Samsung Syncmaster 2243sw User Manual

							 Note
This monitor  driver 
is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual) Microsoft®
 Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2. Click  (Start) and "Control Panel". Then, double-click on "Appearance and Personal-
ization". 3. Click "Personalization" and then "Display Settings".
4. Click "Advanced Settings...".
 
5. Click  "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means
the configuration for your monitor is completed. The monitor can be used as is. Using the Software
30
Downloaded from ManualMonitor.com Manual± 
						

							If  the  message  "Windows  needs..."  is  displayed,  as  shown  in  the  figure  below,  click
"Continue".
 Note
This monitor  driver 
is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click "Update Driver..." in the "Driver" tab. 7. Check  the 
"Browse 
 my  computer  for  driver  software"  checkbox  and  click  "Let  me  pick
from a list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup
file is located, and click "OK". Using the Software
31
Downloaded from ManualMonitor.com Manual± 
						

							9. Select the model that matches your monitor from the list of monitor models on the screen,
and click "Next".  
10. Click "Close"  →  "Close" → "OK"  → "OK" on the following screens displayed in sequence. Microsoft
®
 Windows ®
 XP Operating System Using the Software
32
Downloaded from ManualMonitor.com Manual± 
						

							1. Insert CD into the CD-ROM drive.
2.
Click "Start"  → "Control Panel" then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
6. Select "Don't search, I will..." then click "Next" and then click "Have disk". Using the Software
33Downloaded from ManualMonitor.com Manual± 
						

							7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in
the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then
click "OK" button.  
 Note
This monitor  driver 
is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9. Click the "Close" button then click "OK" button continually. Using the Software
34
Downloaded from ManualMonitor.com Manual± 
						

							 
10. Monitor driver installation is completed.
Microsoft ®
 Windows ®
 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3.
Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1. Click "Start", "Setting", "Control Panel".
2. Double click the "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
4. Choose "Monitor". Case1 : If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2 : If the "Properties" button is active, click the "Properties" button then follow next
steps continually.
5. Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver).
8. Click the "Open" button, then click "OK" button.
9. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And
click the "Finish" button then the "Close" button.
Microsoft ®
 Windows ®
 Millennium Operating System
1. Click "Start", "Setting", "Control Panel".
2. Double click the "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button. Using the Software
35
Downloaded from ManualMonitor.com Manual± 
						

							4. Select the "Monitor" tab.
5.
Click the "Change" button in the "Monitor Type" area.
6. Choose "Specify the location of the driver".
7.
Choose "Display a list of all the driver in a specific location..." then click "Next" button.
8. Click the "Have Disk" button.
9. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you con- nected to your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft ®
 Windows ®
 NT Operating System
1. Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
2. In Display Registration Information window, click Settings Tab and then click "All Display Modes".
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK".
4. Click  "Apply"  button  if  you  see  the  screen  working  normally  after  clicking  "Test".  If  the screen  is  not  normal,  change  to  a  different  mode  (lower  mode  of  resolution,  colors  or
frequency).  Note
If there  is 

no Mode at All Display Modes, select the level of resolution and vertical frequency
by referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting
file.
1. Press "Enter" at the first and the second screen after executing the X86Config file.
2. The third screen is for setting your mouse.
3. Set a mouse for your computer.
4. The next screen is for selecting a keyboard.
5. Set a Keyboard for your computer.
6. The next screen is for setting your monitor.
7. First  of  all,  set  a  horizontal  frequency  for  your  monitor.  (You  can  enter  the  frequency directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. Using the Software
36
Downloaded from ManualMonitor.com Manual± 
						

							10. You 
have  finished  setting  up  your  monitor.  Execute  X-Window  after  setting  other  re-
quested hardware.
Natural Color
Natural Color Software Program One of the recent problems in using a computer is that the color of the images printed out by
a 
printer  or 
other images scanned by a scanner or a digital camera are not the same as those
shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color
administration  system  developed  by  Samsung  Electronics  in  association  with  Korea  Elec-
tronics  &  Telecommunications  Research  Institute  (ETRI).  This  system  is  available  only  for
Samsung monitors and makes the color of the images on the monitor the same as the printed
or scanned images. For more information, refer to Help (F1) in the software program.
How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial
screen of the program Natural Color will be executed. Click Natural Color on the initial screen
to install the Natural Color software.
To install the program manually, insert the CD included with the Samsung monitor into the
CD-ROM  Drive,  click  the  [Start]  button  of  Windows  and  then  select  [Run...].  Enter  D:\color
\NCProSetup.exe and then press the [Enter] key. (If the drive where the CD is inserted is not
D:\, enter the applicable drive.)
How to delete the Natural Color software program Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a pro-
gram". Select Natural Color from the list and then click the "Add/Delete" button. Using the Software
37
Downloaded from ManualMonitor.com Manual± 
						

							MagicTune™
Installation
1. Insert the installation CD into the CD-ROM drive.
2.Click the MagicTune™ installation file.  Note
If the  popup 
window to install the software for the main screen is not displayed, proceed
with the installation using the MagicTune executable file on the CD.
3. Select installation Language, Click "Next".
4. When the Installation Shield Wizard window appears, click "Next".
5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune™ program.
7. Click "Install".
8. The "Installation Status" window appears.
9. Click "Finish".
10. When  the  installation  is  complete,  the  MagicTune™  executable  icon  appears  on  your desktop. Double-click the icon to start the program.
MagicTune™ execution icon may not appear depending on specification of com-
puter system or monitor. If that happens, press F5 Key. Installation Problems
The installation  of 

MagicTune™ can be affected by such factors as the video card, mother-
board and the network environment.
System Requirements
OS
• Windows 2000
• Windows XP Home Edition
• Windows XP Professional
• Windows Vista™It is recommended using MagicTune™ in Windows ®
 2000 or later. Using the Software
38
Downloaded from ManualMonitor.com Manual± 
						

							Hardware
• 32 MB Memory above
•
60 MB Hard disk space above
For more information, visit the MagicTune™ 
website.Uninstall
The MagicTune™  program 

can be removed only by using the "Add or Remove Programs"
option of the Windows ®
 Control Panel.
Perform the following steps remove MagicTune™.
1. Go to [Task Tray]  → [Start] → [Settings] and select [Control Panel] in the menu. If the
program runs on Windows ®
 XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add or Remove Programs" icon in Control Panel.
3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears.  Note
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and
answers) and software upgrades. MagicRotation
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicRotation installation file. Using the Software
39
Downloaded from ManualMonitor.com Manual±