Samsung Ud46e-p Manual

							161
Other issue
The product smells like plastic.The plastic smell is normal and disappears over time.
The monitor appears tilted.Remove and then attach the stand again to the product.
Audio or video cuts out intermittently.Check the cable connection and connect it again if required.
Using a very hard or thick cable may corrupt audio and video files.
Make sure cables are flexible enough to ensure durability. When mounting the product onto a wall, it 
is recommended to use right-angle cables.
Small particles are found on the edges of the product.The particles are part of the product design. The product is not defective.
The PIP menu is not available.The menu is enabled or disabled depending on the Source  mode.
When I try to change the PC resolution, a message "Th e 
defined  resolution  is not  supported ." appears.The message "The defined resolution is not supported." appears if the input source resolution 
exceeds the maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
There is no sound from the speakers in HDMI mode when a 
DVI-HDMI cable is connected.DVI cables do not transmit sound data.
Make sure to connect the audio cable to the correct input jack to enable audio.
HDMI  Black  Le vel  is not functioning properly on an HDMI 
device with YCbCr output.This function is available only when a source device, such as a DVD player and STB, is connected to the 
product via an HDMI (RGB signal) cable.
There is no sound in HDMI mode.Displayed picture colours may not look normal. Video or sound may not be available. This can occur if 
a source device that only supports an older version of the HDMI standard is connected to the product.
If these issues occur, connect an audio cable along with the HDMI cable.
Some PC graphics cards may not automatically recognize HDMI signals that do not include sound. In 
this case, manually select a sound input.
Sound input Screen mode
PC AutoPC settings
DVI PC Audio In (Stereo 
ports) PC settings  
						

							162
Other issue
The IR sensor is not functioning.Make sure the sensor light turns on when a button is pressed on the remote control.
 •If the sensor light does not turn on, turn the power switch off and then on again on the back of 
the product.
If the sensor light still does not turn on after the power switch is turned off and then on again, an 
internal jack may be disconnected.
Contact your nearest service centre to have the product serviced.
In power-saving mode, when the input source is  Display Po rt , 
PC display settings cannot be saved. • Go to System  
→  General and set Max. Power Saving to Off. Alternatively, configure the PC 
display output settings again. Ensure the set is turned on.
When booting the PC with the input source set to 
D isplayP ort , the BIOS and booting screens do not appear. •
Boot the PC when the set is turned on or when the input source is not  DisplayPort.  
						

							163
Q & A
QuestionAnswer
How can I change the frequency?Set the frequency on your graphics card.
 •
Windows XP: Go to Control Panel  → Appearance and Themes 
→ Display 
→ Settings 
→ 
Advanced  → Monitor and adjust the frequency in Monitor Settings.
 •
Windows ME/2000: Go to Control Panel  → Display 
→ Settings 
→ Advanced 
→ Monitor and 
adjust the frequency in Monitor Settings.
 • Windows Vista: Go to Control Panel  → Appearance and Personalization 
→ Personalize 
→ 
Display Settings  → Advanced Settings 
→ Monitor and adjust the frequency in  
Monitor Settings.
 • Windows 7: Go to Control Panel  → Appearance and Personalization 
→ Display 
→  
Adjust resolution  → Advanced Settings 
→ Monitor and adjust the frequency in  
Monitor Settings.
 • Windows 8: Go to Settings  → Control Panel 
→ Appearance and Personalization 
→  
Display  → Adjust resolution 
→ Advanced Settings 
→ Monitor and adjust the frequency in 
Monitor Settings.
How can I change the resolution? • Windows XP: Go to Control Panel  → Appearance and Themes 
→ Display 
→ Settings and 
adjust the resolution.
 • Windows ME/2000: Go to Control Panel  → Display 
→ Settings and adjust the resolution.
 •
Windows Vista: Go to Control Panel  → Appearance and Personalization 
→ Personalize 
→ 
Display Settings and adjust the resolution.
 • Windows 7: Go to Control Panel  → Appearance and Personalization 
→ Display 
→  
Adjust Resolution and adjust the resolution.
 • Windows 8: Go to Settings  → Control Panel 
→ Appearance and Personalization 
→  
Display  → Adjust Resolution and adjust the resolution.
 -
Refer to the user manual for your PC or 
graphics card for further instructions on 
adjustment.  
						

							164
QuestionAnswer
How do I set powersaving mode? •
Windows XP: Set power-saving mode in Control Panel  → Appearance and Themes 
→ Display 
→  Screen Saver Settings or BIOS SETUP on the PC.
 •
Windows ME/2000: Set power-saving mode in Control Panel  → Display 
→  
Screen Saver Settings or BIOS SETUP on the PC.
 • Windows Vista: Set power-saving mode in Control Panel  → Appearance and Personalization 
→  Personalize 
→ Screen Saver Settings or BIOS SETUP on the PC.
 •
Windows 7: Set power-saving mode in Control Panel  → Appearance and Personalization 
→ 
Personalize  → Screen Saver Settings or BIOS SETUP on the PC.
 •
Windows 8: Set power-saving mode in Settings  → Control Panel 
→  
Appearance and Personalization  → Personalize 
→ Screen Saver Settings or BIOS SETUP on 
the PC.  
						

							165
Specifications
 -Size
 -Display area
H
V
 -Dimensions ( W x H x D)
W
D
H
General
Model Name UD46E-P UD55E-P / UD55E-S
PanelSize46 CLASS (45.9 Inches / 116.8 cm) 55 CLASS (54.6 Inches / 138.7 cm)
Display area1018.08 mm (H) x 572.67 mm ( V )
40.1 inches (H) x 22.5 inches ( V )1209.6 mm (H) x 680.4 mm ( V )
47.6 inches (H) x 26.8 inches ( V )
Dimensions (W x H x D)1022.1 x 576.6 x 97.4 mm
40.2 x 22.7 x 3.8 inches1213.5 x 684.3 x 96.6 mm
47.8 x 26.9 x 3.8 inches
Weight (without stand)16.2 kg / 35.7 Ibs
21.5 kg / 47.4 Ibs
Power SupplyAC 100 to 240 VAC (+/- 10%), 60 / 50 Hz ± 3 Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Environmental 
considerationsOperatingTemperature : 32 F – 104 F (0 C – 40 C)
Humidity : 10% – 80%, non-condensing
StorageTemperature : -4 F – 113 F (-20 C – 45 C)
Humidity : 5% – 95%, non-condensing
Chapter  14  
						

							166
 ―Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor 
settings.
Monitor installation takes place automatically. However, you can customize the installation settings if desired.
 ― Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect 
product performance.
 ― This device is a Class A digital apparatus.
[Recommendation] - EU Only
 • Hereby, Samsung Electronics, declares that this Monitor is in compliance with the essential requirements and other 
relevant provisions of Directive 1999/5/EC.
 •
The official Declaration of Conformity may be found at http://www.samsung.com/displaysolutions, go to Support > 
Search Product Support and enter the model name.
 •This equipment may only be used indoors.
 •This equipment may be operated in all EU countries.  
						

							167
PowerSaver
The power-saving function of this product reduces power consumption by switching off the screen and changing the colour of the power LED if the product is not used 
for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power-
savign mode only functions when the product is connected to a PC with a power-saving function.
PowerSaverNormal Operation Power saving mode
(SOG Signal : Not Support the 
DPM Mode)
Power off
(Power Button)
Power off
(Power Switch)RatingTypicalMax
Power IndicatorOff BlinkingOnOff
Power 
ConsumptionUD46E-P170 W
135 W187 WLess than 0.5 W Less than 0.5 W0 W
UD55E-P270 W217 W297 W
UD55E-S
 ―
The displayed power consumption level can vary in different operating conditions or when settings are changed.
 ―SOG(Sync On Green) is not supported.
 ―To reduce the power consumption to 0, turn off the switch at the back or disconnect the power cord. Disconnect the power cable if you will not be using the product 
for an extended period of time (during vacation, etc.).  
						

							168
Preset Timing Modes
 ―This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than 
the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
 ― Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85Hz, change the vertical 
frequency to 60Hz using the CDT product before you exchange it with the LCD product.
Model Name UD46E-P / UD55E-P / UD55E-S
SynchronizationHorizontal Frequency30 – 81 kHz
Vertical Frequency48 – 75 Hz
ResolutionOptimum resolution1920 x 1080 @ 60 Hz
Maximum resolution1920 x 1080 @ 60 Hz
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the PC 
does not belong to the standard signal modes, the screen may be blank with the power LED on. In such a case, change the settings according to the following table by 
referring to the graphics card user manual.
Resolution Horizontal Frequency
(kHz) Vertical Frequency
(Hz)Pixel Clock
(MHz)Sync Polarity
(H/V)
IBM, 720 x 400
31.469  70.087 28.322 -/+
MAC, 640 x 480 35.000  66.667 30.240 -/-
MAC, 832 x 624 49.726  74.551 57.284 -/-
MAC, 1152 x 870 68.681  75.062 100.000 -/-
VESA, 640 x 480 31.469  59.940 25.175 -/-
VESA, 640 x 480 37.861  72.809 31.500 -/-
 -
Horizontal Frequency
The time required to scan a single line 
from the left to the right side of the 
screen is called a horizontal cycle. The 
reciprocal number of a horizontal cycle 
is called horizontal frequency. Horizontal 
frequency is measured in kHz.
 - Vertical Frequency
The product displays a single image 
multiple times per second (like a 
fluorescent light) to display what the 
viewer sees. The rate of a single image 
being displayed repeatedly per second is 
called vertical frequency or refresh rate. 
Vertical frequency is measured in Hz.  
						

							169
ResolutionHorizontal Frequency
(kHz) Vertical Frequency
(Hz)Pixel Clock
(MHz)Sync Polarity
(H/V)
VESA, 640 x 480
37.500  75.000 31.500 -/-
VESA, 800 x 600 35.156  56.250 36.000 +/+
VESA, 800 x 600 37.879  60.317 40.000 +/+
VESA, 800 x 600 48.077  72.188 50.000 +/+
VESA, 800 x 600 46.875  75.000 49.500 +/+
VESA, 1024 x 768 48.363  60.004 65.000 -/-
VESA, 1024 x 768 56.476  70.069 75.000 -/-
VESA, 1024 x 768 60.023  75.029 78.750 +/+
VESA, 1152 x 864 67.500  75.000 108.000 +/+
VESA, 1280 x 720 45.000  60.000 74.250 +/+
VESA, 1280 x 800 49.702  59.810 83.500 -/+
VESA, 1280 x 1024 63.981  60.020 108.000 +/+
VESA, 1280 x 1024 79.976  75.025 135.000 +/+
VESA, 1366 x 768 47.712  59.790 85.500 +/+
VESA, 1440 x 900 55.935  59.887 106.500 -/+
VESA, 1600 x 900 60.000  60.000 108.000 +/+
VESA, 1680 x 1050 65.290  59.954 146.250 -/+
VESA, 1920 x 1080 67.500  60.000 148.500 +/+  
						

							170
Appendix
Responsibility for the Pay Service  
(Cost to Customers)
 ―When the service is requested, in spite of in warranty, we may charge you for a visit from a service 
technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
 • If a service technician gives instructions on how to use product or simply adjusts options without 
disassembling product.
 •If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
 •If a product is reinstalled or devices are connected additionally after installing the purchased 
product for the first time.
 •If a product is reinstalled to move to a different spot or to move to a different house.
 •If customer requests instructions on how to use because of another company's product.
 •If customer requests instructions on how to use the network or another company's programme.
 •
If customer requests software installation and setup for the product.
 •If a service technician removes/cleans dusts or foreign materials inside of the product.
 •If customer requests an installation additionally after purchasing a product through home-
shopping or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
 •External impact or drop.
 •Use of supplies or separatly sold product unspecified by Samsung.
 •Repair from a person besides an engineer of outsourcing service company or partner of Samsung 
Electronics Co., Ltd.
 •Remodeling or repairing the product by customer.
 •Using it with incorrect voltage or non-authorised electrical connections.
 •Not following the "cautions" in User Manual.
Others
 •If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
 •
If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp, 
Filter, Ribbon, etc.)
 ―
If customer requests a service in case the product has no defect, service fee may be charged. So 
please read User Manual first.
Chapter  15