Samsung SCX 4725FN User Manual
Have a look at the manual Samsung SCX 4725FN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
13.13 Common Linux problems ProblemPossible cause and solutions The machine does not print. • Check if the printer driver is installed in your system. Open Unified Driver configurator and switch to the Printers tab in Printers configuration window to look at the list of available printers. Make sure that your machine is displayed on the list. If not, please, invoke Add new printer wizard to set up your device. • Check if the printer has started. Open Printers configuration and select your machine on the printers list. Look at the description in the Selected printer pane. If its status contains “(stopped)” string, please, press the Start button. After that normal operation of the printer should be restored. The “stopped” status might be activated when some problems in printing occurred. For instance, this could be an attempt to print a document when a port is claimed by a scanning application. • Check if the port is not busy. Since functional components of MFP (printer and scanner) share the same I/O interface (port), the situation of simultaneous access of different “consumer” applications to the same port are possible. To avoid possible conflicts, only one of them at a time is allowed to gain control over the device. The other “consumer” will encounter “device busy” response. You should open ports configuration and select the port assigned to your printer. In the Selected port pane you can see if the port is occupied by some other application. If this is the case, you should wait for completion of the current job or should press Release port button, if you are sure that the present owner is not functioning properly. • Check if your application has special print option such as “-oraw”. If “-oraw” is specified in the command line parameter then remove it to print properly. For Gimp front-end, select “print” -> “Setup printer” and edit command line parameter in the command item. • The CUPS (Common Unix Printing System) version distributed with SuSE Linux 9.2 (cups-1.1.21) has a problem with ipp (Internet Printing Protocol) printing. Use the socket printing instead of ipp or install later version of CUPS (cups-1.1.22 or higher).The machine does not appear on the scanners list. • Check if your machine is attached to your computer. Make sure that it is connected properly via the USB port and is turned on. • Check if the scanner driver for your machine is installed in your system. Open Unified Driver configurator, switch to Scanners configuration, then press Drivers . Make sure that driver with a name corresponding to your machines name is listed in the window. Check if the port is not busy. Since functional components of MFP (printer and scanner) share the same I/O interface (port), the situation of simultaneous access of different “consumer” application to the same port is possible. To avoid possible conflicts, only one of them at a time is allowed to gain control over the device. The other “consumer” will encounter “device busy” response. This can usually happen while starting scan procedure, and appropriate message box appears. • To identify the source of the problem, you should open ports configuration and select the port assigned to your scanner. ports symbol /dev/mfp0 corresponds to LP:0 designation displayed in the scanners’ options, /dev/mfp1 relates to LP:1 and so on. USB ports start at /dev/mfp4, so scanner on USB:0 relates to /dev/mfp4 respectively and so forth sequentially. In the Selected port pane you can see if the port is occupied by some other application. If this is the case, you should wait for completion of the current job or you should press Release port button, if you are sure that the present ports owner is not functioning properly. The printer does not print PDF file correctly. Some parts of graphics, text or illustrations are missing. Incompatibility between the PDF file and the Acrobat products: Printing the PDF file as an image may solve this problem. Turn on Print as Image from the Acrobat printing options. Note: It will take longer to print when you print a PDF file as an image. ProblemPossible cause and solutions Downloaded From ManualsPrinter.com Manuals
13.14 The machine does not scan. • Check if a document is loaded into the machine. • Check if your machine is connected to the computer. Make sure if it is connected properly if an I/O error is reported while scanning. • Check if the port is not busy. Since functional components of MFP (printer and scanner) share the same I/O interface (port), the situation of simultaneous access of different “consumer” application to the same port is possible. To avoid possible conflicts, only one of them at a time is allowed to gain control over the device. The other “consumer” will encounter “device busy” response. This can usually happen while starting scan procedure, and appropriate message box will be displayed. To identify the source of the problem, you should open ports configuration and select the port assigned to your scanner. port’s symbol /dev/mfp0 corresponds to LP:0 designation displayed in the scanners’ options, /dev/mfp1 relates to LP:1 and so on. USB ports start at /dev/mfp4, so scanner on USB:0 relates to /dev/mfp4 respectively and so forth sequentially. In the Selected port pane you can see if the port is occupied by some other application. If this is the case, you should wait for completion of the current job or should press the Release port button, if you are sure that the present port’s owner is not functioning properly. I cannot scan via Gimp Front-end. • Check if Gimp Front-end has “Xsane: Device dialog.” on the “Acquire” menu. If not, you should install Xsane plug- in for Gimp on the your computer. You can find Xsane plug-in package for Gimp on Linux distribution CD or Gimp home page. For the detail information, refer to the Help for Linux distribution CD or Gimp Front-end application. If you wish to use other kind of scan application, refer to the Help for application. ProblemPossible cause and solutions Common Macintosh problems (SCX-4725FN only) I encounter error “Cannot open port device file” when printing a document.Please avoid changing the print job parameters (via LPR GUI, for example) while a print job is in progress. Known versions of CUPS server break the print job whenever print options are changed and then try to restart the job from the beginning. Since Unified Linux Driver locks port while printing, the abrupt termination of the driver keeps the port locked and therefore unavailable for subsequent print jobs. If this situation occurred, please, try to release the port. ProblemSuggested solutions The printer does not print PDF file correctly. Some parts of graphics, text or illustrations are missing. Incompatibility between the PDF file and the Acrobat products: Printing the PDF file as an image may solve this problem. Turn on Print as Image from the Acrobat printing options. Note: It will take longer to print when you print a PDF file as an image. The document has printed, but the print job has not disappeared from the spooler in Mac OS 10.3.2. Update your Mac OS to OS 10.3.3. or higher. Some letters are not displayed normally during the Cover page printing. This problem is caused because Mac OS can not create the font during the Cover page printing. English alphabet and numbers are displayed normally at the Cover page. ProblemPossible cause and solutions Downloaded From ManualsPrinter.com Manuals
14.1 14 Specifications This chapter includes: • General specifications • Printer specifications • Scanner and copier specifications • Facsimile specifications General specifications ItemDescription ADF Up to 30 sheets (75 g/m2) ADF document size Width: 142 to 216 mm Length: 148 to 356 mm Paper input capacity Tray: 250 multi-pages for plain paper (75 g/m2) Manual tray: 1 sheet of paper (60 to 165 g/m 2) Paper output capacity Output tray: 100 sheets (face down) Consumables 1-piece toner cartridge system Power rating 110 - 127 VAC, 50/60 Hz, 5.5 A 220 - 240 VAC, 50/60 Hz, 3 A Power consumption Average: Less than 400 W Power save mode: Less than 13.5 W Noise level 1Standby mode: Less than 35 dBA Printing: Less than 53 dBA Copying mode: Less than 55 dBA Warm up: Less than 49 dBA Warm-up time Less than 30 seconds (from sleep mode) Operating environment Temperature: 10 °C to 32 °C Humidity: 20% to 80% RH Display 16 characters x 2 lines Toner cartridge yield 21,500 or 3,000 pages. Memory 32 MB External dimension (W x D x H) 17.2 X 14.7 X 15.2 inches (438 x 374 x 387 mm) Printer specifications Weight (including consumables) 11 . 2 K g Package weight Paper: 1.3 Kg, Plastic: 0.5 Kg Duty cycle Monthly print: Up to 10,000 pages 1. Sound Pressure Level, ISO 7779 2. Average cartridge yield declared in accordance with ISO/IEC 19752. The number of pages may be affected by operating environment, printing interval, media type, and media size. ItemDescription Printing method Laser Beam Printing Printing speed 1 1. Print speed will be affected by operating system used, computing performance, application software, connecting method, media type, media size, and job complexity. Up to 24 ppm in A4 (24 ppm in Letter) First print out time 10 seconds (from ready) Print resolution Up to 1,200 x 1,200 dpi effective output Printer language PCL 6, PS 3 (SCX-4725FN only), SPL (for Linux only) OS Compatibility 2 2. Please visit www.samsungprinter.com to download the latest software version. Windows 98/Me/2000/XP(32/64bit)/ 2003(32/64bit) Various Linux OS Macintosh 10.3 ~ 10.4 (SCX-4725FN only) Interface High Speed USB 2.0 Ethernet 10/100 Base TX (SCX-4725FN only) ItemDescription Downloaded From ManualsPrinter.com Manuals
14.2 Scanner and copier specifications ItemDescription Compatibility TWAIN standard/WIA standard Scanning method ADF and Flat-bed Color CIS (Contact Image Sensor) module Resolution Optical: 600 x 600 dpi (mono and color) Enhanced: 4,800 x 4,800 dpi Effective scanning length Scanner glass: 297 mm ADF: 356 mm Effective scanning width Max 208 mm Color bit depth 24 bit Mono bit depth 1 bit for Black & White mode 8 bit for Gray mode Copy speed 1 1. Copy Speed is based on Single Document Multiple Copy. Up to 24 ppm in A4 (24 ppm in Letter) Copy resolution Scan: up to 600 x 300 (text, text/photo) up to 600 x 600 (photo using platen) up to 600 x 300 (photo using ADF) Print: up to 600 x 600 (text, text/photo, photo) Zoom rate Scanner glass: 25 to 400% ADF: 25 to 100% Multiple copies 1 to 99 pages Grayscale 256 levels Facsimile specifications ItemDescription Compatibility ITU-T Group 3 Applicable line Public Switched Telephone Network (PSTN) or behind PABX Data coding MH/MR/MMR/JBIG/JPEG/ECM (Error Correction Mode) Modem speed 33.6 Kbps Transmission speed Approx. 3 seconds/page1 1. Transmission time applies to memory transmission of text data with ECM compression using only ITU-T No.1 Chart. Maximum document lengthScanner glass: 297 mm Automatic document glass: 356 mm Resolution Standard: 203 x 98 dpi Fine: 203 x 196 dpi Super Fine: 300 x 300 dpi Photo: 203 x 196 dpi Color: 200 x 200 dpi Memory 4 MB Halftone 256 levels Auto dialer Group dialing (up to 200 numbers) Downloaded From ManualsPrinter.com Manuals
1 INDEX Numerics 2/4-up, special copy 6.3 A accessories, order information 11.1 ADF 1.2 ADF rubber pad, replace 12.6 ADF, load 5.1 alarm sound 2.3 Ans/Fax mode, receiving mode 9.4 auto fit, special copy 6.3 B broadcast faxes 9.6 C characters, enter 2.3 cleaning drum 12.5 inside 12.2 LSU 12.3 outside 12.2 scan unit 12.3 clock mode 2.2 clone, special copy 6.2 collation, special copy 6.2 component location 1.2 control panel 1.3 copying 2/4-up 6.3 auto fit 6.3 clone 6.2 collation 6.2, 6.3 default setting, change 6.2 ID card copy 6.3 poster 6.4 time out, set 6.4 D date and time, set 2.2 delayed fax 9.6 display language, change 2.2 DRPD (Distinctive Ring Pattern Detection) mode, receiving mode 9.4 drum, clean automatically 12.5 manually 12.5 E error messages 13.3 F fax header, set 9.1 Fax mode, receiving mode 9.3 fax number, set 9.1 faxing broadcast faxes 9.6 delayed faxes 9.6 fax setup 10.1 original settings 9.1 priority faxes 9.7 receiving faxes 9.3 sending faxes 9.2 G Group dial numbers, set 10.3 H high altitude 13.10 I ID card, special copy 6.3 J jam, clear document 13.1 paper 13.1 K key sound 2.3 L Linux problems 13.13 loading originals ADF 5.1 scanner glass 5.1 loading paper manual tray 5.6 tray 5.5 M machine ID, set 9.1 Macintosh problems 13.14 manual tray, load paper 5.6 memory, clear 12.1 N network configuration print 4.2 restore 4.2 network interface, reset 4.2 network setup EtherTalk 4.2 operating systems 4.1 TCP/IP 4.1 new toner notification, send 12.5 n-up (multiple pages per sheet) copying 6.3 Downloaded From ManualsPrinter.com Manuals
2 O originalsjam, clear 13.1 loading 5.1 output location 5.7 output tray 5.7 P paper guidelines 5.4 paper jam, clear fuser area or around toner cartridge 13.2 manual tray 13.2 paper exit area 13.2 tray 13.2 paper load manual tray 5.6 tray 5.5 paper size setting 5.7 specifications 5.3 paper type setting 5.7 specifications 5.3 Phone Book group dial numbers 10.3 speed dial numbers 10.3 poster, special copy 6.4 PostScript problems 13.12 power save mode 2.4 print quality problems, solve 13.8 printing network configuration page 4.2 reports 12.1 priority fax 9.7 problem, solve copying 13.10 error messages 13.3 faxing 13.11 Linux 13.13 Macintosh 13.14 paper feeding 13.5 PostScript errors 13.12 printing 13.6 printing quality 13.8 scanning 13.11 Windows 13.12 R receiving a fax in Ans/Fax mode 9.4 in DRPD mode 9.4 in Fax mode 9.3 in Secure Receiving mode 9.4 in Tel mode 9.3 receiving modes, change 9.3 redialing automatically 9.3 manually 9.3 replacement parts 12.6 replacing ADF rubber pad 12.6 toner cartridge 12.4 reports, print 12.1 ringer 2.3 S scan power save mode 2.4 scanner glass cleaning 12.3 loading documents 5.1 scanning, to application 8.1 secure receiving mode 9.4 sending a fax automatically 9.2 manually 9.2 sounds, set 2.2 speaker sound 2.3 speaker volume 2.3 special copy features 6.2 special print media, guidelines 5.4 specifications facsimile 14.2 general 14.1 paper 5.3 printer 14.1 scanner and copier 14.2 speed dial numbers, set 10.3 supplies, order information 11.1 system requirements Linux 3.3 Macintosh 3.3 Windows 3.2 T Tel mode, receiving mode 9.3 toll save mode, use 10.2 toner cartridge cleaning 12.5 maintaining 12.3 redistributing 12.4 replacing 12.4 toner save mode, use 2.3 tray, load paper 5.5 V volume, adjust ringer 2.3 speaker 2.3 W Windows problems 13.12 Downloaded From ManualsPrinter.com Manuals
Samsung Printer Software section Downloaded From ManualsPrinter.com Manuals
1 SOFTWARE SECTION C ONTENTS Chapter 1: INSTALLING PRINTER SOFTWARE IN WINDOWS Installing Printer Software ........................................................................................................ 4 Installing Software for Local Printing ................................................................................. 4 Installing Software for Network Printing ............................................................................. 7 Reinstalling Printer Software ................................................................................................... 10 Removing Printer Software ..................................................................................................... 11 Chapter 2: BASIC PRINTING Printing a Document .............................................................................................................. 12 Printing to a file (PRN) .......................................................................................................... 12 Printer Settings ..................................................................................................................... 13 Layout Tab .................................................................................................................. 13 Paper Tab .................................................................................................................... 14 Graphics Tab ............................................................................................................... 15 Extras Tab ................................................................................................................... 16 About Tab ................................................................................................................... 16 Printer Tab .................................................................................................................. 16 Using a Favorite Setting ................................................................................................ 17 Using Help ................................................................................................................... 17 Chapter 3: ADVANCED PRINTING Printing Multiple Pages on One Sheet of Paper (N-Up Printing) ..................................................... 18 Printing Posters ..................................................................................................................... 19 Printing a Reduced or Enlarged Document ................................................................................ 19 Fitting Your Document to a Selected Paper Size ......................................................................... 19 Using Watermarks ................................................................................................................. 20 Using an Existing Watermark ......................................................................................... 20 Creating a Watermark ................................................................................................... 20 Downloaded From ManualsPrinter.com Manuals
2 Editing a Watermark ..................................................................................................... 20 Deleting a Watermark ................................................................................................... 20 Using Overlays ...................................................................................................................... 21 What is an Overlay? ...................................................................................................... 21 Creating a New Page Overlay ......................................................................................... 21 Using a Page Overlay .................................................................................................... 21 Deleting a Page Overlay ................................................................................................ 21 Chapter 4: USING WINDOWS POSTSCRIPT DRIVER (SCX-4725FN ONLY) Printer Settings ..................................................................................................................... 22 Advanced .................................................................................................................. 22 Using Help ................................................................................................................... 22 Chapter 5: SHARING THE PRINTER LOCALLY Setting Up a Host Computer ................................................................................................... 23 Setting Up a Client Computer .................................................................................................. 23 Chapter 6: USING SMART PANEL Understanding Smart Panel .................................................................................................... 24 Opening the Troubleshooting Guide ......................................................................................... 24 Using Printer Settings Utility ................................................................................................... 25 Using Onscreen Help File ............................................................................................... 25 Changing the Smart Panel Program Settings ............................................................................. 25 Chapter 7: SCANNING Scanning Using Samsung SmarThru ......................................................................................... 26 Uninstalling Samsung SmarThru ..................................................................................... 26 Using Samsung SmarThru ............................................................................................. 27 Using Onscreen Help File ............................................................................................... 28 Scanning Process with TWAIN-enabled Software ........................................................................ 28 Scanning Using the WIA Driver ................................................................................................ 28 Downloaded From ManualsPrinter.com Manuals
3 Chapter 8: USING YOUR PRINTER IN LINUX Getting Started ..................................................................................................................... 29 Installing the Unified Linux Driver ............................................................................................ 29 Installing the Unified Linux Driver ................................................................................... 29 Uninstalling the Unified Linux Driver ............................................................................... 30 Using the Unified Driver Configurator ....................................................................................... 31 Opening the Unified Driver Configurator .......................................................................... 31 Printers Configuration ................................................................................................... 31 Scanners Configuration ................................................................................................. 32 Ports Configuration ....................................................................................................... 32 Configuring Printer Properties ................................................................................................. 33 Printing a Document .............................................................................................................. 33 Printing from Applications .............................................................................................. 33 Printing Files ................................................................................................................ 34 Scanning a Document ............................................................................................................ 34 Using the Image Manager .............................................................................................. 35 Chapter 9: USING YOUR PRINTER WITH A MACINTOSH (SCX-4725FN ONLY) Installing Software for Macintosh ............................................................................................. 37 Setting Up the Printer ............................................................................................................ 38 For a Network-connected Macintosh ................................................................................ 38 For a USB-connected Macintosh ..................................................................................... 38 Printing ................................................................................................................................ 39 Printing a Document ..................................................................................................... 39 Changing Printer Settings .............................................................................................. 39 Printing Multiple Pages on One Sheet of Paper .................................................................. 40 Scanning .............................................................................................................................. 41 Downloaded From ManualsPrinter.com Manuals