Samsung SyncMaster 320MP-2 LCD Monitor User Manual

							Removes noise such as vertical stripes. Coarse adjustment may move the s\
creen image area. You may
relocate it to the center using the horizontal control menu.
Fine MENU →   → ENTER → [Picture] →   →   →   →   → ENTER → [Image Lock] →   → ENTER
→ [Fine] →  ,   → ENTER
Removes noise such as horizontal stripes. If the noise persists even aft\
er Fine tuning, repeat it after
adjusting the frequency (clock speed).
H-Position MENU →   → ENTER → [Picture] →   →   →   →   → ENTER → [Image Lock] →   → 
→ ENTER → [H-Position] →  ,   → ENTER
Adjusts the screen location horizontally.
V-Position MENU →   →
 ENTER  → [Picture]  →   →   →   →   →
 ENTER  → [Image Lock ] →   →   →
 → ENTER → [V-Position] →  ,   → ENTER
Adjusts the screen location vertically.
Auto Adjustment  MENU →   → ENTER → [Picture] →   →   →   →   →   → ENTER → [Auto Adjustment ]
The values of 
Fine, Coarse, Position are adjusted automatically. By changing the resolution in the
control panel, the auto function is performed.
(Available in  PC mode only)  Note
The direct button on the remote control is the AUTO button.
Signal Balance  This is used to make up for the weak RGB signal transmitted by a long si\
gnal cable.
MENU → 
 → ENTER → [Picture] →   →   →   →   →   →   → ENTER → [Signal Bal-
ance]
(Available in  PC mode only) Adjusting the LCD Display 
						

							Signal Balance
MENU →   → ENTER → [Picture] →   →   →   →   →   →   → ENTER → [Signal Bal-
ance] → ENTER → [Signal Balance] →   ,   → ENTER
Selects either 
On or Off with the signal control.
Signal Control MENU →   → ENTER → [Picture] →   →   →   →   →   →   → ENTER → [Signal Bal-
ance] →   → ENTER → [Signal Control]
1. R-Gain
MENU →   → ENTER → [Picture] →   →   →   →   →   →   → ENTER → [Signal
Balance] →   → ENTER → [Signal Control] → ENTER → [R-Gain] →  ,   → ENTER
2.
G-Gain
MENU →   → ENTER → [Picture] →   →   →   →   →   →   → ENTER → [Signal
Balance]  →   →
 ENTER → [ Signal Control ] →   →
 ENTER → [ G-Gain] →  ,   →
 ENTER 3.
B-Gain
MENU →   → ENTER → [Picture] →   →   →   →   →   →   → ENTER → [Signal
Balance] →   → ENTER → [Signal Control] →   →   → ENTER → [B-Gain] →  ,   →
ENTER 4.
R-Offset
MENU →   → ENTER → [Picture] →   →   →   →   →   →   → ENTER → [Signal
Balance]  →   →
 ENTER → [ Signal Control ] →   →   →   →
 ENTER → [ R-Offset] →  ,
 → ENTER
5.
G-Offset
MENU →   → ENTER → [Picture]→  →  →  →  →  →  → ENTER → [Signal Bal-
ance]  →  → ENTER 
→ [Signal Control ] →   →   →   →   →
 ENTER → [G-Offset]  →  ,
→ ENTERAdjusting the LCD Display 
						

							6.
B-Offset
MENU →   → ENTER → [Picture]→  →  →  →   ℜ→ →  → ENTER → [Signal Bal-
ance]  →  → ENTER → [
Signal Control ] →  →   →   →   →   →
 ENTER → [B-Offset]  → ,  → ENTER
Size 
MENU 
→   →
 ENTER  → [Picture]  →   →   →   →   →  →  →   →
 ENTER  → [Size]  →   ,
→ ENTER
The Size can be switched.
1.
16:9
2. 4:3
Dynamic Contrast  MENU 
→   →
 ENTER → [ Picture] →   →   →   →   →   →   →   →
 ENTER → [ Dynamic
Contrast ] →   ,   → ENTER
Dynamic Contrast automatically detects the distribution of the visual signal and adjusts\
 to create an
optimum contrast.
1. Off
2. On Adjusting the LCD Display 
						

							Picture [ AV / HDMI / Component Mode]
Available Modes
•  PC / BNC / DVI
•  AV
•  HDMI
•  Component
 Note
• The TV menu is available when a TV tuner box is installed.
• The MagicInfo menu is available when a network box is installed.
Mode  MENU →   → ENTER → [Picture] → ENTER → [Mode] →   ,   → ENTER
The LCD Display has four automatic picture settings (
Dynamic, Standard,  Movie and Cus-
tom) that are preset at the factory.
Dynamic, Standard, Movie, or Custom can be activated.
1. Dynamic
2. Standard
3. Movie
4. Custom  Note
The direct button on the remote control is the P.MODE button.
Custom  By using the on-screen menus, the contrast and brightness can be changed\
 to your personal preference.
MENU → 
 → ENTER → [Picture] →   → ENTER → [Custom]
Contrast MENU →   →
 ENTER  → [Picture]  →   →
 ENTER  → [Custom]  → ENTER  → [Contrast]  →  ,
 → ENTERAdjusting the LCD Display 
						

							Adjusts the Contrast.
Brightness MENU →   → ENTER → [Picture] →   → ENTER → [Custom] →   → ENTER → [Bright-
ness] →  ,   → ENTER
Adjusts the Brightness.
Sharpness MENU →   → ENTER → [Picture] →   → ENTER → [Custom] →   →   → ENTER →
[Sharpness] →  ,   → ENTER
Adjusts the picture Sharpness.
Color MENU →   → ENTER → [Picture] →   → ENTER → [Custom] →   →   →   → ENTER →
[Color] →  ,   → ENTER
Adjusts the picture Color.
Tint MENU →   →
 ENTER  → [Picture]  →   →
 ENTER  → [Custom]  →   →   →   →   →
 ENTER
→ [Tint] →  ,   → ENTER
Adds a natural tone to the display.
 Note
Tint  function can be available just in NTSC system.
Color Tone  MENU →   → ENTER → [Picture] →   →   → ENTER → [Color Tone] →   ,   → ENTERAdjusting the LCD Display 
						

							The color tones can be changed. The individual Color components are also\
 user adjustable.
1.
Off
2. Cool2
3. Cool1
4. Normal
5. Warm1
6. Warm2  Note
If you set the  Color Tone to Cool2,  Cool1, Normal,  Warm1, or  Warm2, the  Color Temp function
is disabled.
Color Temp.  MENU →   → ENTER → [Picture] →   →   →   → ENTER → [Color Temp.] →  ,   → ENTER
Color temp is a measure of the warmth of the image colors.
 Note
This function is only enabled if the  Color Tone is set to Off.
Size  MENU →   → ENTER → [Picture] →   →   →   →   → ENTER → [Size] →   ,   → ENTER
The Size can be switched.
1.
16:9 - Sets the picture to 16:9 wide mode.
2. Zoom 1 - Magnifies the size of the picture on the screen.
3. Zoom 2 - Magnifies the size of the picture more than “ Zoom 1”.
4. 4:3 - Sets the picture to 4:3 normal mode.
5. Just Scan  - Displays the input scenes as they are without any cutoff when HDMI 72\
0p, 1080i,
1080p signals are input. Adjusting the LCD Display 
						

							 Note
Certain external devices may feed the display an out of spec signal that\
 may cause cutoff even when
using the Just Scan feature.
ZOOM1, ZOOM2 will be unavailabel in  HDMI mode.
Digital NR (Digital Noise Reduction)  MENU 
→   →
 ENTER  → [Picture]  →   →   →   →   →   →
 ENTER  → [Digital NR ] →   , 
→ ENTER
Turns the Digital Noise Reduction feature 
Off/On. The Digital Noise Reduction feature allows you to
enjoy clearer and crisper images.
1. Off
2. On
Film Mode  MENU 
→   →
 ENTER  → [Picture]  →   →   →   →   →   →   →
 ENTER  → [Film Mode  ] →  ,   → ENTER
Turns Film Mode Off/On.
The Film Mode feature offers you a theater-quality viewing experience.
(In 
HDMI mode, this function can be available when the input signal is interlace\
d scan; it cannot be
available with progressive scan signal.)
1. Off
2. On
Dynamic Contrast  MENU 
→   →
 ENTER → [ Picture] →   →   →   →   →   →   →   →
 ENTER → [ Dynamic
Contrast ] Adjusting the LCD Display 
						

							→   ,   → ENTER
Dynamic Contrast automatically detects the distribution of the visual signal and adjusts\
 to create an
optimum contrast.
1. Off
2. On
Sound
Available Modes
•  PC / BNC / DVI
•  AV
•  HDMI
•  Component
 Note
• The TV menu is available when a TV tuner box is installed.
• The MagicInfo menu is available when a network box is installed.
Mode  MENU →   →   → ENTER → [Sound] → ENTER → [Mode] →   ,   → ENTER
The LCD Display has a built-in high fidelity stereo amplifier.
1.
Standard
Selects Standard for the standard factory settings.
2. Music Adjusting the LCD Display 
						

							Selects Music when watching music videos or concerts.
3. Movie
Selects Movie when viewing movies.
4. Speech
Selects Speech when watching a show that is mostly dialogue (i.e., news).
5. Custom
Selects Custom if you want to adjust the settings according to your personal preferenc\
es.
Custom  The sound settings can be adjusted to suit your personal preferences.
MENU → 
 →   → ENTER → [Sound] →   → ENTER → [Custom ]
 Note
• You can hear the sound even when sound value is set to 0.
• If you adjust sound using Custom function,  Mode
 will turn to Custom mode.
Bass MENU →   →   →
 ENTER  → [Sound]  →   →
 ENTER  → [Custom  ] → ENTER  → [Bass]  →  ,
 → ENTER
Emphasizes low frequency audio.
Treble MENU →   →   → ENTER → [Sound] →   → ENTER → [Custom ] →   → ENTER →
[Treble] →  ,   ℜ→ ENTER
Emphasizes high frequency audio.
Balance MENU →   →   → ENTER → [Sound] →   → ENTER → [Custom ] →   →   → ENTER →
Balance] →  ,   → ENTER
Allows you to Adjusts the sound balance between the left and right speak\
ers.
Auto Volume  MENU →   →   → ENTER → [Sound] →   →   → ENTER → [Auto Volume] →   ,   → ENTER
Adjusting the LCD Display 
						

							Reduces the difference in volume control between broadcasters.
1.
Off
2. On
SRS TS XT  MENU →   →   → ENTER → [Sound] →   →   →   → ENTER → [SRS TS XT] →   ,   →
ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 mul\
tichannel content
over two speakers. TruSurround delivers a compelling, virtual surround s\
ound experience through any
two-speaker playback system, including internal television speakers. It \
is fully compatible with all
multichannel formats.
1.
Off
2. On  Note
The direct button on the remote control is the SRS button.
Setup
Available Modes
•  PC / BNC / DVI
•  AV
•  HDMI
•  ComponentAdjusting the LCD Display