Sanyo Plc Xk2200 Projector User Manual

61

Maintenance and Cleaning
When	the	projection	lamp	of	the	projector	reaches	its	end	of	life,	the	Lamp	replacement	icon	appears	on	the	screen	and	LAMP	REPLACE	indicator	lights	yellow.	Replace	the	lamp	with	a	new	one	promptly.	 The	timing	when	the	LAMP	REPLACE	indicator	should	light	is	depending	on	the	lamp	mode.
Follow	these	steps	to	replace	the	lamp.
For	continued	safety,	replace	with	a	lamp	of	the	same	type.	Do	not	drop	a	lamp	or	touch	a	glass	bulb!	The	glass	can	shatter	and	may	cause	injury.
Allow...

6

Maintenance and Cleaning
This	projector 	uses 	a 	high-pressure 	lamp 	which 	must 	be 	handled 	carefully 	and	properly.		Improper	handling	may	result	in	accidents,	injury,	or	create	a	fire	hazard.
● Lamp life may differ from lamp to lamp and according to the environment of use.	Lamp 	life 	may 	differ 	from 	lamp 	to 	lamp 	and 	according 	to 	the 	environment 	of 	use.	There 	is 	no 	guarantee 	of 	the 	same 	life 	for 	each 	lamp. 	Some 	lamps 	may 	fail 	or	terminate	their	life	in	a	shorter...

63

Appendix	
	 Problem:	–	Solutions
 No power	 –	Plug	the	power	cord	of	the	projector	into	the	 AC	outlet.		 	–	See	if	the	POWER	indicator	lights	red.		 	–		
Wait	until	the	POWER	indicator	stops	blinking	to	turn	on	the	projector	again.	 The	projector	can	be	turned	on	after	the	POWER	indicator	turns	red.	See	page	18.	 	 –	Check	the	WARNING	indicator.	If	the	WARNING	indicator	lights			 		 red,	projector	cannot	be	turned	on.	See	page	58.		 	–	Check	the	projection	lamp.	See	page	61.		 	–	Unlock	the	Key...

64

Appendix
 No image	 –	Check	the	connection	between	your	computer	or	video						 		 	 			equipment	and	the	projector.	See	pages	14-16.		 	–	See	if	the	input	signal	is	correctly	output	from	your	computer.			 		 				Some	laptop	computers	may	need	to	change	the	setting	for			 																																																												monitor	output	when	connecting	to	a	projector.	See	your			 		 	 			computer’s	instruction	manual	for	the	setting.			 	–	It	takes	about	30	seconds	to	display	an	image	after...

65

Appendix
	 The	image	is	distorted	or	runs	off.	–	Check	PC adjust	menu	or	Screen	menu	and	adjust	them.		 		 				See	pages	30-31,	34-35.
	 PIN	code	dialog	box	appears	 –	PIN	code	lock	is	being	set.	Enter	a	PIN	code	(the	“134”	or	numbers				at start-up .	 	 you	have	set).	See	pages	19,	53-54.
	 The	Remote	Control	does	–	Check	the	batteries.		not work .	 –	Make	sure	no	obstruction	is	between	the	projector	and	remote		 	 	 control.		 	–	Make	sure	you	are	not	too	far	from	the	projector	when	using	the...

66

WARNING	:High	voltages	are	used	to	operate	this	projector.	Do	not	attempt	to	open	the	cabinet.
If	problems	still	persist	after	following	all	operating	instructions,	contact	the	dealer	where	you	purchased	the	projector	or	the	service	center.	Specify	the	model	number	and	explain	about	the	problem.	We	will	advise	you	how	to	obtain	service.
This	symbol	on	the	nameplate	means	the	product	is	Listed	by	Underwriters	Laboratories	Inc.		It	is	designed	and	manufactured	to	meet	 rigid	U.L.	safety	standards...

67

Appendix
Menu	Tree
Computer	Input/Video	Input
VolumeMuteOn/OffSound0-63
RGB	Component
S-videoRGB
RGB	(Scart)
Input
Video
Computer	1
Computer	
MICOn/OffMIC	gain0-63Standby	MIC	outOn/Off
Dynamic
CinemaBlackboard	(Green)
Image	1
Image	selectStandard
ColorboardRed/Blue/Yellow/Green
Image	4
Real
LanguageSetting0	languages	provided.
Blue/User/BlackOff	/On/Countdown	offLogo	select
On/OffOn/Off
Ready
On/Off
Code	1–Code	
Keystone
BackgroundDisplayLogo
CeilingRear
Power	management
Direct	on...

68

AutoPALSECAMNTSCNTSC	4.43PAL-MPAL-N
Video	Input
Auto1080i1035i70p575p480p575i480i
0–630–63
Off
System	()
System	(3)
Image	AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15	0–15
Image	1
Screen
Yes/No
OffNoise	reductionL1L
0–630–63
Image	4
LL1
Film
Color	temp.
Scale
Reset
H/V
H/VYes/NoYes/No
Custom	adj.On/OffH&V
MidLowXLow
UserHigh
PositionCommon
IrisOff/On
SVGA	1Mode	1Mode		-	-	-	-
Total	dotsHorizontalVertical
Display	area...

69

Check	the	indicators	for	projector	condition.																																			
•	•	•	green.•	•	•	red•	•	•	off
•	•	•	blinks	green.
	When	the	projection	lamp	reaches	its	end	of	life,	the	LAMP	REPLACE	indicator	lights	yellow.					When	this	indicator	lights	yellow,	replace	the	projection	lamp	with	a	new	one	promptly.	(pp.	55,	61)
The	projector	is	off.	(The	AC	power	cord	is	unplugged.)
The	projector	is	in	stand-by	mode.	Press	the	ON/STAND-BY 	button	to	turn	on	the	projector.
Projector ConditionPOWER...

70

Compatible	Computer	Specifications
Basically	this	projector	can	accept	the	signal	from	all	computers	with	the	V-,	H-Frequency	mentioned	below	and	less	than	140	MHz	of	Dot	Clock.		When	selecting	these	modes,	PC	adjustment	can	be	limited.
ON-SCREEN	DISPLAYRESOLUTIONH-Freq.(KHz)V-Freq.(Hz)VGA	1640	x	48031.4759.88VGA	70	x	40031.4770.09VGA	3640	x	40031.4770.09VGA	4640	x	48037.8674.38VGA	5640	x	48037.867.81VGA	6640	x	48037.5075.00
MAC	LC13640	x	48034.9766.60MAC	13640	x	48035.0066.67
MAC...