Samsung Ud46e-p Manual
Have a look at the manual Samsung Ud46e-p Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 Before Installing the Product (Installation Guide)To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. •Ensure that an authorized installation company installs the wall mount. •Otherwise, it may fall and cause personal injury. •Make sure to install the specified wall mount. Switching between portrait and landscape ― Contact Samsung Customer Service Centre for further details. • To use the product in portrait orientation, rotate it clockwise. A B Figure 1.1 Side view Ventilation Installation on a Perpendicular Wall A Minimum 40 mm B Ambient temperature: Under 35 C • When installing the product on a perpendicular wall, allow at least 40 mm of space between the product and wall surface for ventilation and ensure that the ambient A temperature is kept below 35 C.
22 A B C E Figure 1.3 Side view D D Figure 1.2 Side view Installation on an Indented Wall ― Contact Samsung Customer Service Centre for further details. Plane view A Minimum 40 mm B Minimum 70 mm C Minimum 50 mm D Minimum 50 mm E Ambient temperature: Under 35 C ―When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C. Dimensions 1 2 3 4 5 Unit: mm (inches) Model name12234345 UD46E-P 1022.1 (40.2)1018.3 (40.1)572.9 (22.6)576.6 (22.7)97.4 (3.8) UD55E-P / UD55E-S 1213.5 (47.8)1209.8 (47.6)680.6 (26.8)684.3 (26.9)96.6 (3.8) ― All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. Refer to the dimensions prior to performing installation of your product. Not responsible for typographical or printed errors.
23 Installing the Wall Mount 1 Preparing before installing Wall-Mount To install a wall-mount from another manufacturer, use the Holder-Ring(). Installing the Wall Mount The wall mount kit (sold separately) allows you to mount the product on the wall. For detailed information on installing the wall mount, see the instructions provided with the wall mount. We recommend you contact a technician for assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
24 Wall Mount Kit Specifications (VESA) ―Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to surfaces other than plaster board, please contact your nearest dealer for additional information. If you install the product on a slanted wall, it may fall and result in severe personal injury. • Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided. •Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product. •For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications. • Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents. •Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions. •Do not mount the product at more than a 15 degree tilt. •Always have two people mount the product on a wall. •Standard dimensions for wall mount kits are shown in the table below. Unit: mm (inches) Model name VESA screw hole specs (A * B) in millimetersStandard Screw Quantity UD46E-P / UD55E-P / UD55E-S 600 × 400 (23.6 × 15.7)M8 / L14 ~ 164 ― Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
25 Remote Control (RS232C) Cable Connection RS232C Cable InterfaceRS232C (9 pins) PinTxD (No.2), RxD (No.3), GND (No.5) Bit rate9600 bps Data bits8 bit ParityNone Stop bit1 bit Flow controlNone Maximum length15 m (only shielded type) •Pin assignment 12 3 4 5 6 7 8 9 Pin Signal 1Detect data carrier 2Received data 3Transmitted data 4Prepare data terminal 5Signal ground 6Prepare data set 7Send request 8Clear to send 9Ring indicator
26 •RS232C cable Connector: 9-Pin D-Sub Cable : Cross Cable 1 59 6-P1-6 95 1-P2- -P1- -P1- -P2--P2- Female Rx Tx Gnd2 3 5 -------->
27 •Connector : RJ45 Direct LAN cable (PC to HUB) RJ45 RJ45 MDC HUB P1 P1 P2 P2 SignalP1P2Signal TX+11TX+ TX-22TX- RX+33RX+ RX-66RX- Cross LAN cable (PC to PC) RJ45P1 P2 SignalP1P2Signal TX+13RX+ TX-26RX- RX+31TX+ RX-62TX-
28 Connection •Connection 1 RS232CIN OUTRS232CINOUTRS232CINOUTRS232CINOUT • Connection 2 RJ45RJ45 • Connection 3 RJ45RS232CIN OUTRS232CINOUTRS232CINOUTRS232C OUT
29 Control Codes Viewing control state (Get control command) HeaderCommand IDData length Checksum 0xAA Command type 0 Controlling (Set control command) HeaderCommand IDData length DataChecksum 0xAA Command type 1Value Command No.Command type CommandValue range 1Power control 0x110~1 2Volume control 0x120~100 3Input source control 0x14- 4Screen mode control 0x18- 5Screen size control 0x190~255 6PIP on/off control 0x3C0~1 7Auto adjustment control (PC and BNC only) 0x3D 0 8Video wall mode control 0x5C0~1 9Safety Lock 0x5D0~1 No.Command type CommandValue range 10Video Wall On 0x840~1 11Video Wall User Control 0x89- • All communications take place in hexadecimals. The checksum is calculated by adding up all values except the header. If a checksum adds up to be more than 2 digits as shown below (11+FF+01+01=112), the first digit is removed. E.g. Power On & ID=0 Header Command IDData length Data 1Checksum 0xAA 0x11 1"Power" HeaderCommand IDData length Data 112 0xAA 0x11 11 • To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID as "0xFE" and transmit commands. Commands will be executed by each device but ACK will not respond.
30 Power control •Function A product can be powered on and off using a PC. •Viewing power state (Get Power ON / OFF Status) Header Command IDData length Checksum 0xAA 0x11 0 • Setting power ON/Off (Set Power ON / OFF) Header Command IDData length DataChecksum 0xAA 0x11 1"Power" "Power": Power code to be set on a product. 1: Power ON 0: Power OFF • Ack Header Command IDData length Ack/Nakr-CMDVal1Checksum 0xAA 0xFF 3'A'0x11"Power" "Power": Power code to be set on a product. • Nak Header Command IDData length Ack/Nakr-CMDVal1Checksum 0xAA 0xFF 3'N'0x11"ERR" "ERR" : A code showing what error has occurred. Volume control • Function The volume of a product can be adjusted using a PC. •Viewing volume state (Get Volume Status) Header Command IDData length Checksum 0xAA 0x12 0 • Setting the volume (Set Volume) Header Command IDData length DataChecksum 0xAA 0x12 1"Volume" "Volume": Volume value code to be set on a product. (0-100) • Ack Header Command IDData length Ack/Nakr-CMDVal1 Checksum 0xAA 0xFF 3'A'0x12"Volume" "Volume": Volume value code to be set on a product. (0-100) • Nak Header Command IDData length Ack/Nakr-CMDVal1Checksum 0xAA 0xFF 3'N'0x12"ERR" "ERR" : A code showing what error has occurred.