Samsung Idcs KeySet User Guide

ESTABLISHED CALL PICKUP [iDCS 500 L/LE VERSION]
To pick up an established call in progress at a single line extension con-
nected to a computer modem on your PC.
 Press the EPkey for that station on your keyset and the call is automat-
ically moved to your keyset.
 The single line extension on your modem will be disconnected.
NOTE: You must have an assigned (EP key) button on your regular keyset,
for the single line station.APPOINTMENT REMINDER/ALARM
CLOCKThis feature works like an alarm clock. Use it...

GROUP LISTENINGWhen you are engaged on a call and you are using the handset, you may
want other people to hear the distant party’s voice over the speaker:
 Press the LISTENkey to turn on the speaker. The microphone is not in
use, so the distant party does not hear other parties present in your of-
fice.
 Press LISTENagain to turn the speaker off and resume private conver-
sation.
 Repeat if necessary.
NOTE: Depending on speaker volume and the acoustics of your office, it
may be advisable to turn the...

When you receive an OHVA and secure OHVA is ON, you will hear the
announcement in the handset receiver, if you are using the handset. If
secure OHVA is OFF then you will hear the announcement on the speaker,
if you are talking on the handset. If you are using the speakerphone the
announcement will always be heard through the speaker.
To make an off-hook voice announcement:
 Dial the extension number or press the DSSkey.
 When you receive a busy signal, press the OHVAkey.
 After the attention tone,...

43
CUSTOMIZING YOUR KEYSET
AME PASSWORDThis feature allows people using the AME feature to enable password pro-
tection. This will prevent unauthorized people from listening to your mes-
sages being left. The passcode is the same as your station passcode. This
feature only applies if there is a CADENCE card installed in the system and
your keyset has a programmed AME key.
 With the handset on-hook, press TRANSFERand then dial 110.
 Dial 101to turn on AME PASSCODE or 100to turn it off.
 Press...

45 ing the C.O. line number, trunk group access code, intercom number or fea-
ture access code. To activate this feature:
 With the handset on-hook, press TRANSFERand then dial 110.
 Dial 031to turn the Hot Keypad on or 030to turn it off.
 Press TRANSFERto store your selection.
KEY CONFIRMATION TONEYou can hear a short beep (confirmation tone) each time you press a button
on the dial pad. This tone can be turned on or off.
 While on-hook, press TRANSFERand then dial 110.
 Dial 040to turn tones off...

47
DISPLAY FEATURES
INTERACTIVE DISPLAY KEYSThe three keys below the display are substitutes for dedicated feature keys
and access codes. Pressing one of these keys has the same effect as press-
ing a programmable key. These keys are called soft keys as their functions
are not fixed. They change to present you with the best options for that call
condition. The use of soft keys allows the programmable keys to be used for
more DSSand speed dial keys.
The SCROLLkey is used to display options available to...

CALL DURATION TIMERThe system can be set to automatically time outside calls. A few seconds
after you dial a telephone number, the timer appears in the display. It
appears immediately for incoming calls. The call timer continues for the du-
ration of the call. Call duration times are displayed in minutes and seconds.
If a call lasts longer than 60 minutes, the timer restarts.
You can press the TIMERkey to manually begin timing a call. Press it again
to stop timing. If you press it while the automatic...

PERSONAL SPEED DIAL NAMESEach personal speed dial number can have an 11 character name assigned
to it. This name is used to select the speed dial bin when you are dialing by
directory. 
 Press TRANSFERand then dial 106.
 Dial the speed dial bin number 00–49.
Write your message using the procedure described in 
Alarm Reminder
Messages
.
 Press the TRANSFERkey to store the speed dial name.
 Repeat for each speed dial bin if necessary.STATION NAMESYou can assign an 11 character name to your keyset....

53
TEXT MESSAGING 
[iDCS 500 L/LE VERSION ONLY]
This feature allows two digital keyset users to respond to each other with
preprogrammed messages. After receiving an Off Hook Voice
Announcement or Station Camp-On, you may respond with a text message
while continuing to talk and listen to your outside party. The other station
can view this message and take the appropriate action or respond back with
another text message.
There are 25 messages (01-25) stored in system memory that can be sent
to another...

55
Dial 205
205:busy
OHVA     CAMP ON
!
OHVA to 205 OHVA from 201
TMSG       REJECT
Wait for reply GIVE THE CALL
TMSG:01      SEND
Dial 03or press twice
ASK THEM TO HOLD
TMSG:03     SEND
!
ASK THEM TO HOLD Wait for reply
TMSG        EXIT
!
702:         01:45 701:         05:55
CONF   PAGE   MUTE  CONF   PAGE   MUTE
54
CALLER ID
WHAT IS CALLER ID?Caller ID is the name given to the telephone company-provided feature that
delivers the telephone number and sometimes the name of the person call-
ing your...