Sanyo Plc Sl20 Projector User Manual

11
Part Names and Functions
ON - OFFPOWER
KEYSTONEINPUT
WARNING
LAMP
REPLACE
MENU
VOLUME–VOLUME+SELECT
This projector has control buttons and indicators on its top.
To p
qwerty
uio
oLAMP REPLACE indicator
Turns yellow when the life of the projection lamp draws to an
end.  (p43)
yWARNING indicator
Lights red when the projector detects abnormal condition.  This
also flashes red when the internal temperature of the projector
exceeds the operating range.  (p41)
ePOWER ON–OFF button
Turns the projector on or...

12
Part Names and Functions
Remote Control
q
w
e
r
t
y
u
i
o
!0
!1
!4
!5
!6
!7
!8
!9
@0!2
!3
@1
@1RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.” Set it to “ALL OFF” for
energy saving when it is not used.  Slide this switch to the RESET to initialize the
remote control code.  (p14)
wSIGNAL EMISSION indicator
This indicator lights red while the laser beam is being emitted from the laser light
window or a signal is being sent from the remote control to the projector.
eAUTO...

13
Part Names and Functions
You can move Spotlight or Pointer of the projector with the remote control to emphasize a part of the projected image.
(See “Pointer” on page 40 for changing the patterns and sizes.)
While pressing the MENU button, hold down the NO SHOW
button for more than 7 seconds so that the Pointer function
can be available. (The Laser pointer function has switched to
the Pointer function.)1
Spotlight
Hold down the MENU button and the
NO SHOW button at the same time for
more than 7...

14
Part Names and Functions
This projector has eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other
seven codes (Code 2 to Code 8).  This switching function prevents remote control interference when operating several
projectors or video equipment at the same time.  (Change the remote control code for the projector first before changing
that for the remote control.  See “Remote control” on page 40.) 
While pressing the MENU button, press the IMAGE...

15
Part Names and Functions
To insure safe operation, please observe the following precautions :
Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at the same time.
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture, or heat.
Do not drop the remote control.
If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
Risk of explosion if battery is replaced by an...

16
Installation
Projection angle can be adjusted up to 11.8 degrees with the adjustable feet. 
Lift the front of the projector and pull the feet lock latches on
both sides of the projector.1
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to adjust the position and tilt. 2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can be adjusted
by menu operation.  (p20,...

17
Installation
Connecting to a Computer
ON ON
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
MCI
(MONO)
(VARIABLE)
AUDIO  OUT
ON
1DIPON
OFF
23456
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF
ON
ONOFF OFF OFF
OFF OFF OFF
OFF OFF OFF34 56
OFF OFF ON ON 21 MODE (1152 x 870)
ON ON
ON
ON OFF
OFF12
ON ON
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
DVI-VGA Cable...

18
Installation
Connecting to Video Equipment
COMPUTER  IN  1DVI - I
MONITOR  OUT
S-VIDEO
COMPUTER IN 2 / COMPONENT IN / 
COMPUTER / COMPONENT
AUDIO  IN
AUDIO  IN
RVIDEOLUSB
SERVICE PORT 
RESET
MCI
(MONO)
(VARIABLE)
AUDIO  OUT
Video Source (example)
Video Cassette RecorderVideo Disc Player
S-VIDEO
Cable 
✽
Audio AmplifierAudio Speaker 
(stereo) Audio Cable 
(Stereo) 
✽
Terminals 
of the Projector
S-VIDEO
Output
Audio Input
• Video Cable (RCA x 1) ✽
• S-VIDEO Cable ✽
• Audio Cables (Mini Plug (stereo) x 2...

19
Basic Operation
Connect the projectors AC power cord into an AC outlet.  The
POWER indicator flashes red in a moment and turns on red. 
Press the POWER ON-OFF button on the top control or on the
remote control.  The POWER indicator turns green, and the
cooling fans start to operate.  The preparation display appears on
the screen and the count down starts. 
2
3
Press the POWER ON-OFF button on the top control or on the
remote control, and a message Power off? appears on the
screen.  
Press the POWER...

20
Press the FREEZE button on the remote control to freeze the picture
on the screen.  To cancel the FREEZE function, press the FREEZE
button again or press any other button.
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
Basic Operation
• The arrows are white when there is no correction.
• The arrows disappear at the maximum correction.
• The direction of the arrow being corrected turns red.
• If you press the KEYSTONE button on the top control
or on the...