Home > Sanyo > Projector > Sanyo LNS-S02 Installation Manual

Sanyo LNS-S02 Installation Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Sanyo LNS-S02 Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							PARTS LIST
    Following parts are contained in the packing.
    ·  LENS                
    · LENS MOUNTING SCREWS     
    · DRIVER                                    
    · LIGHT-BLOCK SHEET               
    NOTES ON LENS INSTALLATION
    LENS REPLACEMENT AND
    INSTALLATION PROCEDURE
    LCD PROJECTOR LENS
    MODEL NO. LNS-S02
    Lens installation should be performed by the qualified service personnel.
    It should be followed by this procedure precisely.
    Before attempt to install the lens, confirm the model number (both the LCD
    projector and the lens) and use the proper lens.
    If you have any questions, contact to the dealers.
    Following checks and confirmations should be taken for safety.
    Check the following things by the time of the cabinet assembly after the
    lens installation.
    1. Confirm the lens is securely fixed by 4 screws.
    2. Wiring must not be tangled in the gear of the lens motor or the other 
    mechanical part.
    3. There is no missing part, or no loosing mounting part.
    1AA6P1P1981-- (ICPE)
    1 piece
    6 screws (2 for spare)
    1 piece
    1 sheet 
    						
    							LENS REPLACEMENT AND INSTALLATION PROCEDURE
    Remove screws A (2 screws).
    Pull down the lower lens cover while pushing
    the part D, then remove it.
    Remove screws B (2 screws).
    Remove screws C (2 screws) and remove
    upper lens cover.1
    5Perform the steps tofor lens replacement and installation.
    1
    1.
    2.
    A
    Fig-1
    Fig-2
    Remove 2 screws and pull down the plate.
    2
    3.
    4.
    UPPER LENS COVER
    LOWER LENS COVER
    C
    B
    D
    D
    COVER PLATE
    REMOVE THE LENS COVER. (See figure-1)
    (At the step , insert the light-block sheet in
    the same position as the removed cover plate
    has been placed. Two screws are not used.)
    4
    REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)
    INSTALL THE LENS. (See figure-3)
    Remove protective caps(front and
    back) on the lens.
    Mount the lens on mounting brack-
    et of the main cabinet with 4
    screws.Use the screws included
    with the lens.
    Use the driver included with the
    lens to fasten the screws.
    (After using, save it for latter use.)
    Connect the lead connector of the
    lens motor to the “K16B” on the
    circuit board as shown in figure-4.
    Fasten the lens motor lead at the
    A, B points with wire holder as
    shown in figure-4.3
    1.
    2.
    LENS MOUNTING BRACKET
    ATTACHED DRIVERFig-3
    3.
    4.
    LENS MOTOR 
    						
    							MOUNT THE LENS COVER. (See figure-6)
    A
    INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)
    Install the light-block sheet around the lens as
    shown in the illustration.
    (Use the sheet included with the lens.)
    Set the light-block sheet, so that the large rounder
    side is set over the lens.4
    Insert the upper part lens cover and
    fix them with screws A (4 screws).
    Insert the lower part lens cover and
    fix them with screws B. (2 screws).
    5
    1.
    2.
    UPPER LENS COVER
    LOWER LENS COVER
    A
    B
    Fig-5
    Fig-6
    When in install the both upper and lower lens
    covers, install the light-block sheet so that it
    should be placed in the guide slot of the lens
    cover. If the installation of the light-block
    sheet is incorrect, there will be the space
    between lens and the lens cover, so that it will
    be the cause of leakage of light or the dust
    entering at the main cabinet.
    LIGHT-BLOCK SHEET
    Set the light-block sheet, so that the
    large rounder side is set over the lens.
    LENS MOTOR LEAD
    CONNECTOR “ K16B”
    (D)
    (D)(D)
    (D)
    B
    LENS MOTOR
    Fig-4
    kFigure shown inside of the cabinet.
    A
    WIRE HOLDER 
    						
    All Sanyo manuals Comments (1)

    Related Manuals for Sanyo LNS-S02 Installation Manual