Sanyo Plc Xf20 Projector User Manual

41
Lamp replacement  monitor timer 
SELECTING LANGUAGE
Press the MENU button and the ON-SCREEN MENU will
appear.  Press POINT LEFT/RIGHT buttons to select
LANGUAGE  and press the SELECT button.  Another dialog box
LANGUAGE Menu will appear. 
Press the POINT DOWN button and a red-arrow icon will
appear.  Move the arrow to the language that you want to set,
and then press the 
SELECT button.
1
2
The language used in the ON-SCREEN MENU is selectable
from among English, German, French, Italian, Spanish and...

42
APPENDIX
OPERATING WIRELESS MOUSE
INSTALLATION
The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse
for most Personal Computers.  The POINT buttons and the two CLICK buttons are used for the wireless mouse
operation.
The wireless mouse is available only when PC mouse pointer is displayed on the screen.  When the menu or
the indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse
cannot be used....

43
APPENDIX
MAINTENANCE
TEMPERATURE WARNING INDICATOR
The TEMPERATURE WARNING Indicator flashes red when the internal temperature of the projector exceeds
the normal temperature.  The Indicator stops flashing when the temperature of the projector returns to normal.
When the TEMPERATURE WARNING Indicator continues to flash, check the items listed below.
The Ventilation slots of the projector may be blocked.  In such an event, reposition the appliance so that the ventilation
slots are not obstructed.
AIR...

44
APPENDIX
LAMP MANAGEMENT
This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function.  Lamp Management Function detects the status of all lamps and shows the status on screen or on
the LAMP REPLACE indicator.  This function also automatically controls the Lamp Mode when any of lamps is out for the
end of life or malfunctions. 
Lamp Status Display
Lamp Status Display appears on the screen when power switch is on or Menu Bar is...

45
APPENDIX
CLEANING THE PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
When the projector is not in use, replace the lens cover.
1
3
Lightly wipe the cleaning cloth over the lens.2
Follow these steps to clean the projection lens:
Check the number of lamp to be replaced on Lamp Status
Display.
Remove the two screws on the Lamp Cover and press...

46
Problem:
No power.
Image is out of focus.
Try these Solutions:
Plug the projector into an AC outlet.
Turn the MAIN ON/OFF switch to ON.
Press the POWER ON/OFF switch to ON.
Be sure the READY INDICATOR light is ON.
Wait 90 seconds after the projector is turned OFF before turning the projector
back on.
NOTE: After pressing the POWER ON/OFF button to OFF. The projector functions
as indicated.
1. The LAMP POWER indicator will light and the READY indicator will turn off.
2. After 90 seconds, the READY...

47
No sound.
Problem:
Check Ceiling feature.
(See SETTING section on page 39).
Picture is L/R Reversed.Check Ceiling/Rear feature.
(See SETTING section on page 39).
Picture is T/B inverted.
Check Display feature.
(See SETTING section on page 39).Some displays are not seen
during the operation.
Check audio cable connection from audio input source.
Adjust audio source.
Press the VOLUME (+) button.
Press the MUTE button.
Check the batteries.
Make sure nothing is blocking between the remote control...

48
TECHNICAL SPECIFICATIONS
Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Number of Pixels
Color System
Scanning Frequency
Motorized Lens Shift
Projection Lamp
Input 1 Jack
Other Jack
Built-in Speaker
Image Elevation Adjustment
Voltage and
Power Consumption
Storage Temperature
Remote Control Transmitters
Multi-media Projector
22.9 (581 mm) x 10 (252 mm) x 30.9 (783 mm)
78.4 Ibs (35.5 kg)
1.8 TFT Active Matrix type  x 3 panels
2,359,296 {786,432 (1,024 x 768) x 3}
6 color system (PAL,...

49
CONFIGURATIONS OF THE TERMINALS
HDB 15-PIN TERMINAL (ANALOG)
Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied).
When connecting the Macintosh computer, use MAC/VGA Adapter (supplied).
 When connecting the Analog signal from DVI terminal of the computer to this terminal, use DVI/VGA Adapter (supplied).
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
No...

50
APPENDIX
-----
RxD
TxD
-----
Ground
-----
-----
-----
1
2
3
4
5
6
7
8
Vcc
- Data
+ Data
Ground
1
2
3
4
9-----
1 2 3 4 5
6 7 8 9
Connect the serial port output terminal of the computer to this terminal with the Serial Cable (not supplied).
Pin Configuration
SERIAL PORT IN/OUT TERMINAL
USB PORT TERMINAL
Pin Configuration
Connect the USB port output terminal of the computer or peripheral equipment to this terminal with the USB port  Cable
(not supplied).
2
341