Samsung SyncMaster P50H, P50FP, P63FP Pdp Monitor User Manual

							2. Before 
drilling into the wall, check if the length between the two locking holes at the back
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length. A -
Length between the two locking holes
3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to 
 drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A. To mount the product on the wall bracket
The 
 shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
1. Remove the 4 screws on the back of the product. Introduction 
						

							2. Insert the screw B into the plastic hanger.
Notice
• Mount 
the product on the wall bracket and make sure it is properly fixed to the left
and right plastic hangers.
• Be careful when installing the product on the bracket as fingers can be caught in the holes.
• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.
3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. 4. Remove 

safety pin (3) and insert the 4 product holders into the corresponding bracket
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket. Introduction 
						

							A -
PDP Display
B - Wall Bracket
C - Wall
Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket.
2. Hold 
the  product  at  the  top  in  the  center  and  pull  it  forward  (direction  of  the  arrow)  to
adjust the angle.  Note
You can adjust the bracket angle between -2° and 15°. Make sure to use the top center, and not the left or the right side of the product to adjust the
angle. Introduction 
						

							Mechanical Layout (P63FP)
Mechanical Layout
PDP Display Head
Wall Bracket Installation
• Contact a technician for installing the wall bracket.
• SAMSUNG  Electronics  is  not  responsible  for  any  damages  to  the  product  or  harm  to customers when the installation is done by the customer.
• This  product  is  for  installing  on  cement  walls.  The  product  may  not  stay  in  place  when installed on plaster or wood.
Components Only use the components and accessories shipped with the product. Wall Bracket(1) Hinge(Left  1,  Right
1)Plastic
Hanger
(4)Screw
(A)(11)
Screw
(B)(4)Anchor
(11)
Introduction 
						

							Wall Bracket Assembly
 Note
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one.
A - Captive Screw
B - Wall Bracket
C - Hinge (Left)
D - Hinge (Right)
2. Before 
 drilling into the wall, check if the length between the two locking holes at the back
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length. A -
Length between the two locking holesIntroduction 
						

							3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to  drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A. To mount the product on the wall bracket
The 
 shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
1. Remove the 4 screws on the back of the product. 2. Insert the screw B into the plastic hanger.
Notice
• Mount 

the product on the wall bracket and make sure it is properly fixed to the left
and right plastic hangers.
• Be careful when installing the product on the bracket as fingers can be caught in the holes.
• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. Introduction 
						

							3. Tighten 
the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. 4. Remove 

safety pin (3) and insert the 4 product holders into the corresponding bracket
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A -
PDP Display
B - Wall Bracket
C - Wall
Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket.
2. Hold 

the  product  at  the  top  in  the  center  and  pull  it  forward  (direction  of  the  arrow)  to
adjust the angle.  Note
You can adjust the bracket angle between -2° and 15°. Introduction 
						

							Make sure to use the top center, and not the left or the right side of the product to adjust the
angle.
Introduction 
						

							Connections
Connecting a Computer
Using a Power cord with Earth
•
In 
the event of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.  Note
AV 
 input devices such as DVD players, VCRs or camcorders as well as your computer can
be connected to the PDP Display. For detailed information on connecting AV input devices,
refer to the contents under Adjusting Your PDP Display. Connect  the  power  cord  for  your  PDP  Display  to  the  power  port  on  the
back of the PDP Display. Turn on the power switch.
There are 2 ways to connect the D-sub to your PDP Display. Choose one
of the following:
  Using the D-sub (Analog) connector on the video card.
• Connect 
 the  D-sub  to  the  15-pin,  RGB  port  on  the  back  of  your  PDP
Display and the 15 pin D-sub Port on the computer.  
Using the DVI (Digital) connector on the video card.
• Connect 
 the DVI Cable to the DVI(HDCP) port on the back of your PDP
Display and the DVI port on the computer.  
Using the BNC (Analog) connector on the video card. 
						

							• Connect 
the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V
ports  on  the  back  of  your  PDP  Display  and  the  15  pin  D-sub  Port  on
the computer. Connect the audio cable for your PDP Display to the audio port on the back
of your computer.
 Note
•

Turn on both your computer and the PDP Display.
• The DVI cable is optional.
• Contact a local SAMSUNG Electronics Service Center to buy optional items.
Connecting to Other devices Using a Power cord with Earth
•
In 

the event of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.  Note
AV 
 input devices such as DVD players, VCRs or camcorders as well as your computer can
be connected to the PDP Display. For detailed information on connecting AV input devices,
refer to the contents under Adjusting Your PDP Display.
Connecting AV Devices 1. Connect 

the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of
the PDP Display.
2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.
3. Select  AV using the SOURCE .  Note
The 
 PDP Display has AV connection terminals to connect AV input devices like DVDs, VCRs
or Camcorders. You may enjoy AV signals as long as the PDP Display is turned on. Connections