Samsung SyncMaster 320MP-2 LCD Monitor User Manual

2. Insert the screw B into the plastic hanger.
Notice
• Mount the product on the wall bracket and make sure it is properly fixed\
 to the left and right
plastic hangers.
• Be careful when installing the product on the bracket as fingers can be \
caught in the holes.
• Make sure the wall bracket is securely fixed to the wall, or the product\
 may not stay in place
after installation.
3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear h\
oles of the product. 4.
Remove safety pin (3)...

A -
LCD Display
B - Wall Bracket
C - Wall
Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket.
2.
Hold the product at the top in the center and pull it forward (directio\
n of the arrow) to adjust the
angle.  Note
You can adjust the bracket angle between -2° and 15°. Make sure to use the top center, and not the left or the right side of t\
he product to adjust the angle. Introduction 

Connections
Connecting a Computer
Using a Power cord with Earth
•
In the event of failure, the earth lead may cause electric shock. Make s\
ure to
wire the earth lead in correctly, before connecting the AC power. When u\
n-
wiring the earth lead, make sure to disconnect the AC power in advance.  Note
AV input devices such as DVD players, VCRs or camcorders as well as your\
 computer can be connected
to the LCD Display. For detailed information on connecting AV input devi\
ces, refer to the contents
under...

 
 Using the BNC (Analog) connector on the video card.
• Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V ports
on the back of your LCD Display and the 15 pin D-sub Port on the compute\
r. Connect the audio cable for your LCD Display to the audio port on the ba\
ck of
your computer.
 Note
• Turn on both your computer and the LCD Display.
• The DVI cable is optional.
• Contact a local SAMSUNG Electronics Service Center to buy optional items.
Connecting to Other devices Using a Power cord with...

1.
Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUD\
IO-L] port of the
LCD Display.
2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.\
3. Select  AV using the SOURCE .  Note
The LCD Display has AV connection terminals to connect AV input devices \
like DVDs, VCRs or
Camcorders. You may enjoy AV signals as long as the LCD Display is turne\
d on.
Connecting to a Camcorder 1.
Locate the AV output jacks on the camcorder. They are usually found on t\
he side or...

1.
Connect a set of audio cables between the AV AUDIO IN [L-AUDIO-R] on the\
 LCD Display
and the AUDIO OUT jacks on the DVD player.
2. Connect a Component cable between the BNC/COMPONENT IN- P
R, Y, P
B port on the LCD
Display and the P R, Y, P
B jacks on the DVD player.  Note
• Select Component for the connection to a DVD player using the SOURCE but\
ton on the front of
the LCD Display or on the remote control.
• Then, start the DVD Player with a DVD disc inserted.  Note
• A component cable is...

 Note
• For an explanation of Component video, see your Set Top Box owners manu\
al.
Connecting Using a HDMI Cable  Note
• Input devices such as digital DVD are connected to the HDMI terminal of \
the LCD Display using
the HDMI cable.
• You cannot connect a PC to the HDMI terminal.
Connecting Using a DVI to HDMI Cable  Note
• Connect the DVI output terminal of a digital output device to the HDMI t\
erminal of the LCD
Display using a DVI to HDMI cable.
• Connect the red and white jacks of an RCA to stereo...

 Note
• Connect a set of audio cables between the AUX L, R jacks on the AUDIO SY\
STEM and AUDIO
OUT [L-AUDIO-R] on LCD Display. Connections 

Using the Software
Monitor Driver
 Note
When prompted by the operating system for the monitor driver, insert the\
 CD-ROM
included with this monitor. Driver installation is slightly different fr\
om one operating
system to another. Follow the directions appropriate for the operating s\
ystem you
have.
Prepare a blank disk and download the driver program file at the Interne\
t web site
shown here.
Internet web site :
http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic)
1. Insert...

 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual) Microsoft®
 Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2. Click  (Start) and Control Panel. Then, double-click on Appearance and Per\
sonalization.
3. Click Personalization and then Display Settings.
4. Click Advanced Settings....
 
5....