Sanyo Plc Ef60a Projector User Manual

11
Preparation
Top Control
LENS SHIFTMENU
CANCEL
SELECT ZOOM
FOCUSSHUTTERINPUT
INFORMATION AUTO PC ADJ.
POWER P
qwerty
oi
u
uINPUT button
Switches input sources. (p.30)
yAUTO PC ADJ. button
Operates the Auto PC adjustment function. (p.30)
eCANCEL button
Cancels the selection and returns to the previous menu.  
t
INFORMATION button
Displays the projector information. (p.30) 
wMENU button
Opens or closes the On-Screen Menu. (p.33, 34)
oPOWER ON-OFF button
Turns the projector on or off. (p.27, 28)
iSHUTTER...

12
Preparation
ANALOG OUT
INPUT 3 INPUT 1
INPUT 2
ANALOG IN
DIGITAL (DVI-D)
VIDEO/Y    Cb/Pb          Cr/PrG                B               R            H/V               V
VIDEO/Y   Cb/Pb     Cr/PrS-VIDEO
Terminals
q
w
er
eINPUT 3 terminals
VIDEO/Y, Cb/Pb, and Cr/Pr
Connect video or component output signal (Y, Cb/Pb,
and Cr/Pr) from video equipment to these jacks with a
video cable (RCA-type). (p.23, 24)
S-VIDEO
Connect S-Video output signal from video equipment
to this jack. (p.23)
rINPUT 2 terminals...

13
Preparation
A built-in micro processor which controls this unit may occasionally
malfunction and needs to be reset. This can be done by pressing the RESET 
button with a pen, which will shut down and restart the unit. Do not use the
RESET function excessively.
q
erty
uSERIAL PORT IN
When controling the projector from a computer, connect
the computer to this terminal with a serial cross cable
(commercially available).
tUSB (Series B)
This port is used for the projector maintenance.
ySERIAL PORT OUT...

14
Preparation
Remote Control 
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOMFOCUS ON-OFF
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTE
VOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
q
w
u
i
e
r
y
!0
o
oZOOM buttons
Adjust zoom of the image. (p.29)rCONTROL PAD (semiconductive touchpad)
- Selects an item or adjusts the value in the On-Screen
Menu.
- Pan the image in the Digital zoom + mode. (p.32)
w
KEYSTONE...

15
Preparation
!1SCREEN button
Selects screen sizes. (p.31)
!2
INPUT 1-3 buttons
Selects input source (INPUT 1 - INPUT 3). (p.30)
!0AUTO PC button
Operates the Auto PC adjustment. (p.30)
qMENU button
Opens or closes the On-Screen Menu. (p.33, 34)
wFREEZE button
Freezes the projected picture. (p.31)
!4REMOTE RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.”
Set it to “ALL OFF” for power saving when it is not
used. Slide this switch to “RESET” by holding down the
CH and ID...

16
Preparation
This wireless remote control uses radio frequency signal. You can switch four frequency channels prepared and select a
remote control ID from eight IDs. The Remote Control Channel selection prevents radio frequency interference from the
other equipment and the Remote Control ID selection allows you to operate several projectors with their respective remote
controls without mutual interference among those projectors.
Wired Remote Control Transmitter
The remote control can be used as a wired...

17
Preparation
Remote Control Battery Installation
To insure safe operation, please observe the following precautions:
●Use (2) AA or LR6 type alkaline batteries.
●Always replace the batteries in sets.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control to moisture, or heat.
●Do not drop the remote control.
●If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
●Risk of explosion if battery is...

18
Install the projector in a safe place.  Before installation, read Safety
Instructions thoroughly and check the installation place. Install the
projector in a place with sufficient strength to support the
projectors weight. Installation on an unstable stand, cart, or ceiling
may cause serious injury or accidents.  
Do not place the projector where is extremely hot and humid. Do
not place the projector where is dusty and smoky. When installing
the projector in dusty and smoky places or in a place for a...

19
Installation
Adjustable feet Lens shift feature is provided to move the position of the projected image vertically by 50% and horizontally by 10%
respectively without any image distortion.
✽Lens shift range varies depending on lens and projectors. The range in this manual is the case of LNS-W04.
Level Adjustable Feet
This projector has four level adjustable feet. The projection angle
can be adjusted by rotating each foot. Adjust the four feet to
obtain best position of the projected image and make the...

20
To POWER CORD
CONNECTOR on a
projector.
Projector sideAC Outlet side
Ground
NOTE ON POWER CORD
AC power cord must meet requirement of the country where you use the projector.
Confirm an AC plug type with the chart below and a proper AC power cord must be used.
If the supplied AC Power Cord does not match your AC outlet, contact your sales dealer.
To the AC Outlet.(120 V AC)
For Continental EuropeFor the U.S.A. and CanadaFor the U.K.
To the AC Outlet.(200 - 240 V AC)
To the AC Outlet.(200 - 240 V AC)...