Sanyo Pdg Dht8000l Projector User Manual

							
51

Setting
Picture in Picture
This function is used to project two videos simultaneously by 
placing a separate small sub screen within or next to the main 
screen.
Use the Point ed buttons to move the red frame pointer to 
Picture in Picture and then press the SELECT button to display 
a dialog box. You can also display the dialog box by pressing 
and holding the PIP button on the remote control for more 
than 3 seconds.
Use the Point 7 8 buttons to adjust the setting value.
  Picture in Picture
. . . 
Show the selected mode (Off/User1-5) 
and its status (Stored /Free/Adj.).
          'User1' and 'User2' have stored default 
values. See page 30 for details.
  Mode
 . . . . . .P in P:  Provide the images of Main picture and 
Sub picture at the ratio of 16:9.
P by P:  Provide the images of Main picture and 
Sub picture at the ratio of 4:3.
  Main picture/
  Sub picture
 . . .
    Input:    Select an input from Input 1-4.
  Source:    Select an input source. The display varies 
depending on the selected input.
Size:    Select the display size. Main picture can 
be changed between 10 and 100%, and 
Sub picture can be changed between 10 to 
50% in increments of 10%. When P by P is 
selected in Mode, the projection size is fixed 
to 50%.
Position:   Press the SELECT button at Position and 
the display position setting screen appears. 
Use the Point ed7 8 buttons to adjust the 
display position of active frame indicated 
in white. The frame will disappear after 10 
seconds or when the SELECT button is 
pressed.
  Frame Lock
 . . . Set the Frame Lock to Main picture or Sub 
picture.
  Reset
 . . . . . . . .  
Press the SELECT button at Reset to display 
a confirmation box. To reset, press the 
SELECT button at [Yes].
  Mode free
 . . . .   
Delete the data stored in the Mode and 
return to the ‘Free‘ state. Use the Point 7 
8 buttons to select Mode free and press 
the SELECT button to show the 'Where 
to free?' dialog box. Move the red arrow 
pointer to one of the mode (Mode 1 - 5) 
which you want to delete and press the 
SELECT button. Then the Confirmation box 
appears. To delete, select [Yes].
  Store
 . . . . . . . .  
Store the adjusted data in the User 1–5. 
Use the Point 7 8 buttons to select Store 
and press the SELECT button to show the 
‘Where to store?‘ dialog box. Move the red 
arrow pointer to one of the mode (Mode 1 
- 5) in which you want to store and press the 
SELECT button. Then the Confirmation box 
appears. To store adjusted data, select [Yes].
  Quit
 . . . . . . . . . Exit the Picture in Picture menu.
Picture in Picture
Use the Point 7 8 buttons to adjust the setting value.
Selected ModeStatus (Stored /Free/
Adj.) of the selected mode.
Close this dialog box.
To store the adjusted data .
Confirmation box appears and then select [Yes].
This mode has stored data.
Vacant
✔Note:
•  
The  Picture  in  Picture  function  is  not  available  depending 
on the input signals and the selected input terminals. Refer 
to ‘List of Picture in Picture‘ for details. (p.84)
•   
When  the  input  signal(s)  is/are  incompatible,  X  mark  will 
be displayed on the Main/Sub picture.
•   
While  the  Main  and  Sub  pictures  are  being  displayed, 
System,  Image  select,  Image  adj.,  Screen  menus  (except 
for  ‘Keystone’,  ‘Ceiling’  and  ‘Rear’),  and  DynamicBlack are 
inoperative.
  •   ‘Progressive’ and ‘Noise reduction’ functions are fixed to 
‘Off’ during the Picture in Picture operation. Therefore, the 
image may become grainy depending on the input signal.
Active frame (White)
Center line display 
						

							
5

Setting
Edge blending
This function allows multiple projector images to be seamlessly 
overlapped.
Use the Point ed buttons to move the red frame pointer to 
Edge blending and then press the SELECT button to display a 
dialog box. Use the Point ed7 8 buttons to adjust the setting 
value.
 Edge blending 
 . .   Set to ‘On‘ to activate the Edge blending 
function.
  Width
 . . . . . . . . .  
Adjust the width of correction.
            Right/Left:  Set the width. (from 0 to 960).
         Top/Bottom:  Set the width. 
(from 0 to 540).
 Black level . . . . .  
Adjust the black level of projected image.
         All:   
The values of R, G, and B will be 
changed simultaneously.
  R/G/B:   
Adjust the value (± 127).
  Test pattern
 . . . .  
Select ‘On‘ to display a suitable pattern.
  Menu off
    . . . . .  
Close the menu temporarily.
  Reset
 . . . . . . . . .  
Select ‘Reset’ and press the SELECT button. 
Then ‘Return to factory default of Edge 
Blending?‘ message appears. To reset, press 
the SELECT button at [Yes].
  Quit
 . . . . . . . . . .  
Exit the Edge blending menu.
Edge blending
Close this dialog box.
Color matching
When multiple sets are used simultaneously, this projector 
allows the user to correct the difference of colors among the sets.
Use the Point ed buttons to move the red frame pointer to 
Color matching and then press the SELECT button to display a 
dialog box. Use the Point ed7 8 buttons to adjust the setting 
value.
 Color matching
 . . . .   Set to ‘On‘ to activate the Color matching 
function. When the color matching is set 
to ‘Off‘, all items except for Advanced 
color matching are displayed in grayout 
and cannot be adjusted.
  Color adjustment
 . . .  
Adjust the color setting of Red/Green/
Blue/White. The chromatic coordinate 
(X,Y) of Red, Green, Blue, and White can 
be adjusted respectively. The adjustable 
range is from 0.000 to 1.000.
  Auto test pattern
 . . .  
Select ‘On‘ to display a suitable pattern 
when setting items.
  Reset 
 . . . . . . . . . . . .  
Select ‘Reset’ and press the SELECT 
button. Then the confirmation message 
appears. Press the SELECT button at [Yes]  
to reset to the previously stored values.
  Store 
 . . . . . . . . . . . .  
Select ‘Store’ and press the SELECT 
button to display the Confirmation box. To 
store adjusted data, select [Yes].
 Advanced 
  color matching
 . . . . .  
Select ‘Advanced color matching’ and 
press the SELECT button for more 
detailed settings. Another setting screen 
will appear. 
Color matching
Close this dialog box.
✔Note:
•  
The overlapping areas might become uneven depending on 
the images. In such a case, it is recommended to decrease 
the  contrast  of  the  images  in  the  Image  Adjust  Menu  or 
set the BrilliantColor function to ‘Off’.
•  
See “How  to  adjust  multiple  screens”  on  pages  92-93  for 
further information. 
						

							
5

Setting
 Advanced 
  color matching 
 . . . . .  
Set to ‘On‘ to activate the ‘Advanced color 
matching’. When it is set to ‘Off‘, all items 
except for ’Test pattern’ are displayed in 
grayout and cannot be adjusted.
  Measured
 . . . . . . . .  
When using the color wheel set optimized 
for high brightness, the chromatic coordinate 
(X,Y) and the brightness (L) of Red, Green, 
Blue, Half white, and White are displayed 
(Fig.1). When using the color wheel set 
optimized for rich color reproduction, the 
chromatic coordinate (X,Y) and the brightness 
(L) of Red, Green, Blue, and White are 
displayed (Fig.2).
      Information:   Select ‘Information’ and press the SELECT 
button to display the information dialog box 
(Fig.3). Measured information display can be 
used to confirm the current setup condition of 
the Image select menu and the color wheels.
  Target 
 . . . . . . . . . . .  
Adjust the chromatic coordinate (X,Y) and 
the gain value (g) of Red, Green, Blue, Cyan, 
Magenta, Yellow, and White. Use the Point 
ed7 8 buttons to move the red frame 
pointer to an item of which you want to adjust 
the value and then press the SELECT button. 
Use the Point ed buttons to adjust the value. 
To move to the next digit, use the Point 7 8 
buttons. Press the SELECT button to set the 
value.
  Auto test pattern
 . . .  
Select ‘On‘ to display a suitable pattern when 
setting items.
  Factory default
 . . . .  
Select ‘Factory default’ and press the SELECT 
button. Then ‘Return to factory default of 
Color matching?‘ message appears. To reset 
the selected Measured value and Target 
value, select [Yes]. Then, the confirmation box 
appears. Press the SELECT button at [Yes] 
again.
  Reset 
 . . . . . . . . . . . .  
Select ‘Reset’ and press the SELECT button. 
Then the confirmation message appears. 
Press the SELECT button at [Yes]  to reset to 
the previously stored values.
  Store 
 . . . . . . . . . . . .  
Select ‘Store’ and press the SELECT button. 
Then the Confirmation box appears. To store 
adjusted data, select [Yes].
  Test pattern
 . . . . . . .  
When using the color wheel set optimized for 
high brightness, use the Point ed buttons to 
select from (Measured) Red/Green/Blue/Half 
white/White/(Target) Red/Green/Blue/ Cyan/
Magenta/Yellow/White.
        When using the color wheel set optimized 
for rich color reproduction, use the Point ed 
buttons to select from (Measured) Red/Green/
Blue/White/(Target) Red/Green/Blue/Cyan/
Magenta/Yellow/White.
  Menu off 
. . . . . . . .Close the menu temporarily.
  Quit
 . . . . . . . . . . . . .Exit the Color matching menu.
DynamicBlack
DynamicBlackTM improves  the  black  level  of  the  projector.  Black 
level is the darkest part of a picture and varies between viewing 
devices and environments. Set DynamicBlack Off/Low/High.
Advanced color matching
Close this dialog box.
✔Note:
  •   In the Measured information dialog box, ‘Standard’ 
indicates all the Image select menus other than 
‘Dynamic’.
Fig .1   For high brightness color wheel
Fig .
   For rich color reproduction color wheel
Fig .
   Measured information dialog box 
						

							
54

This function allows you to customize the screen logo with Logo 
select, Capture, and Logo PIN code lock functions.
Logo
✔Note:
• Before capturing an image, select “Standard” in the Image Select Menu to capture a proper image. (pp.39, 43)
•  A signal from a computer can be captured up to 1920 x 
1080 dots.•Certain signals may not be captured properly.
• When capturing the image that has been adjusted by the 
Keystone function, the adjusted data is automatically reset and the projector captures an image without keystone correction. 
•  When  starting  to  capture  a  new  image,  the  previously 
stored image is cleared even if you cancel the capturing.
•  Once  you  exit  the  Logo  Menu  after  setting  the  Logo  lock 
to  "On,"  you  are  required  to  enter  the  PIN  code  ever y attempting to change the Logo setting.
•  “ U s e r ”   c a n n o t   b e   s e l e c t e d   w h e n   t h e   i m a g e   i s   n o t 
captured.
This function decides on the starting-up display from 
among the following options.
  Off
  . . . .  Show the countdown display only.
  Default
  .  Show the factory-set logo.
  User
 . . .  Show the image you captured.
Capture
Logo select
Logo
✔Note:
•  When “On” is selected in the Logo PIN code lock function, 
Logo select and Capture functions cannot be selected.
This function enables you to capture an image being 
projected to use it for a starting-up display or interval of 
presentations.
Select Capture and press the SELECT button.  
A confirmation box appears and select [Yes] to capture the 
projected image.
After capturing the projected image, go to the Logo select 
function and set it to “User”. Then the captured image will 
be displayed the next time you turn on the projector.
To cancel the Capture function, select [No].
Set the red frame pointer to the item and press the SELECT button.
Capture
Set the pointer (red arrow) to the item and press the SELECT button.
Select [Yes] to capture the projected image.
Select [Yes] to stop capturing.
Setting
HDMI setup
Select Normal or Enhanced according to the output signal 
of video equipment. Press the Point 7 8 buttons to switch 
between each option.
  Normal 
. . . .  When the output of video equipment is set to 
“STANDARD.”
  Enhanced
. .  When the output of video equipment is set to 
“ENHANCED.”
The names for the output setting of video equipment vary 
from equipment to equipment. For details, refer to the owner’s 
manual of video equipment.
When the black parts of the image are destroyed or stand out, 
please switch to "Normal" or "Enhanced", and then switch the 
output type of the HDMI video output equipment. 
HDMI setup
Press the Point 7 8 buttons to select Normal or Enhanced according to the output signal of video equipment. 
						

							
55

Change the Logo PIN code lock setting
After a correct Logo PIN code is entered, the following dialog box appears.
Use the Point 7 8 buttons to switch On/Off,
This function prevents an unauthorized person from changing 
the screen logo.
 Off
  . . . .  The screen logo can be changed freely from the 
Logo Menu.
  On
  . . . .  The screen logo cannot be changed without a 
Logo PIN code.
If you want to change the Logo PIN code lock setting, press 
the SELECT button and the Logo PIN code dialog box appears. 
Enter a Logo PIN code by following the steps below. The initial 
Logo PIN code is set to “4321” at the factory.
Logo PIN code lock
Enter a Logo PIN code
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit 
number. Press the Point d button to select “Logo PIN code 
change” and then press the SELECT button. The New Logo 
PIN code input dialog box appears. Set a new Logo PIN code.
Be sure to note the new Logo PIN code and keep it on hand. 
If you lost the number, you could no longer change the Logo 
PIN code setting. For details on PIN code setting, refer to “PIN 
code lock” on pages 58–59. Logo PIN Code Lock
Enter a Logo PIN code
Use the Point 7 8 buttons to switch On/Off, and then press 
the Point d button to move the pointer to “Quit.” Press the 
SELECT button to close the dialog box.
Change the Logo PIN code lock setting
CAUTION:
WHEN y
OU HAVE CHANGED THE LOGO PIN 
CODE,  WRITE DOWN  THE NEW PIN CODE 
IN COLUMN OF  THE LOGO PIN CODE NO .  
MEMO ON PAGE 88,  AND KEEP IT SECUREL y . 
SHOULD  THE LOGO PIN CODE BE LOST OR 
FORGOTTEN,  THE LOGO PIN CODE SETTING 
CAN NO LONGER BE CHANGED .
Change the Logo PIN code
Setting
Use the Point ed buttons on the side control or on 
the remote control to enter a number. Press the Point 
8 button to fix the number and move the red frame 
pointer to the next box. The number changes to “✳.” 
Repeat this step to complete entering a four-digit 
number. After entering the four-digit number, move the 
pointer to “Set.” Press the SELECT button so that you 
can change the Logo PIN code lock setting.
 If you fixed an incorrect number, use the Point 7 button 
to move the pointer to the number you want to correct, 
and then enter the correct number.
If you entered an incorrect Logo PIN code, “Logo 
PIN code” and the number (✳✳✳✳) will turn red for a 
moment. Enter the correct PIN code all over again. 
						

							
56

Choose the running speed of cooling fans from the following 
options.
 Normal  .......  Normal speed.
  Max  ...........  Faster than the normal speed.
Fan control
Setting
Filter control
You can replace the filter with this function. Press the SELECT 
button at Filter control to display a confirmation box. To replace, 
press the SELECT button at “YES” and the electrically operated 
filter starts to scroll.
You can also replace the filter by using the remote control 
(p.31). 
✔Note:
•  Filter replacement icon and “Please wait...” 
message appear on the screen when the filter is 
being scrolled.
•The filter cannot be rewound. 
• 
When  the  filter  is  replaced,  the  total  accumulated 
time of the filter use is automatically set to 0.
•   If the filter cartridge is not installed in the projector, 
'Filter control' is displayed in grayout.
RC sensor
Select a location of the infrared remote receiver of the remote 
control. See “Remote Control Receivers and Operating Range” 
on page 15 for details.
All . . . . . . . . . . .Activate all of the front, top and back receivers.
Front & Top . . . .Activate the front and top receivers. 
Top & Back . . . .Activate the top and back receivers. 
Front & Back . . .Activate the front and back receivers.
Front . . . . . . . . .Activate only the front receiver.
Top . . . . . . . . . .Activate only the top receiver.
Back . . . . . . . . .Activate only the back receiver.
Remote control
Remote control
When pressing the SELECT button at Remote control, the Remote control code menu appears.
The eight different remote control codes (Code 1–Code 8) are 
assigned to the projector; the factory-set, initial code (Code 1) 
and the other seven codes (Code 2 to Code 8). 
The same code should be set on both the projector and the 
remote control. For example, operating the projector in “Code 
7”, the remote control code also must be switched to “Code 7”.
 To change the code for the projector;
  Select a remote control code in this Setting Menu.
 To change the code for the remote control;
Check  the  Reset  Switch  to  "Use  position"  in  the  compartment 
lid on the back of the remote control.
And  then  while  holding  down  the  MENU  button,  press  and 
release  the  IMAGE  ADJ.  button  the  number  of  corresponding 
times  you  would  like  to  set  the  number  of  the  remote  control 
code for the projector. (See page 16)
To reset the code for the remote control;
Slide  the  Reset  Switch  to  "Reset  position"  in  the  compartment 
lid on back of the remote control. 
						

							
57

Power management
Time left before the lamp is off
Press the SELECT button at Power management and the dialog box appears. Use the Point 7 8 buttons to choose one of the three options.Press the Point d button to select the timer, and then use the Point 7 8 buttons to set the timer.
For reducing power consumption as well as maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not used for a certain 
period.
If the input signal is interrupted and no button is pressed for 
more than 30 seconds, the timer display with “No signal” 
appears. It starts the countdown until the lamp is turned off. The 
countdown time can be set between 1 and 30 minutes.
Use the Point 7 8 buttons to set the countdown timer.
Select one of the following options:
 Ready 
  . . . .  When the lamp has been fully cooled down, 
the POWER indicator starts blinking. In this 
condition, the projection lamp is turned on if the 
input signal is reconnected or any button on the 
side control or remote control is pressed . 
  Shutdown
. .  When the lamp has been fully cooled down, the 
power is turned off. 
  Off 
. . . . . . .  Power Management function is off. 
Power management
✔Note:
•Factory default is “Ready: 5 min.”
•  When the shutter is closed while the Power 
management function is working, the Power 
management function is released.
Setting
On start
When this function is set to “On,” the projector will be 
automatically turned on just by connecting the AC power cord to 
the wall outlet.
✔Note:
 •  Make sure that the MAIN ON / OFF switch is ON, other wise the On start function does not work.
 •  Be sure to turn off the projector properly (see “Turning Off the 
Projector” on page 25). If the projector is turned off in the incorrect sequence, the On start function does not work properly. 
						

							
58

Security
Key lock
Key lock
Security
Select Key lock and this box appears. Choose one of the alternatives with the Point ed buttons and select [Yes] to activate it.
This function locks the side control and remote control buttons 
to prevent operation by unauthorized persons.
. . . . . Unlocked.
. . . . .  Lock the side control buttons.
  To unlock, use the remote control.
. . . . . Lock the remote control buttons.  
To unlock, use the side control.
If the side control accidentally becomes locked and you 
do not have the remote control nearby and unable to 
operate the projector, contact the service center. 
PIN code lock
This function prevents the projector from being operated 
by unauthorized persons and provides the following setting 
options for security.
  Off
  . . . .  Unlocked.
  On1
  . . .  Enter the PIN code every time turning on the 
projector.
  On2
  . . .  Enter the PIN code to operate the projector once 
the Main On/Off Switch is pressed to Off or the 
power cord is unplugged ; as long as the AC power 
cord is connected and the Main On/Off Switch 
is pressed to ON, the projector can be operated 
without a PIN code.
Whenever you change the PIN code lock setting or the PIN 
code (the four-digit number), you are required to enter the PIN 
code. “1234” is set as the initial PIN code at the factory.
If you want to change the PIN code lock setting, press the 
SELECT button and the PIN code dialog box appears. Enter a 
PIN code by following the steps on the next page.
PIN code lock
When the projector is locked with a PIN code, the PIN code lock symbol appears on the menu bar. 
Set the red frame pointer to the item and press the SELECT button.
Setting 
						

							
59

Change the PIN Code 
Change the PIN code
CAUTION:
WHEN y OU HAVE CHANGED THE PIN CODE,  WRITE 
DOWN A NEW PIN CODE IN COLUMN OF  THE PIN CODE 
NO .  MEMO ON PAGE 88,  AND KEEP IT SECUREL y . IF 
y OU FORGET y OUR PIN CODE,  THE PROjECTOR CAN NO 
LONGER BE STARTED .The PIN code can be changed to your desired four-digit 
number. Press the Point d buttons to select “PIN code 
change” and press the SELECT button. The New PIN code 
input dialog box appears. Set a new PIN code.
Change the PIN Code Lock setting
Change the PIN code lock setting
Use the Point 7 8 buttons to switch between the options.
Enter a PIN code
Use the Point 7 8 button to select Off, On1, or On2 and then 
move the pointer to “Quit” with the Point d button. Press the 
SELECT button to close the dialog box.
After a correct Logo PIN code is entered, the following dialog box appears.
Enter a PIN code
Setting
Use the Point 7 8 buttons to adjust the Projector ID.
l Projector ID ... 1 - 999. (Factory default setting : Projector ID 1)
This feature allows users to set serial communication 
configuration (Projector ID) when several projectors are 
connected via the RS-232C terminal (serial port) of the 
projector.
Projector ID 
Use the Point ed buttons on the side control or on 
the remote control to enter a number. Press the Point 
8 button to fix the number and move the red frame 
pointer to the next box. The number changes to “✳.” 
Repeat this step to complete entering a four-digit 
number. After entering the four-digit number, move 
the pointer to “Set.” Press the SELECT button so that 
you can change the PIN code lock setting .
 If you fixed an incorrect number, use the Point 7 
button to move the pointer to the number you want 
to correct, and then enter the correct number.
If you entered an incorrect PIN code, “PIN code” and 
the number (✳✳✳✳) will turn red for a moment. Enter 
the correct PIN code all over again. 
						

							
60

Setting
Shutter
Shutter function is available to block out light to the 
screen, so that the screen can be used for the other 
presenters.
Prohibits the shutter operation from the remote control and 
the projector's side control.
Remote control 
 . . .  Selecting "On" prohibits the shutter 
operation from the remote control.
Projector . . . . . . . .  
Selecting "On" prohibits the shutter 
operation from the side control.
It is possible to prohibit the shutter operation from both of the 
remote control and the side control.
Protection
Management
The Shutter Management function turns off the projection 
lamp when the projector is left with the shutter closed and 
the set time has passed away. The count-down time can be 
set between 5 and 480 minutes. When the count-down time 
has elapsed, the shutter will be opened up automatically and 
the lamp will be turned off to cool itself down. The SHUTTER 
indicator is blinking blue during this cooling-off period. When 
the lamp has been fully cooled down, the POWER indicator 
turns green lighting and the SHUTTER indicator keeps 
blinking. Should the ON / STAND-BY button be pressed in 
this condition, the projection lamp will be turned on and the 
SHUTTER indicator turns off.
✔Note:
• The Factory default value is set to 180 
minutes for the count down time.
•  The Shutter Management function cannot be 
halted.
Shutter
Set the red frame pointer to the item and press the SELECT button.
Effect
Choose the image effect at opening or closing the shutter 
from the following options.
  On  .............  The Image will fade in and out at opening or 
closing the shutter.
  Off  .............  Disable.
 
Release key
Choose the active buttons to release the shutter when the 
shutter is closed from the following options.
  Any  ............  By pressing any buttons on the remoter control 
and the side control when the shutter is closed, 
the shutter will be released.
  SHUTTER  ..   Only the SHUTTER button on the remote 
control and the side control can be released the 
shutter when the shutter is closed. 
Only the following buttons are active when the 
shutter is closed; 
- INPUT button and INPUT 1/2/3/4 button 
- ON/STAND-BY button