Sanyo Plc Xf47 Projector User Manual

71

When an input signal is digital from the DVI terminal, refer to the chart below.
Appendix
✔Note:
	 •	Depending	on	the	condition	of	signals	and	the	type	and	length	of	cables,	these	signals	may	not	be	properly	
viewed.
	 •	Specifications	are	subject	to	change	without	notice.
ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
D-VGA640x48031.470 59.940 
D-480p720x48031.470 59.880 
D-575p720x57531.250 50.000 
D-SVGA800x60037.879 60.320 
D-XGA1024x76843.363 60.000 
D-WXGA 11366x76848.360 60.000...

7

Technical Specifications
Mechanical Information 
 Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  22.87” x 9.902” x 32.11” (581 mm x 251.5 mm x 815.5 mm) (Not including adjustable feet)
 
  Net Weight  80.3 lbs (36.5 kg)
 
  Feet Adjustment  0˚ to 5.7˚           
              
Panel Resolution 
 LCD Panel System  1.8” TFT Active Matrix type, 3 panels  
  Panel Resolution  1,024 x 768 dots
 
  Number of Pixels  2,359,296 (1,024 x 768 x 3 panels)           
            
Signal...

7

Optional Parts
     Model No.
Wired Remote Cable(30m)    
: POA-CA-RC30 
Option Slot Board (DVI)    
: POA-MD18DVI
Option Slot Board (5-BNC)    
: POA-MD16DVI
Option Slot Board (D-sub 15)    
: POA-MD04VGA
Option Slot Board (Dual-SDI)    
: POA-MD17SDID
Option Slot Board (Network board)   
: POA-MD13NET2
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. 
to the sales dealer.
Appendix
●  The specifications are subject to change without...

74

Configurations of Terminals
ANALOG (Mini D-sub 15 pin)
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5

4

6
7

+5V Power
Horiz. sync.
Ground (Vert. sync.)
DDC Data
Sense 0
Vert. sync.
DDC Clock
9
1
10
1
11
14
15
CONTROL PORT CONNECTOR (D-sub 9 pin)
-----
R X D
T X D
-----
SG
-----
RTS
CTS
Serial
1


4
5
6
7

DIGITAL DVI-D (DVI 4 PIN)
1917
21018
31119
41220
51321
61422...

75

Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or 
lost the number and unable to operate the projector, contact the service station. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
*  S h o u l d   t h e   fo u r- d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code.
While the...

76

Dimensions
Unit: inch (mm)
Appendix
161°
14.74
 (374.5)
1.38
 (35)
10.61
 (269.5)
7.01 (178)7.01 (178)
8.27 (210)
1.57 (40)
8.27 (210)3.66 (93)
22.93 (582.5)
17.56 (446)
3.26
 (82.8)
9.72
 (247)
9.9 (251.5)2.36 (60)
5.7°
9.90 (251.5)
20.58 (522.7)
1.28 (32.5)
9.90 (251.5)
5.18 (131.5)
22.87 (581)
32.11 (815.5)
6.81 (173)
Appendix 

77

Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.
Connect a RS-232C serial cross cable to SERIAL 
PORT IN on the projector and serial port on the PC.
 (See p.11)
Launch a communication software provided with PC 
and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check  : none
Stop bit   : 1
Flow control  : none
Data bit   : 8
Type the command for controlling the...

7
Status Read Command
Appendix
The command is sent from PC to the projector with 
the format below;
     'CR' [Command] 'CR'
        Command: one character (refer to the command 
table below.
The projector decodes the command and returns the 
'Charactor string' with the format below;
Format
CommandFunctionProjector 
ReturnProjector status
CR0Status Read
00Power On
80Stand-by mode
40Countdown
20Cooling down
10Power Malfunction
28Cooling down at the temperature anomaly...

KE3ASANyO Electric Co  ., Ltd .