Sanyo Plc Xu41 Projector User Manual

11
Part Names and Functions
Part Names and Functions
P-
TIMER
FREEZE
COMPUTERVIDEO
PAGESELECT
D.ZOOM
MUTE
VOLUME-MENU
NO SHOW
IMAGE
VOLUME+
KEYSTONE
AUTO PC
ON-
OFF
To ensure safe operation, please observe the following
precautions :
–  Do not bend, drop the remote control or expose
Remote Control to moisture or heat.
–  For cleaning, use soft dry cloth.   Do not apply
benzene, thinner, splay or any chemical material.
y
30° 30°
Point the remote control toward the projector
(Infrared Remote Receiver) when...

12
Part Names and Functions
Remote Control Battery Installation
To ensure safe operation, please observe the following precautions :
–Use (2) AAA, SUM-4 or R03 type alkaline batteries.
–Replace two batteries at the same time.
–Do not use a new battery with a used battery.
–Avoid contact with water or liquid.
–Do not expose the remote control to moisture, or heat.
–Do not drop the remote control.
–If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
–Risk of...

13
Installation
Projection angle can be adjusted up to 11.8 degrees with the
adjustable feet. 
Lift the front of the projector and pull upward the feet lock
latches on both sides of the projector.1
Adjustable Feet
Feet Lock Latches
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to adjust the position and tilt. 2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can...

14
NOTE ON THE POWER CORD
AC power cord must meet requirement of the country where you use a projector.
Confirm an AC plug type with the chart below and proper AC power cord must be used.
If supplied AC power cord does not match your AC outlet, contact your sales dealer.
Installation
To power cord
connector on your
projector.
Projector sideAC outlet side
Ground
To the AC outlet.
(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
This projector uses nominal input voltages of 100-120 V or 200-240
V...

15
Installation
Installation
Connecting to a Computer
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)
ARIALE)
AUD
COMPUTER  IN  1
MONITOR  OUT
S-VIDEO
 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)/ COMPONENT  IN  
COMPUTER  IN  2
/   
AUDIO  OUT
(VARIABLE)
Cables used for connection
• VGA Cable (HDB 15 pin) (Only a cable is supplied.)
• USB Cable✽
• Audio Cables...

16
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)
(VARIABLE)
AUDIO  OUT
COMPUTER  IN  1
MONITOR  OUT
S-VIDEO
 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)/ COMPONENT  IN  
COMPUTER  IN  2
/   
AUDIO  OUT
(VARIABLE)
Installation
Connecting to Video Equipment
Cables used for connection
• Video and Audio Cable (RCA x 3) ✽
• S-VIDEO Cable ✽
• Audio Cables (Mini Plug:...

17
Installation
Installation
Connecting to Component Video Equipment
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)
(VARIABLE)
AUDIO  OUT
MONITOR  OUT
S-VIDEO
 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
(MONO)COMPUTER  IN  1/ COMPONENT  IN  
COMPUTER  IN  2
/   
AUDIO  OUT
(VARIABLE)
Cables used for connection
• Audio Cables (Mini Plug (stereo) x 2 or RCA x 2) ✽
•...

18
Connect the projectors AC power cord into an AC outlet.
The POWER indicator blinks red in a moment and lights red.
Press the POWER ON-OFF button on the top control or on
the remote control.  The POWER indicator turns green
lighting and the cooling fans start to operate.  The
preparation display appears on the screen and the count
down starts. 
2
3
1
16
The preparation display disappears after 20 seconds.
4After the count-down, the input source that was selected
last and the Lamp mode status icon (see...

19
Basic Operation
Basic Operation
Press the POWER ON-OFF button on the top control or on
the remote control, and a message Power off? appears on
the screen.  
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to blink red, and it
continues while the cooling fans are operating for about 90
seconds. (About 120 seconds when the fan mode is L2. See
page 44.)   
1
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT...

P-
TIMER
FREEZE
COMPUTERVIDEO
PAGESELECTD.ZOOM
MUTE
VOLUME-MENU
NO SHOW
IMAGE
VOLUME+
KEYSTONE
AUTO PC
ON-
OFF
20
Basic Operation
ON - OFFPOWER
KEYSTONEINPUT
WARNING
LAMP
REPLACE
MENU
VOLUME–VOLUME+SELECT
Top Control
Menu bar Pointer
(red frame)Menu icon
Item data
Press the Point 
7 8buttons
to adjust value.
SELECT
button
Pointer (red frame)
Press the Point d button to
move the pointer.
Item
SELECT button POINT buttons
Remote Control
How to Operate the On-Screen Menu
MENU button SELECT button POINT...