Samsung SyncMaster P50H, P50FP, P63FP Pdp Monitor User Manual

							• The ferrite  cores  are  used  to  shield  the  cables  from  interfer-
ence.
• When  connecting  a  cable,  open  the  ferrite  core  and  clip  it around the cable near the plug.
Your PDP Display
Front
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only al-
lowed  for  external  devices  that  are  connected  to  the  PDP  Display  at  the
time.
[PC] → [ DVI] → [ AV] → [HDMI] → [ Component] → [ BNC]
Enter button []
Activates a highlighted menu item.
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
- VOL+
Moves  from  one  menu  item  to  another  horizontally  or  adjusts  selected
menu values. When OSD is not on the screen, push the button to adjust
volume.
 SEL  Moves from one menu item to another vertically or adjusts selected menu
values.
/ When OSD is not on the screen, push the button to adjust channel. Introduction 
						

							Power button []
Use this button for turning the PDP Display on and off.
Power indicator
Shows PowerSaver mode by blinking green Note
See PowerSaver described 
 in the manual for further information regarding
power saving functions. For energy conservation, turn your PDP Display
OFF when it is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the PDP Display. Rear
 Note
For  detailed 

information  concerning  cable  connections,  refer  to  Connecting  Cables  under
Setup. The PDP Display 's configuration at the back may vary slightly depending on the PDP
Display model.
 POWER IN
The  power  cord  plugs  into  the  PDP  Display
and the wall plug.  Introduction 
						

							 RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
 RGB IN (PC Video Connection Terminal)
Using  a  D-Sub  Cable  (15  pin  D-Sub)  -  PC
mode (Analog PC)
 DVI IN (PC Video Connection Terminal)
Using  a  DVI  Cable  (DVI-D  to  DVI-D)  -  DVI
mode (Digital PC)
 DVI / PC / HDMI IN [DVI/PC/HDMI AU-
DIO  IN]  (PC/DVI/HDMI  Audio  Connection Terminal (Input))  
 AV / COMPONENT AUDIO IN [L- AUDIO
- R
]
Connect  the  port  of  the  DVD,  VCR  (DVD  /
DTV Set-Top Box) to the [ L- AUDIO - R ] port
of the PDP Display.
 AV IN [VIDEO]
Connect the [ VIDEO ] terminal of your mon-
itor to the video output terminal of the exter-
nal device using a VIDEO cable.
 AUDIO OUT
Headphone output terminal.
 DVI OUT
Connect  a  monitor  to  another  monitor
through a DVI cable.
Can connect up to 10 PDP display units.
 HDMI IN
Connect  the  HDMI  terminal  at  the  back  of
your  PDP  Display  to  the  HDMI  terminal  of
your  digital  output  device  using  a  HDMI  ca-
ble.  Introduction 
						

							 BNC OUT [R/PR, G/Y, B/PB, H, V]
(BNC Terminal (Output))
BNC  (Analog  PC)  Connection:  connecting
the R, G, B, H, V ports.
  BNC/COMPONENT  IN[R/PR,  G/Y,  B/
PB, H, V]
(BNC/Component  Connection  Terminal  (In-
put))  
Kensington Lock
The  Kensington  Lock  is  a  device  used  to
physically  fix  the  system  when  using  it  in  a
public  place.  The  locking  device  has  to  be
purchased separately. The appearance and
locking  method  may  differ  from  the  illustra-
tion depending on the manufacturer. Refer to
the  manual  provided  with  the  Kensington
Lock for proper use. The locking device has
to be purchased separately.
 Note
The location of the Kensington Lock may be
different depending on its model.
Using 

the Anti-Theft Kensington Lock
1. Insert  the  locking  device  into  the  Ken- sington slot on the Monitor  and turn
it in the locking direction  .
2.

Connect the Kensington Lock cable.
3. Fix  the  Kensington  Lock  to  a  desk  or  a heavy stationary object.  Note
See Connecting Cables
  for further information regarding cable connections.
Remote Control  Note
The 
 performance of the remote control may be affected by a TV or other electronic device
operating near the PDP Display , causing a malfunction due to interference with the frequen-
cy. Introduction 
						

							 POWER
OFF
Number Buttons
DEL   button
+ VOL -
 MUTE
TV/DTV
 MENU
 INFO
Color Buttons
 TTX/MIX
STILL
AUTO
S.MODE
MDC
LOCK
 SOURCE
 ENTER/PRE-CH
 CH/P 
D.MENU
GUIDE
 RETURN
Up-Down Left-Right buttons
 EXIT
 SRS
MagicInfo
P.MODE
 DUAL/MTSPIP
SWAP
1. 
 POWER
Turns the product On.
2.   Off
Turns the product Off.
3. Number Buttons
 Press to change the channel.
4. DEL   button
The 
 "-"  button  operates  only  for  DTV.  It  is  used  to  select
MMS (multi-channel) for a DTV. Introduction 
						

							5. + VOL -
Adjusts the audio volume.
6.   MUTE
Pauses  (mutes)  the  audio  output  temporarily.  This  is  dis-
played  on  the  lower  left  corner  of  the  screen.  The  audio
resumes if MUTE or - VOL + is pressed in the Mute mode.
7. TV/DTV Selects the TV and DTV mode directly.
8.   MENU
Opens 
 the  on-screen  menu  and  exits  from  the  menu  or
closes the adjustment menu.
9.  Activates a highlighted menu item.
10.   INFO
Current 
 picture  information  is  displayed  on  the  upper  left
corner of the screen.
11. Color Buttons Press to add or delete channels and to store channels to the
favorite channel list in the “Channel List” menu.
12.   TTX/MIX
TV 
 channels  provide  written  information  services  via  tele-
text.
- Teletext Buttons For more information > TTX / MIX
13. STILL Press 

the button once to freeze the screen. Press it again
to unfreeze.
14. AUTO Adjusts  the  screen  display  automatically  in  PC  mode.  By
changing the resolution in the control panel, auto function is
performed.
15. S.MODE When pressing this button, the current mode is displayed at
the  bottom  centre  of  the  screen.  The  PDP  Display  has  a
built-in high fidelity stereo amplifier. Then press the button
again  to  circle  through  available  preconfigured  modes.
( Standard → Music  → Movie  → Speech  → Custom )
16. MDC MDC Quick Launch Button.
17. LOCK Activates or deactivates all function keys on both the remote
control and the PDP Display except for the Power and LOCK
buttons.
18.   SOURCE
Press the button to change the input signal SOURCE.
Changing 

the SOURCE is only allowed for external devices
that are connected to the monitor at the time.
19.   ENTER/PRE-CH
This 
 button  is  used  to  return  to  the  immediately  previous
channel.
20.  CH/P In TV mode, selects TV channels.
21. D.MENU

DTV menu display
22. GUIDE Electronic Program Guide (EPG) display. Introduction 
						

							23.   RETURN
Returns to the previous menu.
24. 
Up-Down Left-Right but-
tons Moves from one menu item to another horizontally, vertically
or adjusts selected menu values.
25.   EXIT
Exits from the menu screen.
26.   SRS
Selects SRS TruSurround XT mode.
27. MagicInfo
 MagicInfo Quick Launch Button.
28. P.MODE When  you  press  this  button,  current  picture  mode  is  dis-
played on the lower center of the screen.
AV / HDMI / TV : P.MODE
The  PDP  Display  has  four  automatic  picture  settings  that
are  preset  at  the  factory.  Then  push  button  again  to  circle
through  available  preconfigured  modes.  (  Dynamic →
Standard  → Movie  → Custom )
PC / DVI / MagicInfo: M/B (MagicBright)
MagicBright is a feature providing the optimum viewing en-
vironment depending on the contents of the image you are
watching. Then push button again to circle through available
preconfigured modes. (Entertain  → Internet  → Text  → Cus-
tom )
29.   DUAL/MTS
DUAL-
STEREO/MONO,  DUAL  l  /  DUAL  ll  and  MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote
control while watching TV.
MTS-
You can select MTS (Multichannel Television Stereo) mode.
Audio Type MTS/S_Mode Default
FM Stereo Mono Mono Manual
Change
Stereo Mono ↔ Stereo
SAP Mono ↔ SAP Mono
30. 
PIPEvery time you press the button, a PIP screen appears.
- This fuction does not work for this PDP Display.
31.
 SWAPSwaps the contents of the PIP and main image. The image
in the PIP window will appear on the main screen, and the
main screen image will appear in the PIP window.
- This fuction does not work for this PDP Display. Introduction 
						

							Mechanical Layout (P50HP, P50FP)
Mechanical Layout
PDP Display Head Introduction 
						

							Installation VESA Bracket
• When installing VESA, make sure to comply with the international VESA standards.
• Purchasing  VESA  Bracket  and  Installation  Information  :  Please  contact  your  nearest SAMSUNG  Distributor  to  place  an  order.  After  your  order  is  placed,  installation  profes-
sionals will visit you and install the bracket.
• At least 2 persons are needed in order to move the PDP Display.
• SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion.
Dimensions Notice
For 

securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12
mm length. Introduction 
						

							Wall Bracket Installation
• Contact a technician for installing the wall bracket.
• SAMSUNG  Electronics  is  not  responsible  for  any  damages  to  the  product  or  harm  to customers when the installation is done by the customer.
• This  product  is  for  installing  on  cement  walls.  The  product  may  not  stay  in  place  when installed on plaster or wood.
Components Only use the components and accessories shipped with the product. Wall Bracket(1) Hinge(Left  1,  Right
1)Plastic
Hanger
(4)Screw
(A)(11)
Screw
(B)(4)Anchor
(11)
Wall Bracket Assembly  Note
There are two hinges(left and right). Use the correct one.
1.

Insert and tighten the Captive Screw in the direction of the arrow.When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one.
A - Captive Screw
B - Wall Bracket
C - Hinge (Left)
D - Hinge (Right)Introduction