Home > Sanyo > Projector > Sanyo Plc Xf35nl Projector User Manual

Sanyo Plc Xf35nl Projector User Manual

Here you can view all the pages of manual Sanyo Plc Xf35nl Projector User Manual. The Sanyo manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 21

21
BASIC OPERATION
TURNING ON PROJECTOR
TURNING OFF PROJECTOR
TURNING ON / OFF PROJECTOR 
Power off?
Message disappears after 4 seconds.
Connect a projectors AC Power Cord into a wall outlet and turn
MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,
and READY indicator lights GREEN.
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON. LAMP indicator dims, and Cooling Fans start
to operate. Preparation Display appears on a screen and count-
down starts.  Signal from source...

Page 22

22
KEYSTONE ADJUSTMENT
1Press KEYSTONE /button on Remote Control Unit or select
Keystone on SETTING menu.  (Refer to page 39.)  Keystone
dialog box appears.
2Correct keystone distortion by pressing KEYSTONE /button
or POINT UP/DOWN button(s).  Press KEYSTONE button or
POINT UP button to reduce upper part of image, and press
KEYSTONE button or POINT DOWN button to reduce lower
part.  
Reduce upper width with KEY STONE button or
POINT UP button.  Reduce lower width with KEY STONE button or
POINT...

Page 23

23
Press FREEZE button on Remote Control Unit to freeze picture on-screen.  To cancel FREEZE function, press FREEZE
button again or press any other button except POINT / SELECT / RIGHT CLICK /  LASER button.
PICTURE FREEZE FUNCTION
Press NO SHOW button on Remote Control Unit to black out a image.
To restore to normal, press NO SHOW button again or press any other
button except POINT / SELECT / RIGHT CLICK /  LASER button.
NO SHOW FUNCTION
Message disappears after 4 seconds.
No show
Press P-TIMER button...

Page 24

24
BASIC OPERATION
1
2
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon. 
Volume
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume.  Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound.  To
restore sound to its previous level, press MUTE button again or press...

Page 25

25
COMPUTER INPUT
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to RGB, and then press SELECT button.  
1
3
When connect a computer output [5 BNC Type (Red, Green, Blue,
Horiz. Sync and Vert. Sync.)] from a computer to R/Pr, G/Y, B/Pb, H/HV
and V jacks.
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
SELECTING COMPUTER SYSTEM
WHEN SELECT  INPUT 1 (DVI INPUT...

Page 26

26
COMPUTER INPUT
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA or UXGA (refer
to “COMPATIBLE COMPUTER SPECIFICATION” on page 27).  When selecting Computer, this projector automatically
tunes to incoming signal and projects proper image without any special setting.  (Some computers need setting manually.)
Note : Projector may display one of following messages.
When projector cannot recognize connected signal as PC
system provided in this projector,...

Page 27

27
COMPUTER INPUT
–––––––– 
(Interlace)
1024 x 768
(Interlace)
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 230 MHz of Dot Clock.
NOTE :Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x...

Page 28

28
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer.  Auto PC Adjustment function can be operated as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button twice.
This Auto PC...

Page 29

29
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed.  However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector.  If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a...

Page 30

30
NOTE :  Fine sync, Display area, Display area H, Display area V and
Full screen cannot be adjusted when “RGB”, “480p”, “575p”,
“720p (HDTV)”, “1035i (HDTV)”, “1080i50(HDTV)” or
“1080i60 (HDTV)” is selected on PC SYSTEM Menu (P26).
Selects area displayed with this projector.  Select resolution at
Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector.  Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area H...
Start reading Sanyo Plc Xf35nl Projector User Manual

Related Manuals for Sanyo Plc Xf35nl Projector User Manual

All Sanyo manuals