set	item	is	marked.
The	selected	item	ishighlighted	in	orange.
Basic Operation
HDMI
ASPECTMENU button
POINT buttons
(arrowhead)
Remote Control
SELECT button
MENU button
SELECT button 
						

							22
Menu Bar
For	detailed	functions	of	each	menu,	see	“Menu	Tree”	on	pages	68-69.
①
②
③
④
⑤
⑥
⑦
⑧
Main	MenuSub-Menu
⑨
⑩
③ Image select
 For	computer	source,	used	to	select	an	image	mode	from	among	Dynamic,	Standard,	Real,	Blackboard(Green),	
Colorboard	and	Image 1-4.		(p.33)
						For	video	or	HDMI	source,	used	to	select	an	image	mode	among	Dynamic,	Standard,	Cinema,	Blackboard(Green),	
Colorboard	and	Image 1-4.		(p.40)
④ Image adjust
	 For	computer	source,	used	to	adjust	computer	image	[Contrast,	Brightness,	Color temp .,	White balance (Red/Green/
Blue), Sharpness	and	Gamma].		(pp.34-35)
						For	video	or	HDMI	source,	used	to	adjust	picture	image	[Contrast,	Brightness,	Color,	Tint,	Color temp .,	White 
balance (Red/Green/Blue),	Sharpness,	Gamma,	Noise reduction and	Progressive].		(pp.41-42)
② PC adjust
 Select	Auto PC adj .,	Fine sync,	Total dots,	Horizontal,	Vertical,	Current mode,	Clamp,	Display area H	and	Display 
area V	to	adjust	the	parameters	to	match	with	the	PC	input	signal	format.		(pp.34-35)
⑤ Screen
 For	computer	source,	used	to	adjust	size	of	the	image	[Normal,	True,	Full,	Custom	and	Digital zoom +/–	].		(pp.35-36)
						For	video	or	HDMI	source,	used	to	set	size		of	image	[Normal,	Full,	Zoom,	Wide, Natural wide	and	Custom].		(p.43)
① Input
	 Used	to	select	an	input	source	from	Computer 1,	Computer 2,	HDMI,	Video	or	S-video.  (pp.27-28,37-38)
⑥ Sound
 Used	to	adjust	the	volume	or	mute	the	sound.		(p.24)
⑧ Information
 Display	the	input	source	information:	Input	,	H-sync freq .,	V-sync freq .,	Screen,	Language,	Lamp status,	Lamp 
counter,	Power management,	Key lock,	PIN code lock	and	Remote control . 	(p.59)
⑩ Guide
 The	key	operation	is	displayed.
⑦ Setting
						Used	to	set	the	projector’s	operating	configurations.		(pp.44-58)
⑨ Network
 See	owner’s	manual	of	“Network	Set-up	and	Operation”.
Basic Operation 
						

							23
Focus Adjustment
Auto	setup	function	is	provided	to	automatically	execute	
the	setting	of	Auto	setup	(includes	Input	search	and	 Auto	
PC	adj.	functions)	in	the	Setting	Menu	by	just	pressing	the	
AUTO	SET	button	on	the	remote	control.	Refer	to	page	45	
for	the	setting	of	the	 Auto	setup	function.
Note:
   Fine sync,	Total dots,	Horizontal	and	Vertical	position	
of	some	computers	can	not	be	fully	adjusted	with	the	 Auto	
PC	adjustment	function.	When	the	image	is	not	provided	
properly	with	this	operation,	manual	adjustments	are	
required.		(pp.31-32)
Auto Setup Function
Basic Operation
Press	the	KEYSTONE	button	on	the	remote	control	or	on	
the	top	control.	The	Keystone	dialog	box	appears.	Use	
the	Point	▲▼	buttons	to	correct	keystone	distortion.	 The	
keystone	adjustment	can	be	stored	(see	page	46).
Reduce	the	upper	width	
with	the	Point	▲	button.	
Reduce	the	lower	width	
with	the	Point	▼	button.		
•	The	white	arrows	indicate	that	there	is	no	correction.
•	A	red	arrow	indicates	the	direction	of	correction.
•	An	arrow	disappears	at	the	maximum	correction.
•	If	you	press	the	KEYSTONE	button	on	the	remote	
control	or	on	the	top	control	once	more	while	the	
keystone	dialog	box	is	being	displayed,	the	keystone	
adjustment	will	be	canceled.
•	The	adjustable	range	is	limited	depending	on	the	
input	signal.	
Keystone Correction
Remote Control
HDMI
ASPECT
AUTO SET button
Adjust	the	lens	focus	with	the	focus	lever.Focus	Lever
Remote ControlHDMI
ASPECT
POINT ▲▼ buttons
KEySTONE button
Top Control
KEySTONE buttonPOINT ▲▼ buttons 
						

							24
Sound Adjustment
1
2
Press	the	MENU	button	to	display	the	On-Screen	Menu.	
Use	the	Point	▲▼	buttons	to	select	Sound.	Press	the	
Point	►	or	the	SELECT	button	to	access	the	submenu	
items.	
Press	the	VOLUME+/–	buttons	on	the	remote	control	or	on	
the	top	control	to	adjust	the	volume.	 The	volume	dialog	box	
appears	on	the	screen	for	a	few	seconds.
Press	the	MUTE	button	on	the	remote	control	to	select	On 
to	temporarily	turn	off	the	sound.	To	turn	the	sound	back	
on,	press	the	MUTE	button	again	to	select	Off	or	press	the	
VOLUME	+/–	buttons.	The	MUTE	function	is	also	effective	
for	the	AUDIO	OUT 	jack.
Press	the	SELECT 	button	to	switch	the	Mute	function	On/
Off.	When	the	sound	is	turned	off,	On	is	displayed.	Press	
the	VOLUME	+/–	buttons	again	to	turn	the	sound	back	on.
Use	the	Point	▲▼	buttons	to	select	the	desired	submenu	
item	and	press	the	SELECT 	button	to	access	the	
selected	item.
Volume
Press	the	Point	►	button	to	turn	up	the	volume;	press	the		
Point	◄	button	to	turn	down	the	volume.
Mute 
Direct Operation
Menu Operation
Sound Menu
Volume Dialog Box
HDMI
ASPECT
Remote Control
VOLUME + button
VOLUME - button
MUTE button
Approximate	level	
of	the	volume.
Press	the	MUTE	button	to	set	the	
Mute	function	On	or	Off.	The	dialog	
box	disappears	after	4	seconds.
Basic Operation
Volume
Mute 
Top Control
VOLUME +/- buttons 
						

							25
Remote Control Operation
Using	the	remote	control	for	some	frequently	used	operations	is	advisable.	Just	pressing	one	of	the	buttons	
enables	you	to	make	the	desired	operation	quickly	without	calling	up	the	On-Screen	Menu.
Press	the	COMPUTER	1/2,	HDMI,	VIDEO,	S-VIDEO	and	
COMPONENT	buttons	on	the	remote	control	to	select	the	
input	source.		See	pages	27-28,	37-38	for	details.
COMPUTER 1/2, HDMI, VIDEO, S-VIDEO and 
COMPONENT buttons
Display	the	input	source	information:	Input,	H-sync freq .,	
V-sync freq .,	Screen,	Language,	Lamp status,	Lamp 
counter,	Power management,	Key lock,	PIN code lock 
and	Remote control.		(p.59)
INFO . button
Press	the	D.ZOOM	buttons	on	the	remote	control	to	enter	to	
the	D.	zoom	+/–	mode.		See	page	36	for	details.
D .ZOOM buttons
Remote Control
HDMI
ASPECT
FREEZE button  
D .ZOOM buttons
LAMP  button
Note:
 		 See	the	next	page	for	the	description	of	other	
buttons.
LAMP button
COMPUTER 1/2buttons
VIDEO button
Press	the	LAMP 	button	 on	the	 remote	 control	to	select	 the	
lamp	mode	for	changing	the	brightness	on	the	screen.
INFO . button
S-VIDEO  button
COMPONENTbutton
Basic Operation
HDMI button
ASPECT button
Select	a	screen	aspect	from	4:3,	16:9 and 16:10.		(p.50)
ASPECT button
FREEZE button
Press	the	FREEZE	button	on	the	remote	control	to	freeze	
the	picture	on	the	screen.	 To	cancel	the	Freeze	function,	
press	the	FREEZE	button	again	or	press	any	other	button.
Fig.1	will	appear	on	the	Screen	menu	while	the	Freeze	
function	is	working.
Fig .1
Note:
			When	4:3	or	16:9 is	selected,	some	Screen	
modes	are	limited.	See	pages	35	and	43	for	
details.
Note:
	 When	use	the	MUTE	button	to	release	the	Freeze	function,	
	the	mute	function	can	not	be	operated	at	the	same	time.	
Normal	......	 Normal	brightness.	
Eco 	...........	Lower	brightness	reduces	the	lamp	power
																				consumption	and	extends	the	lamp	life. 
						

							26
Press	the	NO	SHOW	button	on	the	remote	control	to	black	
out	the	image.	To	restore	to	normal,	press	the	NO	SHOW	
button	again	or	press	any	other	button.	When	the	projected	
image	is	captured	and	is	set	as	User	in	the	Logo	selection	
(p.47),	the	screen	changes	each	time	you	press	the	NO	
SHOW	button	as	follows.
black	out	→	the	captured	image	→	normal	→	•	•	•	•	•
NO SHOW button
Press	the	P-TIMER	button	on	the	remote	control	to	operate	
the	Count	up/Count	down	function.	Refer	to	p.52	for	detail	of	
Setting	for	the	P-timer	function.
To	stop	the	count	time,	press	the	P-TIMER	button.
To	cancel	the	P-timer	function,	press	and	hold	the	P-TIMER	
button	for	a	few	seconds.
P-TIMER button
Press	the	IMAGE	button	on	the	remote	control	to	select	a	
desired	image	mode	of	the	screen.	See	pages	33,	40	for	
details.
IMAGE button
No show	disappears	after	4	seconds.
Note:
 		See	the	previous	page	for	the	description	of	
other	buttons.
HDMI
ASPECT
IMAGE button
NO SHOW button 
P-TIMER button
SCREEN button
Select	the	screen	size	(See	pages	35-36,	43	for	details).
SCREEN button
Basic Operation
Remote Control
Note:
	 When	use	the	MUTE	button	to	release	the	No	Show	function,	
		the	mute	function	can	not	be	operated	at	the	same	time.	 
						

							27
HDMI
ASPECT
Choose	Computer 1(RGB)	by	pressing	the	COMPUTER	1	
button	on	the	remote	control	or	press	the	INPUT	button	on	
the	top	control.	
Before	using	these	buttons,	correct	input	source	should	be	
selected	through	Menu	operation	as	described	below.
1
Input Menu
2
3
Input Source Selection (Computer 1: RGB)
Computer Input 
COMPUTER 1 button
Note:
	 	 When	the	Input	Search	function	is	set	to	On 1	or	On 2	in	
the	Auto	setup	function,	the	input	signal	will	be	searched	
automatically	(p.45).
Computer 1
Remote Control
Press	the	MENU	button	to	display	the	On-Screen	
Menu.	Use	the	Point	▲▼	buttons	to	select	Input	and	
then	press	the	Point	►	or	the	SELECT 	button.	
Use	the	Point	▲▼	buttons	to	select	Computer 1.	
When	Computer 1	is	selected,	press	the	Point	►	to	
access	the	submenu	items.	Use	the	Point	▲▼	buttons	
to	select	the	RGB	input	source	and	then	press	the	
SELECT	button.
Computer 1(RGB)
Computer 1(Scart)
Direct Operation
Menu Operation
INPUT button
Top Control
*COMPUTER	2	can	not	be	selected	when	using	the	
COMPUTER	IN	2/	MONITOR	OUT 	terminal	as	MONITOR	
OUT	output.
Computer 1 
Computer 2 *
HDMI
Video
S-video 
						

							28
Choose	Computer 2 (RGB)	by	press	the	COMPUTER	2	
button	on	the	remote	control	or	press	the	INPUT	button	on	
the	top	control.	
Before	using	these	buttons,	correct	input	source	should	be	
selected	through	Menu	operation	as	described	below.
Note:
	 	 When	the	Input	Search	function	is	set	to	On 1	or	On 2	in	
the	Auto	setup	function,	the	input	signal	will	be	searched	
automatically	(p.45).
HDMI
ASPECT
COMPUTER 2 button
Remote Control
1
2
Press	the	MENU	button	to	display	the	On-Screen	
Menu.	Press	the	Point	▲▼	buttons,	move	the	highlight	
to	Input	and	then	press	the	Point	►	or	the	SELECT 	
button.	
Use	the	Point	▲▼	buttons	to	select	Computer 2	and	
then	press	the	SELECT 	button.
Input Menu
Computer 2 (RGB)*
3When	Computer 2 is	selected,	analog	RGB	input	
source	will	be	selected	directly.
Computer Input
Input Source Selection (Computer 2: RGB)
Direct Operation
Menu Operation
INPUT button
Top Control
*COMPUTER	2	can	not	be	selected	when	using	
the	COMPUTER	IN	2/	MONITOR	OUT 	terminal	
as	MONITOR	OUT	output.
Computer 1 
Computer 2 *
HDMI
Video
S-video 
						

							29
PC System Menu
PC System Menu
Computer System Selection
This	projector	automatically	tunes	to	various	types	of	computers	with	its	Multi-scan	system	and	Auto	PC	
adjustment.	If	a	computer	is	selected	as	a	signal	source,	this	projector	automatically	detects	the	signal	format	
and	tunes	to	project	a	proper	image	without	any	additional	settings.	(Signal	formats	provided	in	this	projector	are	
shown	on	pages	71-72.)
One	of	the	following	messages	may	appear	when:
When	the	projector	can	not	recognize	the	
connected	signal	conforming	to	the	provided	
PC	Systems,	Auto	is	displayed	on	the	System	
Menu	box	and	the	Auto	PC	adjustment	function	
works	to	display	proper	images.	If	the	image	is	
not	projected	properly,	a	manual	adjustment	is	
required.			(pp.31-32)
There	is	no	signal	input	from	the	computer.	
Check	the	connection	between	your	computer	
and	the	projector.		(See	“Troubleshooting”	on	
page	66.)
Auto
-----
The	preset	system	is	manually	adjusted	in	the	
PC	adjust	Menu.	The	adjusted	data	can	be	
stored	in	Mode 1-10.		(pp.31-32)
Mode 1
PC	Systems	provided	in	this	projector	is	chosen.		
The	projector	chooses	a	proper	system	provided	
in	the	projector	and	displays	it.		
SVGA 1
* Mode 1	and	SVGA 1	are	examples.		
1
2
PC	system	can	also	be	selected	manually.
Press	the	MENU	button	to	display	the	On-Screen	
Menu.	Use	the	Point	▲▼	buttons	to	select	Input	and	
then	press	the	Point	►	or	the	SELECT	button.
Use	the	Point	▲▼	buttons	to	select	System	and	then	
press	the	Point	► or	the	SELECT	button.
Use	the	Point	▲▼	buttons	to	select	the	desired	system	
and	then	press	the	SELECT 	button.3
Selected	system	in	the	PC	
System	Menu	is	displayed.
Systems	in	this	dialog	box	
can	be	selected.
Customized	Mode (1–10) 
set	in	the	PC	adjust	Menu	
(pp.31-32).
Computer Input
Selecting Computer System Manually 
						

							30
Auto	PC	adjustment	function	is	provided	to	automatically	adjust	Fine sync,	Total dots,	Horizontal	,	Vertical 
and	Clamp	position	to	conform	to	your	computer.
PC adjust Menu
Auto PC adjustment
To store adjustment parameters
The	adjusted	parameters	from	the	Auto	PC	adjustment	can	
be	stored	in	the	projector.	Once	the	parameters	are	stored,	
the	setting	can	be	done	just	by	selecting	a	Mode (1-10)	in	
the	PC	System	Menu	(see	page	29).	See	also	“Store”	on	
page	32.
Note:
	 •	Fine sync,	Total dots,	Horizontal	and	Vertical 
position	of	some	computers	can	not	be	fully	adjusted	
with	the	Auto	PC	adjustment	function.	When	the	image	
is	not	provided	properly	with	this	operation,	manual	
adjustments	are	required	(pp.31-32).
	 •	The	Auto	PC	adjustment	can	not	be	operated	when	
480i,	575i,	480p,	575p,	720p,	1035i	or	1080i	is	selected	
in	the	PC	System	Menu	(p.29)	,	or	when	the	signal	is	
coming	from	the	HDMI	terminal.	
Press	the	MENU	button	to	display	the	On-Screen	
Menu.	Use	the	Point	▲▼	buttons	to	select	PC adjust 
and	then	press	the	Point	►	or	the	SELECT	button.
1
2Use	the	Point	▲▼	buttons	to	select	Auto PC adj .	and	
then	press	the	SELECT 	button.
Auto PC adj .
Use	Point	▲▼	buttons	to	select	Auto PC 
adj . and	press	the	SELECT	button.
Please wait . . .	appears	while	the	Auto	PC	
adjustment	is	in	process.
Computer Input
Menu Operation