Samsung SCX 5530FN User Manual

2.4   
Correcting numbers or names
If you make a mistake while entering a number or name, press the left 
Scroll  button to delete the last digit or character. Then enter the correct 
number or character.
Inserting a pause
With some telephone systems, you must dial an access code (9, for 
example) and listen for a second dial tone. In such cases, you must insert 
a pause in the telephone number. You can insert a pause while you are 
setting up speed buttons or speed dial numbers.
To insert a pause,...

3.1   
3 Software overview
This chapter gives you an overview of the software that comes with your 
machine. Further details about installing and using the software are 
explained in the  Software Section .
This chapter includes:
• Supplied software
• Printer driver features
• System requirements
Supplied software
You must install the printer and scanner software using the supplied CDs 
after you have set up your machine and connected it to your computer. 
Each CD provides you with the following...

3.2   
Printer driver features
Your printer drivers support the following standard features:
• Paper source selection
• Paper size, orientation and media type
• Number of copies
In addition, you can use various special printing features. The following 
table shows a general overview of features supported by your printer 
drivers: 
FeaturePCL 6 PostScript
( SCX-5530FN  only)
Windows Windows Macintosh Linux
Toner save O O
XO
Print quality 
option OOOO
Poster 
printing O
XXX
Multiple 
pages per 
sheet...

3.3   
Linux
Macintosh 
(SCX-5530FN only)
ItemRequirements
Operating system • Red Hat 8.0 ~ 9.0 • Fedora Core 1 ~ 3
• Mandrake 9.2 ~ 10.1
• SuSE 8.2 ~ 9.2
CPU Pentium IV 1 GHz or higher
RAM 256 MB or higher
Free disk space 1 GB or higher
Software • Linux Kernel 2.4 or higher • Glibc 2.2 or higher
• CUPS
• SANE(for MFP device only)
Notes
• It is necessary to claim swap partition of 300 MB or larger for working with large scanned images.
• The Linux scanner driver supports the optical resolution at...

4.1   
4 Network setup
This chapter gives you step-by-step  instructions for setting up your 
machine for network connections.
This chapter includes:
•Introduction
• Supported operating systems
• Configuring TCP/IP
• Configuring EtherTalk
• Configuring I PX frame types
• Setting Ethernet speed
• Restoring the network configuration
• Printing a network configuration page
• Using SetIP program
Introduction
Once you have connected your machine to a network with an RJ-45 
Ethernet cable, you can share the...

4.2   
Static addressing
To enter a TCP/IP address from your machine’s control panel, take the 
following steps: 
1 Press  Menu until Network  appears on the bottom line of the display 
and press 
OK.
2 Press  OK when  TCP/IP  appears.
3 Press the  Scroll buttons until  Static appears and press  OK.
4 Press  OK when  IP Address  appears. 
5 Enter a byte between 0 and 255 using the number keypad and 
press the  Scroll buttons to move between bytes.
Repeat this to complete the address from the 1st byte to...

4.3   
Setting Ethernet speed
You can select the communication speed for Ethernet connections.
1 Press  Menu until Network  appears on the bottom line of the display 
and press  OK.
2 Press the  Scroll buttons until  Ethernet Speed  appears and press 
OK .
3 Press the  Scroll buttons until the speed you want appears and 
press  OK.
4 Press 
Stop/Clear to return to Standby mode.
Restoring the network configuration
You can return the network configuration to its default settings.
1Press  Menu until...

5.1   
5 Loading originals and print 
media
This chapter introduces you to how to load originals and print media into 
your machine.
This chapter includes:
• Loading originals
• Selecting print media
• Loading paper
• Setting the paper size and type
• Selecting an output location
Loading originals
You can use the scanner glass or ADF to load an original for copying, 
scanning, and sending a fax.
On the scanner glass
Make sure that no originals are in the ADF. If an original is detected in the 
ADF, the...

5.2   
To load an original into the ADF:
1 Load the original face up into the ADF. Make sure that the bottom of 
the original stack matches the paper size marked on the document 
input tray.
2 Adjust the document width guides to the paper size.
Note 
Dust on the ADF glass may cause black lines on the printout. 
Always keep it clean.
Selecting print media
You can print on a variety of print media, such as plain paper, envelopes, 
labels, and transparencies. Always use print media that meet the...

5.3   
Supported print media types and sizes
Ty p eSizeDimensionsWeight1
1. If media weight is over 90 g/m2 ( 24 lb bond), use the multi-purpose tray.
Capacity2
2. Maximum capacity may differ depending on medi a weight, thickness, and environmental conditions.
Plain paper Letter 216 x 279 mm (8.5 x 11 inches) • 60 to 90 g/m2 (16 to 24 lb 
bond) for the tray
• 60 to 163 g/m
2 (16 to 43 lb 
bond) for the multi-purpose 
tray • 250 sheets of 75 g/m
2 
(20 lb bond) paper for the 
tray
• 50 sheets for the...