Samsung SyncMaster 320MP-2 LCD Monitor User Manual

							 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click Update Driver... in the Driver tab. 7.
Check the Browse my computer for driver software checkbox and click L\
et me pick from a
list of device drivers on my computer. 8.
Click Have Disk...” and select the folder (for example, D:\Drive)\
 where the driver setup file is
located, and click OK. Using the Software 
						

							9.
Select the model that matches your monitor from the list of monitor mode\
ls on the screen, and
click Next.  
10. Click Close → Close → OK  → OK on the following screens displayed in sequence.Microsoft
®
 Windows ®
 XP Operating System Using the Software 
						

							1. Insert CD into the CD-ROM drive.
2.
Click Start → Control Panel then click the Appearance and Themes icon. 3. Click Display icon and choose the Settings tab then click Advanced.\
...
4. Click the Properties button on the Monitor tab and select Driver t\
ab.
5. Click Update Driver... and select Install from a list or... then cli\
ck Next button.
6. Select Dont search, I will... then click Next and then click Have \
disk. Using the Software 
						

							7.
Click the Browse button then choose A:(D:\Driver) and choose your m\
onitor model in the model
list and click the Next button. 8.
If you can see following message window, then click the Continue Anyway\
 button. Then click
OK button.  
 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9. Click the Close button then click OK button continually. Using the Software 
						

							 
10. Monitor driver installation is completed.
Microsoft ®
 Windows ®
 2000 Operating System
When you can see Digital Signature Not Found on your monitor, follow t\
hese steps.
1. Choose OK button on the Insert disk window. 2. Click the Browse button on the File Needed window.
3. Choose A:(D:\Driver) then click the Open button and then click OK\
 button.
How to install
1. Click Start, Setting, Control Panel.
2. Double click the Display icon.
3.
Select the Settings tab and click Advanced Properties button.
4. Choose Monitor. Case1 : If the Properties button is inactive, it means your monitor is\
 properly configured. Please
stop installation
Case2 : If the Properties button is active, click the Properties but\
ton then follow next steps
continually.
5. Click Driver and then click on Update Driver... then click on the N\
ext button.
6. Choose Display a list of the known drivers for this device so that I ca\
n choose a specific driver
then click Next and then click Have disk.
7. Click the Browse button then choose A:(D:\Driver).
8. Click the Open button, then click OK button.
9. Choose your monitor model and click the Next button then click Next \
button.
10. Click the Finish button then the Close button. If you can see the Digital Signature Not Found window then click the \
Yes button. And click
the Finish button then the Close button.
Microsoft ®
 Windows ®
 Millennium Operating System
1. Click Start, Setting, Control Panel.
2. Double click the Display icon.
3. Select the Settings tab and click Advanced Properties button. Using the Software 
						

							4. Select the Monitor tab.
5. Click the Change button in the Monitor Type area.
6. Choose Specify the location of the driver.
7. Choose Display a list of all the driver in a specific location... then\
 click Next button.
8. Click the Have Disk button.
9.
Specify A:\(D:\driver) then click OK button.
10. Select Show all devices and choose the monitor that corresponds to the\
 one you connected to
your computer and click OK.
11. Continue choosing Close button and OK button until you close the Dis\
play Properties dia-
logue box.
Microsoft ®
 Windows ®
 NT Operating System
1.
Click Start, Settings, Control Panel, and then double-click Displ\
ay icon.
2. In Display Registration Information window, click Settings Tab and then \
click All Display
Modes.
3. Select a mode that you wish to use (Resolution, Number of colors and Ve\
rtical frequency) and
then click OK.
4. Click Apply button if you see the screen working normally after clicki\
ng Test. If the screen
is not normal, change to a different mode (lower mode of resolution, co\
lors or frequency).  Note
If there is no Mode at All Display Modes, select the level of resolution\
 and vertical frequency by
referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a typ\
e of system setting file.
1. Press Enter at the first and the second screen after executing the X86\
Config file.
2. The third screen is for setting your mouse.
3. Set a mouse for your computer.
4. The next screen is for selecting a keyboard.
5. Set a Keyboard for your computer.
6.

The next screen is for setting your monitor.
7. First of all, set a horizontal frequency for your monitor. (You can ent\
er the frequency directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency\
 directly.)
9. Enter the model name of your monitor. This information will not affect t\
he actual execution of
X-Window.
10. You have finished setting up your monitor. Execute X-Window after settin\
g other requested
hardware. Using the Software 
						

							 
 
 
 
Introduction  
 
 
 A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously 
operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and 
a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a 
display.
Main Screen 
 
  Click Start > Program > Samsung > MDC System to start the program. 
  Select a set to see the volume of the selected set within the slider.  
						

							 
  
Main IconsSelect Button
RemoconInfo Grid
Safety LockDisplay Selection
Port SelectionControl Tools 
1. Use the main icons to switch into each screen.
2. Allows you to enable or disable the remote control signal receiving function of the display unit. 
3. Set the Safety Lock function. 
When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
4. The setting for the PC Serial Port can change. The original value is COM1. 
5. Click Select all or Clear to select or clear all displays.
6. Use Grid to view brief information on selected display.
7. Select a display from Display Selection. 
8. Use Control Tools to control displays.
   The remote control Enable/Disable function operates whether or not the power is On/Off, and this 
applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is 
shut down, the remote control signal receiving function of all displays is initialized to Enable when the 
MDC is closed.
Port Selection  
  
						

							 
 
1. The Multiple Display Control is originally set to COM1.
2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu.
3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 
4. The selected port is stored in the program and used for the next program as well.  
 Power Control 
 
1. Click Power Control of the main icons and the Power Control screen appears. 
						

							 
Info Grid shows some basic information necessary to Power Control.
  1)  (Power Status)
 2) Input 
 3) Image Size
 4) On Timer
 5) Off Timer
2. Use the Select All button or Check Box to choose a display to control.
 Power Control allows controlling some of the functions of the selected display. 
1) Power On/Off