Sanyo Pdg Dht8000l Projector User Manual

							
81

Appendix
The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMP 1/2REP.
orange
If the Filter counter reached a time set in the timer 
setting, a Filter replacement icon (Fig.2) appears 
on the screen and the WARNING FILTER indicator 
on the top panel lights up. Replace the filter as 
soon as possible. If the filter is out of scroll and the 
projector reaches a time set in the timer setting, Fig. 
3 appears on the screen and the WARNING FILTER 
indicator lights up. Replace the filter cartridge as 
soon as possible.
If the filter is clogged and no scroll is left in the filter 
cartridge, a Filter cartridge replacement icon (Fig.4) 
appears on the screen and the WARNING FILTER 
indicator lights up. Replace the filter cartridge as 
soon as possible.
✔Note: • Fig.2, Fig.3 and Fig.4 icon will not appear when the Display function is set to “Off” (p.49), or during “Freeze” (p.30).
The projector detects an abnormal condition during 
filter scroll.
The projector is being cooled down after detecting 
an abnormal condition during filter scroll.
The projector has been cooled down enough and is 
in the stand-by mode after detecting an abnormal 
condition during filter scroll.
The filter cartridge is removed while the projector is 
on.
The projector is turned on without installing the filter 
cartridge, and then the filter cartridge is installed 
while the projector is on.
The projector detects an abnormal condition and 
cannot be turned on. Unplug the AC power cord and 
plug it again to turn on the projector. If the projector 
is turned off again, unplug the AC power cord and 
contact the dealer or the service center. Do not 
leave the projector on. It may cause an electric 
shock or a fire hazard.
The shutter is out of control. 
The shutter is out of control. (The projector is in the 
cooling mode.)
The shutter is out of control. (The projector is in the 
stand-by mode.) In that case, contact the service 
center immediately.
Fig .    Filter replacement icon
Fig .4    Filter cartridge replacement icon
Fig .
✽
✽✽
✽
✽
✽✽✽✽✽
✽
✽
✽✽
✽
✽
✽✽✽✽
✽
✽ 
						

							
8

Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below 
and less than 230 MHz of Dot Clock.
Appendix
✽“True”  cannot  be  selected  when WUXGA1, WXGA+2,  UXGA1,  UXGA2,  UXGA3,  UXGA4  and  UXGA5  are 
selected. (p.40)
ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
VGA 1640x48031.470 59.880 
VGA 2720x40031.470 70.090 
VGA 3640x40031.470 70.090 
VGA 4640x48037.860 74.380 
VGA 5640x48037.860 72.810 
VGA 6640x48037.500 75.000 
VGA 7640x48043.269 85.000 
MAC LC13640x48034.970 66.600 
MAC 13640x48035.000 66.670 
480p640x48031.470 59.880 
575p768x57531.250 50.000 
575i768x576 (Interlace)15.625 50.000 
480i640x480 (Interlace)15.734 60.000 
SVGA 1800x60035.156 56.250 
SVGA 2800x60037.880 60.320 
SVGA 3800x60046.875 75.000 
SVGA 4800x60053.674 85.060 
SVGA 5800x60048.080 72.190 
SVGA 6800x60037.900 61.030 
SVGA 7800x60034.500 55.380 
SVGA 8800x60038.000 60.510 
SVGA 9800x60038.600 60.310 
SVGA 10800x60032.700 51.090 
SVGA 11800x60038.000 60.510 
MAC 16832x62449.720 74.550 
XGA 11024x76848.360 60.000 
XGA 21024x76868.677 84.997 
XGA 31024x76860.023 75.030 
XGA 41024x76856.476 70.070 
XGA 51024x76860.310 74.920 
XGA 61024x76848.500 60.020 
XGA 71024x76844.000 54.580 
XGA 81024x76863.480 79.350 
XGA 91024x768 (Interlace)36.000 87.170 
XGA 101024x76862.040 77.070 
XGA 111024x76861.000 75.700 
XGA 121024x768 (Interlace)35.522 86.960 
XGA 131024x76846.900 58.200 
XGA 141024x76847.000 58.300 
XGA 151024x76858.030 72.000 
MAC 191024x76860.240 75.080 
SXGA 11152x86464.200 70.400 
SXGA 21280x102462.500 58.600 
SXGA 31280x102463.900 60.000 
SXGA 41280x102463.340 59.980 
SXGA 51280x102463.740 60.010 
SXGA 61280x102471.690 67.190 
SXGA 71280x102481.130 76.107 
SXGA 81280x102463.980 60.020 
ON-SCREEN
 DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
SXGA 91280x102479.976 75.025 
SXGA 101280x96060.000 60.000 
SXGA 111152x90061.200 65.200 
SXGA 121152x90071.400 75.600 
SXGA 131280x1024 (Interlace)50.000 86.000 
SXGA 141280x1024 (Interlace)50.000 94.000 
SXGA 151280x102463.370 60.010 
SXGA 161280x102476.970 72.000 
SXGA 171152x90061.850 66.000 
SXGA 181280x1024 (Interlace)46.430 86.700 
SXGA 191280x102463.790 60.180 
SXGA 201280x102491.146 85.024 
SXGA+ 11400x105063.970 60.190 
SXGA+ 21400x105065.350 60.120 
SXGA+ 31400x105065.120 59.900 
SXGA+ 41400x105064.030 60.010 
SXGA+ 51400x105062.500 58.600 
SXGA+ 61400x105064.74459.948
SXGA+ 71400x105065.31759.978
MAC 211152x87068.680 75.060 
MAC1280x96075.000 75.080 
MAC1280x102480.000 75.080 
WXGA 11366x76848.360 60.000 
WXGA 21360x76847.700 60.000 
WXGA 31376x76848.360 60.000 
WXGA 41360x76856.160 72.000 
WXGA 61280x76847.776 59.870 
WXGA 71280x76860.289 74.893 
WXGA 81280x76868.633 84.837 
WXGA 91280x80049.600 60.050 
WXGA 101280x80041.200 50.000 
WXGA 111280x80049.702 59.810 
WXGA 121280x80063.98060.020
WUXGA 11920x120074.556 59.885 
WUXGA 21920x120074.038 59.950 
WSXGA+ 11680x105065.290 59.954 
WXGA+ 11440x90055.935 59.887 
WXGA+ 21440x90074.918 60.000 
UXGA 11600x120075.000 60.000 
UXGA 21600x120081.250 65.000 
UXGA 31600x120087.500 70.000 
UXGA 41600x120093.750 75.000 
UXGA 51600x1200106.250 85.000 
720p1280x72045.000 60.000 
720p1280x72037.500 50.000 
1035i1920x1035 (Interlace)33.750 60.000 
1080i
1920x1080 (Interlace)33.750 60.000 
1920x1080 (Interlace)28.125 50.000 
✽
✽
✽
✽
✽
✽
✽ 
						

							
8

Appendix
ON-SCREEN DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
1080p
1920x108033.75030.000
1920x108028.12525.000
1920x108027.00024.000
1920x108067.50060.000
1920x108056.25050.000
1080psf/301920x108033.75060.000
1080psf/251920x108028.12550.000
1080psf/241920x108027.00048.000
When an input signal is digital from the DVI or HDMI terminal, refer to the chart below.
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
D-VGA640x48031.470 59.940 
D-480p720x48031.470 59.880 
D-575p720x57531.250 50.000 
D-SVGA800x60037.879 60.320 
D-XGA1024x76843.363 60.000 
D-WXGA 11366x76848.360 60.000 
D-WXGA 21360x76847.700 60.000 
D-WXGA 31376x76848.360 60.000 
D-WXGA 41360x76856.160 72.000 
D-WXGA 51366x76846.500 50.000 
D-WXGA 61280x76847.776 59.870 
D-WXGA 71280x76860.289 74.893 
D-WXGA 81280x76868.633 84.837 
D-WXGA 91280x80049.600 60.050 
D-WXGA 101280x80041.200 50.000 
D-WXGA 111280x80049.702 59.810 
D-WXGA 121280x80063.98060.020
D-SXGA 11280x102463.980 60.020 
D-SXGA 21280x102460.276 58.069 
D-SXGA+ 11400x105063.970 60.190 
D-SXGA+ 21400x105065.350 60.120 
D-SXGA+ 31400x105065.120 59.900 
D-SXGA+ 61400x105064.74459.948
D-SXGA+ 71400x105065.31759.978
D-WUXGA 21920x120074.03859.950
D-WSXGA+ 11680x105065.290 59.954 
D-WXGA+ 11440x90055.935 59.887 
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
D-720p1280x72045.000 60.000 
D-720p1280x72037.500 50.000 
D-1035i1920x1035 
(Interlace)33.750 60.000 
D-1080i
1920x1080 
(Interlace)33.750 60.000 
1920x1080 
(Interlace)28.125 50.000 
D-1080psf/301920x108033.750 60.000 
D-1080psf/251920x108028.125 50.000 
D-1080psf/241920x108027.000 48.000 
D-1080p
1920x108033.75030.000
1920x108028.12525.000
1920x108027.00024.000
1920x108067.50060.000
1920x108056.25050.000
✔Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
•Specifications are subject to change without notice.
•  You might be able to project images even when signals other than above are inputted, however the functions of the 
projector could be limited.
•  Depending on your PC settings, the digital signals of your PC may not be projected correctly. In such a case, confirm 
your PC settings.
•  When you project a DVI signal, connect the cables, turn the projector on, then select the input. Finally, turn on your PC. 
Be sure to follow this procedure, other wise an image may not be projected on the screen. If an image is not projected 
correctly, restart your PC.
•  Do not disconnect the cable while the projector is running. If the cable has been disconnected and then reconnected, an 
image may not be correctly projected. 
						

							
84

Appendix
On-BoardOptional Interface Board
Input1Input2Dsub-DVIComponent-S-videoSDI
Analog PCScartDigitalAnalog PC
ComponentVideo/S-VideoAnalog PCScartDigitalAnalog PC
ComponentVideo/S-videoDigital
On-BoardInput1
Analog PCo    o    o    o    o    o    o    o    o    o    o    
Scarto    o    o    -        -        -        o    -        -        -        o    
Digitalo    o    o    o    o    o    -    -        o    o    o    -        
On-BoardInput2
Analog PCo    o    o    o    o    o    o    o    o    o    
Componento    o    o    o    o    o    o    o    o    o    
Video/S-Videoo    -        o    -        -        o    -        -        -        o    
List of Picture in Picture
 o : Picture in Picture combinations are enabled
 - : Picture in Picture combinations are disabled
✔Note:
•  
As for Input 3 and Input 4, combination of digital signals for Main picture and Sub picture is not available.
•   
When the input signal(s) is/are incompatible, X mark will be displayed on the Main/Sub picture.
•   Depending on the frequency or signal type of PC/AV input, 
the display resolution may be lowered or images may not be 
displayed on the Main/Sub picture.
  
    •  Inputting PC analog signals: Between 100-160 MHz
    •  Inputting AV analog signals: 1080p
  
    •  Inputting PC analog signals: More than 160MHz
    •  Inputting PC digital signals: More than 100MHz
    •  Inputting AV digital signals: 1080p
When using the optional board (DVI) “ POA-AMDADI”, refer to the chart on the previous page.
When using the optional board (Dual SDI) “POA-AMD17SDID”, refer to the chart below.
Supported Signal Format for Optional Board
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
1035i1920x1035 
(Interlace)33.750 60.000 
1080i
1920x1080 
(Interlace)33.750 60.000 
1920x1080 
(Interlace)28.125 50.000 
720p/601280x72045.00060.000
720p/501280x72037.50050.000
ON-SCREEN 
DISPLA yRESOLUTION H-Freq .(kHz)V-Freq .(Hz)
1080psf/301920x108033.750 60.000 
1080psf/251920x108028.125 50.000 
1080psf/241920x108027.000 48.000 
1080p/301920x108033.75030.000
1080p/251920x108028.12525.000
1080p/241920x108027.00024.000 
						

							
85

Technical Specifications
Mechanical Information 
 Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  15.75” x 9.55” x 20.61” (400.0 mm x 242.5 mm x 523.5 mm)
 
  Net Weight  43.2 lbs (19.6 kg)
 
  Feet Adjustment  ± 5˚           
              
DLP Chip 
 Projection System  0.95” Single DLP chip, High brightness color wheel x 2  
  Number of Pixels  2,073,600 pixels (1,920 x 1,080 dots)           
             
Signal Compatibility 
 Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N 
  High Definition TV Signal  480i, 480p, 575i, 575p, 720p, 1035i, 1080p, and 1080i
 
 Input Scanning Frequency  H-sync. 15 kHz–120 kHz, V-sync. 48 Hz–120 Hz         
 
Optical Information 
 Projection Lamp  330 W UHP lamp x 2           
  
Interface
 Input 1  DVI-D Terminal (Digital), Mini D-Sub 15-pin Terminal (Analog), HDMI (v.1.3 with Deep Color) 
  Input 2  BNC Type x 5 (VIDEO/Y/G, B/Pb/Cb, R/Pr/Cr, H/HV and V), S-Video     
  Input 3  Vacant           
  Input 4  Vacant           
  Monitor Output  Mini D-sub 15 pin           
  Other Jacks  Serial port in (D-sub 9), Serial port out (D-sub 9), USB port, LAN port (RJ45), 
 
    and Wired Remote Jack   
 
 
Power
 Voltage and Power Consumption  AC 100–120 V (10.0A Max. Ampere), 50/60 Hz (The U.S.A and Canada) 
    AC 100-240 V (10.0-5.0A Max. Ampere), 50/60 Hz (For other countries)     
 
Operating Environment
 Operating Temperature  41˚F–104˚F (5˚C–40˚C) 
  Storage Temperature  14˚F–140˚F (-10˚C–60˚C)
 
 
Remote Control 
  Battery  AA or LR6 Type x 2           
  Operating Range  16.4’ (5 m/±30˚)
 
  Dimensions  1.79” (W) x 1.03” (H) x 6.24” (D) (45.5 mm x 26.2 mm x 158.5 mm)     
  Net Weight  4.1 oz (117 g) (including batteries)
 
 
Accessories
 q Owner’s Manual (CD-ROM) 
 q Quick Reference Guide 
 q AC Power Cord 
 q Remote Control and Batteries 
 q VGA Cable
 q PIN Code Label
 q Fixing bracket for power cord
 q Rich color reproduction color wheel x 2
 q Cable tie x 3
 q Real Color Manager Pro (CD-ROM)  
Appendix 
						

							
86

Optional Parts
     Model No.
Optional Interface Board (DVI)    
: POA-AMD23ADI
Optional Interface Board (5-BNC)    
: POA-AMD25VD3
Optional Interface Board (Dual-SDI) 
: POA-AMD17SDID
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. 
to the sales dealer.
Appendix
l  The specifications are subject to change without notice.
l   Each projector has its own characteristics.
       
When projecting with several projectors on the same screen or side by side, you may recognize different white balance 
and color uniformity on each projector.
✔Note:
•   Between the two features of the provided Real Color Manager Pro (CD-ROM); "Color Correction" and "Gamma Correction", "Color Correction" is not available with this projector.  
						

							
87

Configurations of Terminals
ANALOG (Mini D-sub 15 pin)
512341096781514131112
CONTROL PORT CONNECTOR (D-sub 9 pin)
DIGITAL DVI-D (DVI 4 PIN)
1917
21018
31119
41220
51321
61422
71523
81624
USB CONNECTOR (Series B)
2
3 4
1
Appendix
Input
Output
13579111315171918161412108642
HDMI (19 pin Type A)
8 7 6 5 4 3 2 1
LAN TERMINAL (Rj-45)
1TX+
TX–
RX+
4- - -
5- - -
6RX–
7- - -
8- - -
Serial
1- - -
RXD
TXD
4- - -
5SG
6- - -
7- - -
8- - -
9- - -
1Vcc
– Data
+ Data
4Ground
1.M.D.S. Data2–9T.M.D.S. Data1–17T.M.D.S. Data0–
.M.D.S. Data2+10T.M.D.S. Data1+18T.M.D.S. Data0+
.M.D.S. Data1Shield11T.M.D.S. Data1 Shield19T.M.D.S. Data0 Shield
4- - - 1- - -0
5- - -1- - -1
6DDC Clock14+5V PowerT.M.D.S. Clock Shield
7DDC Data15Ground (for +5V)T.M.D.S. Clock+
8- - -16Hot Plug Detect 4T.M.D.S. Clock–
1T.M.D.S. Data 2+ Input11Ground (T.M.D.S. Clock)
Ground(T.M.D.S. Data 2) 1T.M.D.S. Clock– Input
T.M.D.S. Data 2– Input1- - -
4T.M.D.S. Data 1+ Input14- - -
5Ground (T.M.D.S. Data 1)15SCL
6T.M.D.S. Data 1– Input16SDA
7T.M.D.S. Data 0+ Input17Ground (DDC/CEC)
8Ground (T.M.D.S. Data 0)18+5V Power
9T.M.D.S. Data 0– Input19Plug insert detection
10T.M.D.S. Clock+ Input
1Red Input9+5V Power
Green Input10Ground (Vert. sync)
Blue Input11Ground
4- - -1DDC data
5Ground (Horiz. sync.) 1Horiz. sync.
6Ground (Red)14Vert. sync.
7Ground (Blue)15DDC Clock
8Ground (Green)
1Red Output9- - -
Green Output10Ground (Vert. sync)
Blue Output11- - -
4- - -1- - -
5Ground (Horiz. sync.) 1Horiz. sync. Output
6Ground (Red)14Vert. sync. Output
7Ground (Blue)15- - -
8Ground (Green) 
						

							
88

Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or 
lost the number and unable to operate the projector, contact the service center. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
*  S h o u l d   t h e   fo u r- d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code.
While the projector is locked with the PIN code...
PIN Code Lock No.
Logo PIN Code Lock No.
PIN Code Number Memo
Appendix 
						

							
89

Dimensions
Unit: inch (mm)
Appendix
0.28(7
.0)
9.21(234.0
)
9.55(242.5
)
4.45(113.0)
20.47(520.0
)
20.61(523.5
)
15.75(400.0)
8.31(211.0
)
5.0º
5.0º
19.96(507.1)
96.0º
6.02(153.0)5.63(143.0)
6.81(173.0)6.81(173.0)
5.08(129.0
)
4.65(118.0)
2.64(67.0
)
4.25(108.0
)
12.48(317.0
)
5.79(147.0)4.92(125.0)
6.50(165.0)6.50(165.0)
14.29(363.0
)
Screw Holes for Ceiling MountScrew: M8Depth: 0.393 (10.0) 
						

							
90

Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.
Connect a RS-232C serial cross cable to SERIAL 
PORT IN on the projector and serial port on the PC.
 (See p.11)
Launch a communication software provided with PC 
and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check  : none
Stop bit   : 1
Flow control  : none
Data bit   : 8
Type the command for controlling the projector and 
then enter the "Enter" key. 
Example
When you want to change the input to INPUT 2, 
Type 'C' '0' '6' 'Enter'. 
✔Note:
• The default of the baud rate is set to 19200 bps. If an 
error occurs in the communication, change the serial 
port and the communication speed (baud rate).
•Enter with ASCII 64-byte capital characters and one-
byte characters.
The command is sent from PC to the projector with 
the format below;
      'C' [Command] 'CR'
        Command: two characters (refer to the 
command table below.
-The projector decodes the command and returns the 
'ACK' with the format below;
     'ACK'  'CR'
-When the projector cannot decode the command, it 
returns with format below.
     ‘?’  ‘CR’ 
Format
Operation
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the projector OFF 
(immediately OFF)
C05Select Input 1
C06Select Input 2
C07Select Input 3
C08Select Input 4 
C0DVideo mute ON
C0EVideo mute OFF
C0FScreen normal size
C10Screen full size
C1CMenu ON
C1DMenu OFF
C3APointer RIGHT
CommandFunction
C3BPointer LEFT
C3CPointer UP
C3DPointer DOWN
C3FEnter
C46Zoom DOWN
C47Zoom UP
C4AFocus DOWN
C4BFocus UP
C5DLens shift UP
C5ELens shift DOWN
C5FLens shift LEFT
C60Lens shift RIGHT
C89Auto PC Adj.
C8EKeystone UP
C8FKeystone DOWN
C90Keystone RIGHT
C91Keystone LEFT