Home > Sanyo > Projector > Sanyo LNS-M01, LNS-S01 Installation Manual

Sanyo LNS-M01, LNS-S01 Installation Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Sanyo LNS-M01, LNS-S01 Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							PARTS LIST
    Following parts are contained in the packing.
    ·  LENS                
    · LENS MOUNTING SCREWS     
    · DRIVER                                    
    · LIGHT-BLOCK SHEET               
    NOTES ON LENS INSTALLATION
    LCD PROJECTOR LENS
    MODEL NO. LNS-M01
    LNS-S01
    Lens installation should be performed by the qualified service personnel.
    It should be followed by this procedure precisely.
    Before attempt to install the lens, confirm the model number (both the LCD
    projector and the lens) and use the proper lens.
    If you have any questions, contact to the dealers.
    Following checks and confirmations should be taken for safety.
    Check the following things by the time of the cabinet assembly after the
    lens installation.
    1. Confirm the lens is securely fixed by 4 screws.
    2. Wiring must not be tangled in the gear of the lens motor or the other 
    mechanical part.
    3. There is no missing part, or no loosing mounting part.
    1AA6P1P1980-- (ICPP)
    1 piece
    6 screws (2 for spare)
    1 piece
    1 sheet
    LENS REPLACEMENT AND
    INSTALLATION PROCEDURE 
    						
    							LENS REPLACEMENT AND INSTALLATION PROCEDURE
    Remove screws A (2 screws).
    Pull down the lower lens cover while pushing
    the part D, then remove it.
    Remove screws B (2 screws).
    Remove screws C (2 screws) and remove
    upper lens cover.1
    4Perform the steps  to for lens replacement and installation.
    1
    1.
    2.
    A
    Fig-1
    Fig-2
    lIN CASE OF MODEL WITHOUT LENS
    Remove 2 screws and pull down the plate.
    2
    3.
    4.
    UPPER LENS COVER
    LOWER LENS COVER
    C
    B
    D
    D
    COVER PLATE
    REMOVE THE LENS COVER. (See figure-1)
    (At the step , insert the light-block sheet in the same
    position as the removed cover plate has been placed.
    Two screws are not used.)
    Use the light-block sheet included with lens.
    Set the light-block sheet, so that the large rounder side
    is set over the lens.
    4
    REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)
    LENS MOTOR LEAD
    CONNECTOR “ K16B”
    (D)
    (D)(D)
    (D)
    B
    LENS MOTOR
    Fig-3
    kFigure shown inside of the cabinet.
    REMOVE THE LENS. (See figure-3.)
    1. Remove the connector “K16B” of the
    circuit board.
    2. Loosen the A, B wire holder and
    remove the lens motor lead.
    3. Remove screws D (4 screws) which
    fastens the lens and remove the lens.
    lIN CASE OF MODEL WITH LENS
    A
    Set the light-block
    sheet, so that the
    large rounder side
    is set over the lens.
    SCREWS
    WIRE HOLDER 
    						
    							INSTALL THE LENS. (See figure-4,5.)3
    1. Mount the lens at the lens
    mounting bracket with screws
    (4 screws) included with the
    lens. Use the driver included
    with the lens to fasten the
    screws . (After using, save it for
    latter use.)
    2. Connect the lens motor lead to
    the connector “K16B” of the cir-
    cuit board.
    3. Fasten the lens motor lead at
    the A, B points with wire holder.
    LENS 
    MOTOR LEAD
    CONNECTOR “ K16B “
    (D)
    (D)(D)
    (D)
    B
    LENS MOTOR
    Fig-5
    This part wiring should
    not be tightened. kFigure shown inside of the cabinet.
    LIGHT-BLOCK SHEET
    Fig-4
    LENS MOUNTING BRACKET
    WIRE HOLDER
    ATTACHED DRIVER
    MOUNT THE LENS COVER. (See figure-1)4
    When in install the both upper and lower lens covers,
    put the light-block sheet through the lens and install
    the sheet so that it  should be placed in the guide slot
    of the lens cover. If the installation of the light-block
    sheet is incorrect, there will be the space between
    lens and the lens cover, so that it will be the cause of
    leakage of light or the dust entering at the main cab-
    inet.
    A 
    						
    							†
    ¶whŠz
    žcmWw:Uq¬Ý›æloXi^M{
    èï¶	“
    ÇZwKqzèﶧ̔›	“
    ÇZ”‡QtzmWw:U›
    æloXi^M{
     
    						
    							èï¶w¦õ~	“
    ÇZx
    µ«æᔢŠ£›Ž`‡b{
    èﶧ̔
    						
    							èï¶Þ”»”
    èï¶Þ”»”æ”Å
    
    $
    
    ¢£
    	“
    ÇZwqV\w
    æ
    ü
    t(›Ëhd”{
    
    $
    
    ÇÅå Ì”
    èï¶Ú¢ïÄÒå­¿Äèﶛ	“
    ÇZ‡b{¢
    $
    €	°£
     
    						
    All Sanyo manuals Comments (0)

    Related Manuals for Sanyo LNS-M01, LNS-S01 Installation Manual