Samsung Ud46d-p Manual

							To use this function, your mobile device 
should be supported by the Wi-Fi Direct.
Wi-Fi Direct
MENUm → Network → Wi-Fi Direct → ENTERE
Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router.
To connect your mobile device with your product using Wi-Fi Direct, follow these steps:
1 Go to Wi-Fi Direct screen. The product starts to search devices.
2 Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.
 •PBC (Push Button Configuration): Press the WPS(PBC) button on your Wi-Fi device within 2 minutes. Your product automatically acquires all the network setting 
values it needs and connects to your network.
 •PIN: Input the displayed PIN on your device.
 ―
If you want to disconnect the device, select the connected Wi-Fi device, and then select  Disconnected.
Multimedia Device Settings
MENUm → Network → Multimedia Device Settings → ENTERE
Allow other devices such as smart phones and tablets on your network, to share content with your product.  
						

							Server Network Settings
MENUm → Network → Server Network Settings → ENTERE
Connect to server
To run Player connect to a network.
 •If the SSL option is enabled, the server is configured to use https and data transfer is encrypted.
 ―
Enter the server IP address and port number. Use 7001 as the port number. (If unable to connect to 
the server using port number 7001, check with your server administrator to find the correct port 
number and then change the port number.)
MagicInfo Mode
Select the appropriate MagicInfo Mode depending on the environment where you are using the 
product.
 • MagicInfo
Server Access
Select a method to connect the server network.
 •Allow / Deny
FTP Mode
Specify the FTP operating mode.
 •
Active  / Passive
Device Name
MENUm → Network → Device Name → ENTERE
Select or enter a device name.
This name can be shown on network remote controls over the network.  
						

							System
Setup
MENU m → System → Setup → ENTER E
System
Setup
Time
Auto Source Switching
Power Control
Eco Solution
Temperature Control
Device Manager77
 -
The displayed image may differ depending on the model.
Initial settings (System)
After powering on the product for the first time, configure basic settings such as the language, channel and time.  
Press the 
 button.
 ― Enter your 4 digit PIN number. The default PIN number is “0-0-0-0". 
If you want to change the PIN number, use the Change PIN function.
1 Selecting a language 
Press the  u or 
d button, and then press the 
E button. Specify the OSD menu language.
2 Rotate menu
Configure the menu page orientation.
 -
Landscape / Portrait
3 Network Settings
Set up your network connection. Press the  E button to start. If you do not know your network set up information or 
want to set to it later, select Skip . You can set up the network connection later using the Network menu.
4 Clock Set
Set the current date and time, and then select Next .
5 Play via
Select the appropriate player mode depending on the environment where you are using the product.
 ―
The Play via setting step only appears when connected to the network.
6 Setup Complete
Congratulations! Setup is complete and you're ready to get started.  
						

							Time
MENU m → System → Time → ENTER E
Time
Clock Set
DST
Sleep Timer
Power On DelayOff
Off
0 sec
 - The displayed image may differ depending on the model.
You can configure Clock Set or Sleep Timer. You can also set the product to automatically turn on or off at a specified time 
using the Timer function.
 ―
Press the INFO button if you want to view the current time.
Clock Set
Select Clock Set. Select Date  or Time, and then press E.
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to 
move from one entry field to the next. Press E  when done.
 ―
You can set the Date  and Time directly by pressing the number buttons on the remote control.
DST
Switches the DST (Daylight Saving Time) function on or off.
Off / On
 •
Start Date: Set the start date of Daylight Saving Time.
 •
End Date: Set the end date of Daylight Saving Time.
 •Time Offset: Select the correct time offset your timezone.
Sleep Timer
Automatically shuts off the product after a preset period of time.
(Off / 30 min / 60 min / 90 min / 120 min / 150 min / 180 min)
 ―
Use the up and down arrows to select a period of time, and then press  E. To cancel Sleep Timer, select Off.
Power On Delay
When connecting multiple products, adjust the power-on time for each product to prevent power overload (within the range 
0–50 seconds).  
						

							Turning on the display with Auto Source Switching On, and the previous video source selection is not active, the display will 
automatically search the different video input sources for active video.
Auto Source Switching
When the Auto Source Switching is On , the display video source will automatically be searched for active video.
The Primary Source selection will be activated, if the current video source is not recognized.
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognized, the display will perform two searches for an active source, 
each search checking the primary and then secondary source. If both searches fail, the display will return to the first video 
source and display a message indicating that there is no signal.
When the Primary Source selection is set to All , the display will search all the video source inputs twice in sequence looking 
for an active video source, returning back to the first video source in the sequence if no video is found.
Primary Source Recovery
Select whether to restore the selected primary input source when a primary input source is connected.
 ― The Primary Source Recovery function is disabled if Primary Source is set to All .
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
Auto Source Switching
MENU m → System → Auto Source Switching → ENTER E
끄기
Auto Source Switching
Auto Source Switching
Primary Source Recovery
Primary Source
Secondary SourceOff
Off
All
HDMI
 - The displayed image may differ depending on the model.  
						

							Power Control
MENU m → System → Power Control → ENTER E
Power Control
Auto Power On
PC module power
Max. Power Saving
Standby Control
Power Button
Network Standby
OffOn
Auto
Power on only Off
 -The displayed image may differ depending on the model.
Auto Power On
This feature automatically turns on the product as soon as it is plugged in. Pressing the power button is not needed.
 • Off / On
PC module power
The PC module can be turned on/off separately from the LFD.
Synced power-on
To turn on the PC module without turning on the LFD, select Off.
 •Off / On
Synced power-off
To turn off the LFD without turning off the PC module, select  Off.
 •
Off / On
Max. Power Saving
Turns off the product to reduce power consumption after the PC has been left idle for a specified period of time.
 •Off / On
 ―
Available only PC, DVI , HDMI1, HDMI2, DisplayPort mode.  
						

							Standby Control
You can set the screen standby mode to be applied when an input signal is received.
 •Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
The message No Signal will appear if no source device is connected.
 •Off
The message No Signal will appear if no input signals are detected.
 ―
The Standby Control option is only enabled when Source  is set to PC, DVI, HDMI1, HDMI2 or DisplayPort.
 ―
If No Signal is displayed although a source device is connected, check the cable connection.
 ―If No Signal Message is set to Off,the No Signal message does not appear.
If this is the case, set No Signal Message to On .
 •
On
Power-saving mode will activate if no input signals are detected.
Power Button
The power button can be set to either turn on the power or turn on/off the power.
 •Power on only: Set the power button to turn on the power.
 •
Power on and off: Set the power button to turn on/off the power.
Network Standby
This feature keeps the network power on when the product turns off.
 •Off / On
Power Control
Auto Power On
PC module power
Max. Power Saving
Standby Control
Power Button
Network Standby
Off
On
Auto
Power on only Off
 -The displayed image may differ depending on the model.  
						

							Eco Solution
MENU m → System → Eco Solution → ENTER E
Eco Solution
Energy Saving
Eco Sensor
Screen Lamp Schedule
No Signal Power Off
Auto Power Off
Off
Off
Off
Off
Off
 -The displayed image may differ depending on the model.
Energy Saving
Reduce the power consumption by adjusting the screen brightness.
 • Off / Low  / Medium / High
Eco Sensor
To enhance your power savings, the picture settings will automatically adapt to the light in the room.
 •
Off / On
 ―
Adjusting the High setting under Picture while Eco Sensor is on will disable the Off.
Min. Backlight
When Eco Sensor is On , you can manually adjust the minimum screen brightness. Min. Backlight is the darkest backlight 
mode. Make sure the Min. Backlight setting is lower than the Backlight setting.
 ― If Eco Sensor is On , the display brightness may change (become slightly darker or brighter) depending on the surrounding 
light intensity. 
Screen Lamp Schedule
Adjust the panel brightness. A value closer to 100 makes the panel brighter.
 • Off / On  
						

							Eco Solution
Energy Saving
Eco Sensor
Screen Lamp Schedule
No Signal Power Off
Auto Power Off
Off
Off
Off
Off
Off
 -The displayed image may differ depending on the model.
No Signal Power Off
Save power by turning the device off when no signal is received from any source.
 • Off / 15 min / 30 min / 60 min
 ―
Disabled when an attached PC is in power saving mode.
 ―The product will automatically power off at a specified time. The time can be changed as required.
Auto Power Off
The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel 
within select hours to prevent overheating.
 • Off / 4 hours / 6 hours / 8 hours
This function detects the internal temperature of the product. You can specify the temperature range that is acceptable.
The default temperature is set to 77
C.
The recommended operating temperature for this product is 75 to 80C (based on an ambient temperature of 40C).
 ― The screen will become darker if the current temperature exceeds the specified temperature limit. If the temperature 
continues to rise, the product will power off to prevent overheating.
Temperature Control
MENU m → System → Temperature Control → ENTER E
System
Temperature Control 77
 -
The displayed image may differ depending on the model.  
						

							Device Manager
MENU m → System → Device Manager → ENTER E
Device Manager
Keyboard Settings
Mouse Settings
Pointer Settings
 -The displayed image may differ depending on the model.
Configure options for external input devices connected to the product.
Keyboard Settings
Connecting a keyboard to the product displays the Keyboard Settings menu.
Select Keyboard
Select a keyboard you want to use from the available connected keyboards.
 ―
It is possible to use only one connected keyboard.
Keyboard Options
 ―Depending on the country.
Keyboard Language
Specify the keyboard input language.
Keyboard type
Specify the keyboard type.
Switch Input Language
Configure the key combination used to change the input language.