Samsung SyncMaster 320MP-2 LCD Monitor User Manual

							MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the O\
SD menu
or return to the previous menu.
Navigate buttons (Up-Down buttons)
Moves from one menu item to another vertically or adjusts selected menu \
values.
Adjust buttons (Left-Right buttons) / Volume buttons
Moves from one menu item to another horizontally or adjusts selected men\
u val-
ues. When OSD is not on the screen, push the button to adjust volume.
ENTER button [ENTER]
Activates a highlighted menu item.
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed\
 for
external devices that are connected to the LCD Display at the time.
[PC] → [
DVI] → [ AV] → [HDMI] → [ BNC] → [Component]  Note
• The TV menu is available when a TV tuner box is installed.
• The MagicInfo menu is available when a network box is installed. D.MENU
Opens the on-screen D.MENU.
 Note
• This is available when a TV tuner box is installed. Power button [ ]
Use this button for turning the LCD Display on and off. Power indicator
Shows PowerSaver mode by blinking green
 Note
See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your LCD Display OFF whe\
n it
is not needed or when leaving it unattended for long periods. Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Rear
 Note
For detailed information concerning cable connections, refer to Connecti\
ng Cables under Setup. The
LCD Display s configuration at the back may vary slightly depending on \
the LCD Display model. Introduction 
						

							 POWER S/W ON [ │ ] / OFF [O]
Switches the LCD Display On/Off.  POWER IN
The power cord plugs into the LCD Display and
the wall plug.  
 RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port  DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO
IN] (PC/DVI/HDMI Audio Connection Terminal
(Input))  DVI / PC / HDMI IN [HDMI]
Connect the HDMI terminal at the back of your
LCD Display to the HDMI terminal of your dig-
ital output device using a HDMI cable.  DVI / PC / HDMI IN [RGB](PC Video Con-
nection Terminal)
Using a D-Sub Cable (15 pin D-Sub) - PC mode
(Analog PC)  DVI / PC / HDMI IN [DVI] (PC Video Con-
nection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)
Introduction 
						

							 
 
 DC OUT [5V/1.5A]
Connect this to the  POWER connector of a TV
tuner box or network box.
Make sure to use connecting DC-OUT terminal
to the authorized TV-Tuner Box[SBB-DT*].  Otherwise, this may result in damage to the prod-
uct.
 AV IN [VIDEO] (VIDEO Connection Termi-
nal)
Connect the [ VIDEO ] terminal of your monitor
to the video output terminal of the external device
using a VIDEO cable.  AV AUDIO IN [L-AUDIO-R](LCD Display
Audio Connection Terminal (Input))  AV AUDIO OUT [L-AUDIO-R] (LCD Dis-
play Audio Connection Terminal (Output))  
 BNC/COMPONENT OUT[R/PR, G/Y, B/PB,
H, V]
(BNC/Component Connection Terminal (Out-
put))
BNC (Analog PC) Connection: connecting the R,
G, B, H, V ports.
Component Connection: connecting the PR, Y,
PB ports.  BNC/COMPONENT IN[R/PR, G/Y, B/PB, H,
V]
(BNC/Component Connection Terminal (Input))  Introduction 
						

							Kensington Lock
The Kensington Lock is a device used to physi-
cally fix the system when using it in a public
place. The locking device has to be purchased
separately. The appearance and locking method
may differ from the illustration depending on the
manufacturer. Refer to the manual provided with
the Kensington Lock for proper use. The locking
device has to be purchased separately.
 Note
The location of the Kensington Lock may be dif-
ferent depending on its model.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington
slot on the Monitor  and turn it in the
locking direction  .
2. Connect the Kensington Lock cable.
3. Fix the Kensington Lock to a desk or a heavy
stationary object.  Note
See Connecting Cables for further information regarding cable connections.
Remote Control  Note
The performance of the remote control may be affected by a TV or other e\
lectronic device operating
near the LCD Display , causing a malfunction due to interference with th\
e frequency. Introduction 
						

							 POWER
OFF
Number Buttons
DEL   button
+ VOL -
 MUTE
TV/DTV
 MENU
 INFO
COLOR BUTTONS
 TTX/MIX
STILL
AUTO
S.MODE
MDC
LOCK
 SOURCE
 ENTER/PRE-CH
 CH/P 
D.MENU
GUIDE
 RETURN
Up-Down Left-Right buttons
 EXIT
 SRS
MagicInfo
P.MODE
 DUAL/MTS
PIP
SWAP
1.   POWER
Turns the product On.
2.   Off
Turns the product Off.
3. Number Buttons Press to change the channel.Introduction 
						

							4. DEL   button
The - button operates only for DTV. It is used to select MMS
(multi-channel) for a DTV.
5. + VOL - Adjusts the audio volume.
6.  MUTE
Pauses (mutes) the audio output temporarily. This is displayed on
the lower left corner of the screen. The audio resumes if MUTE
or - VOL + is pressed in the Mute mode.
7. TV/DTV Selects the TV and DTV mode directly.
8.  MENU
Opens the on-screen menu and exits from the menu or closes the
adjustment menu.
9. Activates a highlighted menu item.
10.  INFO
Current picture information is displayed on the upper left corner
of the screen.
11.COLOR BUTTONS Press to add or delete channels and to store channels to the favorite
channel list in the “Channel List” menu.
12.  TTX/MIX
TV channels provide written information services via teletext.
- Teletext Buttons For more information > TTX / MIX
13.STILL Press the button once to freeze the screen. Press it again to un-
freeze.
14.AUTO Adjusts the screen display automatically in  PC mode. By changing
the resolution in the control panel, auto function is performed.
15. S.MODE When pressing this button, the current mode is displayed at the
bottom centre of the screen. The LCD Display has a built-in high
fidelity stereo amplifier. Then press the button again to circle
through available preconfigured modes. (  Standard → Music →
Movie → Speech → Custom )
16.MDC MDC Quick Launch Button.
17.LOCK Activates or deactivates all function keys on both the remote con-
trol and the LCD Display except for the Power and LOCK buttons.
18.  SOURCE
Press the button to change the input signal SOURCE.
Changing the SOURCE is only allowed for external devices that
are connected to the monitor at the time.
19.  ENTER/PRE-CH
This button is used to return to the immediately previous channel.
20. CH/P In TV mode, selects TV channels.
21.D.MENU DTV menu display
22.GUIDE Electronic Program Guide (EPG) display.
23.  RETURN
Returns to the previous menu.Introduction 
						

							24. Up-Down Left-Right but-
tons
Moves from one menu item to another horizontally, vertically or
adjusts selected menu values.
25.  EXIT
Exits from the menu screen.
26.  SRS
Selects SRS TruSurround XT mode.
27.MagicInfo MagicInfo Quick Launch Button.
28. P.MODE When you press this button, current picture mode is displayed on
the lower center of the screen.
AV
 / HDMI
 / TV
 : P.MODE
The LCD Display has four automatic picture settings that are pre-
set at the factory. Then push button again to circle through avail-
able preconfigured modes. (  Dynamic → Standard → Movie →
Custom )
PC / DVI / MagicInfo: M/B (MagicBright)
MagicBright is a feature providing the optimum viewing envi-
ronment depending on the contents of the image you are watching.
Then push button again to circle through available preconfigured
modes. (Entertain → Internet → Text  → Custom )
29.  DUAL/MTS
DUAL-
STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote control
while watching TV.
MTS-
You can select MTS (Multichannel Television Stereo) mode.
Audio Type MTS/S_Mode Default
FM Stereo Mono Mono Manual Change
Stereo Mono ↔ Stereo
SAP Mono ↔ SAP Mono
30. PIP Every time you press the button, a PIP screen appears.
- This fuction does not work for this LCD Display.
31.SWAP Swaps the contents of the PIP and main image. The image in the
PIP window will appear on the main screen, and the main screen
image will appear in the PIP window.
- This fuction does not work for this LCD Display.
Mechanical Layout
Mechanical Layout Introduction 
						

							Installation VESA Bracket
• When installing VESA, make sure to comply with the international VESA st\
andards.
•Purchasing VESA Bracket and Installation Information : Please contact yo\
ur nearest SAMSUNG
Distributor to place an order. After your order is placed, installation \
professionals will visit you
and install the bracket.
• At least 2 persons are needed in order to move the LCD Display.
• SAMSUNG is not responsible for any product damage or any injury caused b\
y installation at
customers discretion.
Dimensions Notice
For securing the bracket on a wall, use only machine screws of 6 mm diam\
eter and 8 to 12 mm length. Introduction 
						

							Wall Bracket Installation
• Contact a technician for installing the wall bracket.
•SAMSUNG Electronics is not responsible for any damages to the product or\
 harm to customers
when the installation is done by the customer.
• This product is for installing on cement walls. The product may not stay\
 in place when installed
on plaster or wood.
Components Only use the components and accessories shipped with the product. Wall Bracket(1)
Hinge(Left 1, Right
1)Plastic
Hanger
(4)Screw
(A)(11)
Screw(B)
(4)Anchor
(11)
Wall Bracket Assembly  Note
There are two hinges(left and right). Use the correct one.
1. Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one.
A - Captive Screw
B - Wall Bracket
C - Hinge (Left)
D - Hinge (Right)Introduction 
						

							2.
Before drilling into the wall, check if the length between the two locki\
ng holes at the back of the
product is correct.
If the length is too short or long, loosen all or some of the 4screws on\
 the wall bracket to adjust
the length. A -
Length between the two locking holes
3. Check the installation diagram and mark the drill points on the wall. Us\
e the 5.0 mm bit to drill
holes deeper than 35 mm. Fix each anchor in the corresponding hole. Matc\
h each of the brackets
and hinge holes to the corresponding anchor holes and insert and tighten\
 the 11 screws A. To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assembli\
es of the plastic hanger and
the screw are the same)
1. Remove the 4 screws on the back of the product. Introduction