Home > Sanyo > Projector > Sanyo LNS-T01, LNS- W01 Installation Manual

Sanyo LNS-T01, LNS- W01 Installation Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Sanyo LNS-T01, LNS- W01 Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							PARTS LIST
    Following parts are contained in the packing.
    ·  LENS                
    · LENS MOUNTING SCREWS     
    · DRIVER                                    
    · LIGHT-BLOCK SHEET               
    NOTES ON LENS INSTALLATION
    LCD PROJECTOR LENS
    MODEL NO. LNS-W01
    LNS-T01
    Lens installation should be performed by the qualified service personnel.
    It should be followed by this procedure precisely.
    Before attempt to install the lens, confirm the model number (both the LCD
    projector and the lens) and use the proper lens.
    If you have any questions, contact to the dealers.
    Following checks and confirmations should be taken for safety.
    Check the following things by the time of the cabinet assembly after the
    lens installation.
    1. Confirm the lens is securely fixed by 4 screws.
    2. Wiring must not be tangled in the mechanical part.
    3. There is no missing part, or no loosing mounting part.
    1AA6P1P1979-- (ICPW)
    1 piece
    6 screws (2 for spare)
    1 piece
    1 sheet l The focus and zoom of this lens can’t be adjusted by controls on main cabinet or the remote control unit.
    LENS REPLACEMENT AND
    INSTALLATION PROCEDURE 
    						
    							LENS REPLACEMENT AND INSTALLATION PROCEDURE
    Remove screws A (2 screws).
    Pull down the lower lens cover while pushing
    the part D, then remove it.
    Remove screws B (2 screws).
    Remove screws C (2 screws) and remove
    upper lens cover.1
    5Perform the steps  to for lens replacement and installation.
    1
    1.
    2.
    A
    Fig-1
    Fig-2
    lIN CASE OF MODEL WITHOUT LENS
    Remove 2 screws and pull down the plate.
    2
    3.
    4.
    UPPER LENS COVER
    LOWER LENS COVER
    C
    B
    D
    D
    COVER PLATE
    REMOVE THE LENS COVER. (See figure-1)
    (At the step , insert the light-block sheet in
    the same position as the removed cover plate
    has been placed. Two screws are not used.)
    4
    REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)
    LENS 
    MOTOR LEAD
    CONNECTOR “ K16B”
    (D)
    (D)(D)
    (D)
    B
    A
    LENS MOTOR
    Fig-3
    kFigure shown inside of the cabinet.
    REMOVE THE LENS. (See figure-3.)
    1. Remove the connector “K16B” of the
    circuit board.
    2. Loosen the A, B wire holder and
    remove the lens motor lead.
    3. Remove screws D (4 screws) which
    fastens the lens and remove the lens.
    lIN CASE OF MODEL WITH LENS
    A
    Set the light-block
    sheet, so that the
    large rounder side
    is set over the lens. 
    						
    							MOUNT THE LENS COVER. (See figure-6)
    INSTALL THE LENS. (See figure-4)
    Remove protective caps(front and
    back) on the lens.
    Mount the lens on mounting bracket of
    the main cabinet with 4 screws.
    Use the screws included with the lens.
    Use the driver included with the lens
    to fasten the screws.
    3
    1.
    2.
    A
    INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)
    When this projector permanently install in the
    structure, slide the picture, obtain correct
    focus, then lock the lens by Focus Lens Lock
    screw at this step.
    4
    Install the light-block sheet around the lens as shown in the illustration.
    Use the sheet included with the lens.
    Insert the upper part lens cover and
    fix them with screws A (4 screws).
    Insert the lower part lens cover and
    fix them with screws B. (2 screws).
    5
    1.
    2.
    LENS MOUNTING BRACKET
    ATTACHED DRIVER
    FOCUS LENS LOCK SCREW
    UPPER LENS COVER
    LOWER LENS COVER
    A
    B
    Fig-4
    Fig-5
    Fig-6
    (After using, save it for latter use.)
    When in install the both upper and lower lens
    covers, install the light-block sheet so that it
    should be placed in the guide slot. (the place
    the covers had been placed. See figure-2.). If
    the installation of light-block sheet is incor-
    rect, it will be the cause of leakage of light or
    the dust entering at the main cabinet.
    LIGHT-BLOCK SHEET
    Adjust focus by rotating
    the lens. 
    						
    All Sanyo manuals Comments (0)

    Related Manuals for Sanyo LNS-T01, LNS- W01 Installation Manual