Samsung SyncMaster 320MP-2 LCD Monitor User Manual

 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click Update Driver... in the Driver tab. 7.
Check the Browse my computer for driver software checkbox and click L\
et me pick from a
list of device drivers on my computer. 8.
Click Have Disk...” and select the folder (for example, D:\Drive)\
 where the driver setup file is
located, and click OK. Using the Software 

9.
Select the model that matches your monitor from the list of monitor mode\
ls on the screen, and
click Next.  
10. Click Close → Close → OK  → OK on the following screens displayed in sequence.Microsoft
®
 Windows ®
 XP Operating System Using the Software 

1. Insert CD into the CD-ROM drive.
2.
Click Start → Control Panel then click the Appearance and Themes icon. 3. Click Display icon and choose the Settings tab then click Advanced.\
...
4. Click the Properties button on the Monitor tab and select Driver t\
ab.
5. Click Update Driver... and select Install from a list or... then cli\
ck Next button.
6. Select Dont search, I will... then click Next and then click Have \
disk. Using the Software 

7.
Click the Browse button then choose A:(D:\Driver) and choose your m\
onitor model in the model
list and click the Next button. 8.
If you can see following message window, then click the Continue Anyway\
 button. Then click
OK button.  
 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9. Click the Close button then click OK button continually. Using the...

 
10. Monitor driver installation is completed.
Microsoft ®
 Windows ®
 2000 Operating System
When you can see Digital Signature Not Found on your monitor, follow t\
hese steps.
1. Choose OK button on the Insert disk window. 2. Click the Browse button on the File Needed window.
3. Choose A:(D:\Driver) then click the Open button and then click OK\
 button.
How to install
1. Click Start, Setting, Control Panel.
2. Double click the Display icon.
3.
Select the Settings tab and click Advanced Properties...

4. Select the Monitor tab.
5. Click the Change button in the Monitor Type area.
6. Choose Specify the location of the driver.
7. Choose Display a list of all the driver in a specific location... then\
 click Next button.
8. Click the Have Disk button.
9.
Specify A:\(D:\driver) then click OK button.
10. Select Show all devices and choose the monitor that corresponds to the\
 one you connected to
your computer and click OK.
11. Continue choosing Close button and OK button until you close the Dis\
play...

 
 
 
 
Introduction  
 
 
 A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously 
operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and 
a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a 
display.
Main Screen 
 
  Click Start > Program > Samsung > MDC System to start the program. 
  Select a set to see the volume of the selected...

 
  
Main IconsSelect Button
RemoconInfo Grid
Safety LockDisplay Selection
Port SelectionControl Tools 
1. Use the main icons to switch into each screen.
2. Allows you to enable or disable the remote control signal receiving function of the display unit. 
3. Set the Safety Lock function. 
When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
4. The setting for the PC Serial Port can change. The original value is COM1. 
5. Click Select all or Clear to...

 
 
1. The Multiple Display Control is originally set to COM1.
2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu.
3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 
4. The selected port is stored in the program and used for the next program as well.  
 Power Control 
 
1. Click Power Control of the main icons and the Power Control screen appears. 

 
Info Grid shows some basic information necessary to Power Control.
  1)  (Power Status)
 2) Input 
 3) Image Size
 4) On Timer
 5) Off Timer
2. Use the Select All button or Check Box to choose a display to control.
 Power Control allows controlling some of the functions of the selected display. 
1) Power On/Off