Samsung Syncmaster 2243sw User Manual

							Cables
D-Sub Cable
Power CordDVI Cable (option)
Others  
 
Cleaning Cloth     Note
Cleaning Cloth is only provided for highly polished black products as a product feature.
{943SW/943SWX} Your Monitor
Initial Settings Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can 
be 
displayed up to three (3) times. Make sure to adjust the resolution of your PC before
reaching the maximum count.  Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product. Introduction
10
Downloaded from ManualMonitor.com Manual± 
						

							FrontMENU button [MENU/]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
Customized Key[
]
You  can  customize 
key  assignment  for  the  Custom  button  according  to
your preferences.  Note
You can  configure 

the customized key for a required function via  Setup >
Customized Key.
Brightness button []
When OSD is not on the screen, push the button to adjust brightness.
>> Click here to see an animation clip
Adjust buttons []
These buttons allow you to adjust items in the menu.
Enter button [] / SOURCE button
Activates a highlighted menu item.
Push the ' /SOURCE', then 
selects 
 the video signal while the OSD is off.
(When  the  /SOURCE  button  is  pressed  to  change  the  input  mode,  a
message  appears 

in  the  upper  left  of  the  screen  displaying  the  current
mode -- analog or digital input signal.) Introduction
11
Downloaded from ManualMonitor.com Manual± 
						

							 Note
If you  select 
the digital mode, you must connect your monitor to the graphic
card's DVI port using the DVI cable.
>> Click here to see an animation clip
AUTO button
Use this button for auto adjustment.
>> Click here to see an animation clip
Power button []
Use this button for turning the product on and off.
Power Indicator
This  light  is  lit  when  operating  normally,  and  blinks  once  when  your  ad-
justments are saved.  Note
See PowerSaver described  in 

the manual for further information regarding
power saving functions. For energy conservation, turn your monitor OFF
when it is not needed or when leaving it unattended for long periods.
Rear  Note
The configuration at the back of the product may vary from product to product. Simple Stand
HAS Stand
POWER port
Connect the power cord for your monitor to the POWER port on the back of
the product.
DVI IN port
Connect the DVI Cable to the DVI IN port on the back of your monitor.
RGB IN port
Introduction 12
Downloaded from ManualMonitor.com Manual± 
						

							Connect the D-sub cable to the 15-pin, RGB IN port on the back of your mon-
itor.Kensington Lock
The Kensington lock is a device used to physically fix the system when using
it in a public place. (The locking device has to be purchased separately.) For
using a locking device, contact where you purchase it.
 Note
The location  of 

the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington slot on the Monitor  and
turn it in the locking direction  .
2. Connect the Kensington Lock cable.
3. Fix the Kensington Lock to a desk or a heavy stationary object.  Note
See  {943SW/943SWX}  Connecting  Cables

  for  further  information  regarding  cable  connec-
tions.
Cable holding ring
• Fix the cables using the holding ring, as shown in the figure.
{2043SW/2043SWX/2243SW/2243SWX} Package Contents  Note
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer  to buy optional items.
Unpacking Type 1 Introduction
13
Downloaded from ManualMonitor.com Manual± 
						

							Monitor & Simple stand
  Note
MagicRotation program  can 
not be provided as Simple Stand does not support Pivot function.
Type2 Monitor & HAS stand
Type3 Monitor & Dual Hinge Stand
Manuals Quick Setup Guide Warranty Card
(Not available in all loca-tions) User's Guide
Introduction
14
Downloaded from ManualMonitor.com Manual± 
						

							Cables
D-Sub Cable
Power CordDVI Cable (option)
Others  
 
Cleaning Cloth     Note
Cleaning Cloth is only provided for highly polished black products as a product feature.
{2043SW/2043SWX/2243SW/2243SWX} Your Monitor
Initial Settings Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can 
be 
displayed up to three (3) times. Make sure to adjust the resolution of your PC before
reaching the maximum count.  Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product. Introduction
15
Downloaded from ManualMonitor.com Manual± 
						

							FrontMENU button [MENU/]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
Customized Key[
]
You  can  customize 
key  assignment  for  the  Custom  button  according  to
your preferences.  Note
You can  configure 

the customized key for a required function via  Setup >
Customized Key.
Brightness button []
When OSD is not on the screen, push the button to adjust brightness.
>> Click here to see an animation clip
Adjust buttons []
These buttons allow you to adjust items in the menu.
Enter button [] / SOURCE button
Activates a highlighted menu item.
Push the ' /SOURCE', then 
selects 
 the video signal while the OSD is off.
(When  the  /SOURCE  button  is  pressed  to  change  the  input  mode,  a
message  appears 

in  the  upper  left  of  the  screen  displaying  the  current
mode -- analog or digital input signal.) Introduction
16
Downloaded from ManualMonitor.com Manual± 
						

							 Note
If you  select 
the digital mode, you must connect your monitor to the graphic
card's DVI port using the DVI cable.
>> Click here to see an animation clip
AUTO button
Use this button for auto adjustment.
>> Click here to see an animation clip
Power button []
Use this button for turning the product on and off.
Power Indicator
This  light  is  lit  when  operating  normally,  and  blinks  once  when  your  ad-
justments are saved.  Note
See PowerSaver described  in 

the manual for further information regarding
power saving functions. For energy conservation, turn your monitor OFF
when it is not needed or when leaving it unattended for long periods.
Rear  Note
The configuration at the back of the product may vary from product to product. Simple Stand
HAS Stand
POWER port
Connect the power cord for your monitor to the POWER port on the back of
the product.
DVI IN port
Connect the DVI Cable to the DVI IN port on the back of your monitor.
RGB IN port
Introduction 17
Downloaded from ManualMonitor.com Manual± 
						

							Connect the D-sub cable to the 15-pin, RGB IN port on the back of your mon-
itor.Kensington Lock
The Kensington lock is a device used to physically fix the system when using
it in a public place. (The locking device has to be purchased separately.) For
using a locking device, contact where you purchase it.
 Note
The location  of 

the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington slot on the Monitor  and
turn it in the locking direction  .
2. Connect the Kensington Lock cable.
3. Fix the Kensington Lock to a desk or a heavy stationary object.  Note
See  {943SW/943SWX}  Connecting  Cables

  for  further  information  regarding  cable  connec-
tions.
Cable holding ring
• Fix the cables using the holding ring, as shown in the figure. Introduction
18
Downloaded from ManualMonitor.com Manual± 
						

							Connections
{943SW/943SWX} Connecting Cables
 Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.  Use a connection appropriate for your computer.
 Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN]
 Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the DVI IN Port on the back of your Monitor. [DVI IN]
 Connected to a Macintosh.
• Connect the monitor to the Macintosh computer using the D-sub connection cable.  Note
If the monitor and the computer are connected, you can turn them on and use them. 19Downloaded from ManualMonitor.com Manual±