Home > Sanyo > Projector > Sanyo LNS W03 Installation Manual

Sanyo LNS W03 Installation Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Sanyo LNS W03 Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Type of the Cabinet (1) See Page 2
    LCD PROJECTOR LENS
    MODEL NO. LNS-W03
    LENS REPLACEMENT 
    AND INSTALLATION PROCEDURES
    NOTES ON REPLACEMENT AND INSTALLATION
    The procedures and the needed pars for lens installation depend on the type of
    cabinet.  Before installing or replacing the lens, make sure the type of cabinet and be
    sure to refer to the Installations corresponding with your projector.
    When installing or replacing the lens, make sure the Lens Model No. matches with
    your projector.  Refer to the catalog, or contact your sales dealer for the proper Lens
    Model No.
    TYPE OF THE CABINET AND  INSTALLATION PROCEDURES
    Refer to the Installation procedure corresponding to your projector and install the lens
    correctly. (See the chart below.)
    Type of the Cabinet (2) See Page 4
    1AA6P1P2952--  (ICYZ)
    ÞFor use the other models (other than above cabinet), contact your sales dealer. 
    						
    							Some parts are not used for installation or replacement.  Keep these parts for later use.
    Note : Figures in this manual may be differ from the actual product.
    NOTES ON LENS INSTALLATION
    The ZOOM, FOCUS and LENS SHIFT adjustment on the Top Control or the
    Remote Control cannot be operated with this Lens.
    • Lens installation and replacement should be made by the qualified service per-
    sonnel.
    • Be sure to install the lens following this procedure precisely.
    • The lens cover is on the lens for protection.  Be sure to replace the lens cover
    before installation.
    • When installing or replacing the lens, be careful not to stain, scratch or damage
    the lens.
    After installing or replacing the lens, be sure to check the following for safety.
    1. Check the lens is securely fixed by 4 screws.
    2. Check no part is missing, or no mounting part is loose.
    BE SURE TO CHECK FOR SAFETY
    LIST OF CONTENTS
    Following parts are included in the packing.
    • LENS 1 pc.
    • DRIVER 1 pc.
    • LIGHT-BLOCK SHEET 2 pcs. 
    -1-
    Type FE1 (Part No. 610 280 2634) For use the Type (1) Cabinet
    Type FB1 (Part No. 610 285 8211) For use the Type (2) Cabinet 
    						
    							LENS REPLACEMENT AND INSTALLATION PROCEDURE
    1. Remove screws A (2 screws).
    2. Pull down the lower lens cover while pushing
    the part D, then remove it.
    3. Remove screws B (2 screws).
    4. Remove screws C (2 screws) and remove
    upper lens cover.
    1
    A
    Fig-1
    Fig-2
    IN CASE OF MODEL WITHOUT LENS
    Remove 2 screws and pull down the plate.
    2
    UPPER LENS COVER
    LOWER LENS COVER
    C
    B
    D
    D
    COVER PLATE
    REMOVE THE LENS COVER. (See figure-1)
    (At the step , insert the light-block sheet in
    the same position as the removed cover plate
    has been placed. Two screws are not used.)4
    REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)
    LENS 
    MOTOR LEAD
    CONNECTORS  K16A and  K16B
    (D)
    (D)(D)
    (D)
    B
    A
    LENS MOTOR
    Fig-3
    ❋Figure shown inside of the cabinet.REMOVE THE LENS. (See figure-3.)
    1. Disconnect the Lens Shift connector
    “K16A” from circuit board.
    2. Disconnect the Zoom and Focus con-
    nector “K16B” from circuit board.
    3. Loosen the A, B wire holder and
    remove the lens motor lead.
    4. Remove screws D (4 screws) which
    fastens the lens and remove the lens.
    IN CASE OF MODEL WITH LENS
    A
    Perform the steps  to  for lens replacement and installation.51
    SCREWS
    First set the lens at the center position with lens
    shift adjustment.
    (Type 1 Cabinet)
    Disconnect the Lens Shift connector
    (K16A) from circuit board. (See Fig. 3.)
    -2- 
    						
    							MOUNT THE LENS COVER. (See figure-6)
    INSTALL THE LENS. (See figure-4)
    1. Remove protective caps(front and
    back) on the lens.
    2. Mount the lens on mounting bracket
    of the main cabinet with 4 screws.
    Use the screws included with the lens.
    Use the driver included with the lens to
    fasten the screws.
    (After using, keep it for latter use.)
    3
    A
    INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)4
    Install the light-block sheet around the lens
    as shown in the illustration.  Use the sheet
    included with the lens.
    Make sure the part no. and mark (TOP and
    BACK) on Light-Block Sheet and set them
    properly.
    1. Insert the upper part lens cover and fix
    them with screws A (4 screws).
    2. Insert the lower part lens cover and fix
    them with screws B. (2 screws).
    5
    LENS MOUNTING BRACKET
    ATTACHED DRIVER
    UPPER LENS COVER
    LOWER LENS COVER
    A
    B
    Fig-4
    Fig-5
    Fig-6
    When in install the both upper and lower
    lens covers, install the light-block sheet so
    that it  should be placed in the guide slot.
    (place of the cover plate had been placed.
    See figure-2.) If the installation of light-block
    sheet is incorrect, it will be the cause of
    leakage of light or the dust entering at the
    main cabinet.
    LIGHT-BLOCK SHEET
    Type FE1
    (Part No. 610 280 2634)
    -3-
    ADJUST FOCUS
    Adjust focus following Focus Adjustment on
    page 6.  
    						
    							1. Remove screws A (2 screws).
    2. Push part B and pull Upper Lens Cover up.
    1
    Fig-1
    Fig-2
    2
    REMOVE THE UPPER LENS COVER. (See figure-1)
    (At the step , insert the light-block sheet in
    the same position as the removed cover plate
    has been placed. Two screws are not used.)6
    Perform the steps  to  for lens replacement and installation.71
    First set the lens at the center position with lens shift adjustment.
    UPPER LENS
    COVER 
    A
    LOWER LENS
    COVER 
    C
    COVER PLATE
    UPPER LENS
    COVER 
    D
    C B
    Fig-3
    1. Remove screws C (4 screws).
    2. Pull Lower Lens Cover toward front and
    remove.
    REMOVE THE LOWER LENS COVER. (See figure-2)
    3
    1. Remove screws D (2 screws) and Cover
    Plate on the back of Upper Lens Cover.
    REMOVE THE COVER PLATE. (See figure-3)
    LENS REPLACEMENT AND INSTALLATION PROCEDURE(Type 2 Cabinet)
    -4- 
    						
    							INSTALL THE LENS. (See figure-5)
    1. Remove protective caps(front and
    back) on the lens.
    2. Mount the lens on mounting bracket
    of the main cabinet with 4 screws.
    Use the screws included with the lens.
    Use the driver included with the lens to
    fasten the screws.
    (After using, keep it for latter use.)
    5
    INSTALL THE LIGHT-BLOCK SHEET. (See figure-6)6
    Install the light-block sheet around the lens
    as shown in the illustration.  Use the sheet
    included with the lens.
    Make sure the part no. and mark (TOP and
    BACK) on Light-Block Sheet and set them
    properly.
    LENS MOUNTING BRACKET
    ATTACHED DRIVER
    Fig-5
    Fig-6LIGHT-BLOCK SHEET
    Type FB1
    (Part No. 610 285 8211)
    LEAD
    HOLDER
    CONNECTOR
    K96S
    Fig-4
    DISCONNECT THE LENS SHIFT CONNECTORS. (See figure-4)
    Disconnect the Lens Shift Connectors
    (K96S and K96R) from circuit board.
    4
    CONNECTOR
    K96R
    -5-
    ADJUST FOCUS
    Adjust focus following Focus Adjustment on
    page 6.  
    						
    							FOCUS ADJUSTMENT
    Set up the projector and project image on the screen.
    1. Loosen the Focus Lock Screw on the projection
    lens.
    2. Rotate the projection lens to obtain proper focus
    on center area of the screen. 
    When the distance of the screen and lens is 1 meter,
    set 
    Ômark (yellow) of the lens on Focus Lock Screw
    position. 
    3. Lock the Focus Lock Screw securely.
    When proper focus is not observed at outer area of
    the screen, proceed following adjustments.
    4. Loosen the Focus Lock Ring on the projection
    lens. (Turn the Lock Ring to counter-clockwise.)
    5. Rotate the lens to obtain proper focus on outer
    area of the screen.
    6. Lock the Focus Lock Ring securely.  (Turn the Lock
    Ring to clockwise.)
    If proper focus is not observed entire screen, repeat
    above adjustment 1~ 6.
    Focus Lock Screw
    Focus Lock Ring
    LOWER LENS
    COVER 
    UPPER LENS
    COVER 
    LIGHT-BLOCK
    SHEET
    FLAPSlide into front
    of the flap.
    Slide into front
    of the flap.
    FLAP
    Slide upper both side of LIGHT BLOCK
    Sheet into between  and 
    .
    21
    CABINET
    GUIDE
    1
    2
    MOUNT THE LENS COVER. (See figure-7)7
    1. Replace Lower Lens Cover. Slide Light-Block Sheet into the guide of Lower Lens Cover
    and set them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover with 4 Screws C.
    (See Fig. 2.)
    2. Replace Upper Lens Cover. Slide Light-Block Sheet into the guide of Upper Lens Cover
    and set them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover with 2 Screws A.
    (See Fig. 1.)
    Fig-7
    Ômark (yellow)
    -6- 
    						
    							©ßÏÉ¿Äw	Ý 	
    Ö”´€	°
    1AA6P1P2952--  (ICYZ)
    ÷	¥Óé´£«»”èï¶
    
    
    						
    							èï¶w	“
    ÇZz‡hx¦õwKqtzS–Mts’sM
    æ
    ¼U’”	ÔùUK“‡b{
    \•’w
    æ
    ¼x™Ô
    žAqs”	ÔùUK“‡bwpzG
    ~t-`oXi^M{
    Þ
    †Ì¤w
    $xîMw‹wqŸs”	ÔùUK“‡b{
    	“
    ÇZ^À	Íw«™
    \wèï¶xzæÞ¯ï‡hx÷	¥Óé´£«»”Š.pw¶”ÜzÑ¥”§µ
    S‘|èﶳÑÄÐ
    TxpV‡dœ{
    Ô èï¶w	“
    ÇZz¦õ^Àx±”ϵU	[»UæloXi^M{
    Ô èï¶w	“
    ÇZz¦õ^Àx\w^À		q	{t`hUMz
    Y`XæloXi
    ^M{
    Ô èï¶txèï¶-¢whŠw©ß¿ÓU
    ÇMoM‡b{èﶛ	“
    ÇZ”
    ‡QtzTs’c©ß¿Ó›xc`oXi^M{
    Ô èï¶w	“
    ÇZz	“Ž`wqVzèï¶w
    ¯Ø›	p^˜lh“	‡›
    ÇZ
    h“`sM‘O]«™Xi^M{
    èﶛ	“
    ÇZhKqzèﶧ̔›	“
    ÇZ”‡QtzmWw:U›ælo
    Xi^M{
     
    						
    All Sanyo manuals Comments (0)

    Related Manuals for Sanyo LNS W03 Installation Manual