Samsung Idcs 100 Digital Communications System General Description Manual

2.11
iDCS 14B STRIP
(See Figure 2–20)
!14 programmable keys with red lights
!A maximum of one can be assigned to any iDCS
keyset to provide additional programmable keys
!Available in dark gray or light gray
FIGURE 2–20   

3.1
PART 3. SPECIFICATIONS
The following tables provide technical data for the iDCS 100 hybrid/key telephone systm.
3.1 ELECTRICAL SPECIFICATIONS
AC INPUT 112  (88–132) VAC (48–63 Hz)
POWER CONSUMPTION (MAX) 97 WATTS MAXIMUM FUSE RATING 5 AMP
BTU RATING (MAX) 5.5 BTU/MINUTE
DC OUTPUT +5 VOLTS 3.0 AMPS MAX
-5 VOLTS 0.5 AMPS MAX
-56 VOLTS 1.7 AMPS MAXIMUM
BATTERIES 10–40 AMPS 48 VOLTS
MAXIMUM CHARGE CURRENT 0.4 A
MAXIMUM DISCHARGE RATE 2.5 A
3.2DIMENSIONS AND WEIGHTS
HEIGHT WIDTH DEPTHWEIGHT
iDCS 100 BASIC...

3.2
3.3ENVIRONMENTAL LIMITS
OPERATING TEMPERATURE 32–104 °F/1–40 °C
STORAGE TEMPERATURE -13–158 °F/-10.5–70 °C
HUMIDITY 10%-90% NON-CONDENSING
3.4CABLE REQUIREMENTS
EQUIPMENTCABLE AWGMAX FEET MAX METERS
DIGITAL KEYSETS 1 PR. TWISTED 241300 400
ADD-ON MODULES 1 PR. TWISTED 241300 400
SINGLE LINE STATION 1 PR. TWISTED 243000 1 KM
DOOR PHONE 2 PR. TWISTED 24330* 100
*This is the maximum length of the cable between the door phone and the DPIM. The
DPIM can be installed up to 900 cable feet from the KSU....

3.3
SYSTEM TONES
Intercom Dial Tone—A steady tone that indicates you can begin dialing.
Ringback Tone—Indicates the station you dialed is ringing.
Busy Signal—Indicates the station you dialed is busy.
DND/No More Calls Tone—Fast busy tone advises you the station you dialed is in the Do Not Disturb
mode or cannot receive any more calls.
Transfer/Conference Tone—Indicates your call is being held and you can dial another party.
Confirmation Tone—Very short beeps followed by dial tone indicate you have...

3.4
3.6AKEYSET KEY LED INDICATIONS
CONDITIONLED COLOR LED ON LED  OFF
LINE IDLE OFF–OFF
LINE IN USE RED/GREENSTEADY–
RECALL AMBER 500 ms 500 ms
CALL ON HOLD RED/GREEN 500 ms 500 ms
RINGING C.O. CALL GREEN 100 ms 100 ms
RINGING INTERNAL CALL GREEN 100 ms 100 ms
DND INDICATION RED 112 IPM for 500 ms 500  ms
3.6BTERMINAL STATUS LED INDICATIONS
CONDITIONLED COLOR LED ON LED  OFF
BUSY / OFF HOOK REDSTEADY–
INTERCOM RING RED
400 ms ON / 200 ms OFF / 400 ms ON3 sec
OUTSIDE CALL RING GREEN 1 sec 3 sec
RECALL...

3.5
3.7ARESERVE POWER DURATION ESTIMATES (in minutes)*
     NO. OF UPS CAPACITY IN VOLT AMPS
 STATIONS250 400 450 600 900 1250 2000
4 65 160 200 245 360 490 930
8 45 110 135 160 240 320 625
12 40 90 115 140 200 280 535
16 30 75 90 110 160 220 415
24 25 50 70 85 120 175 380
32 20 45 60 75 100 150 330
40 15 35 50 60 80 125 275
48 10 20 45 50 55 75 100
56–10 30 45 50 60 80
*These are approximate values based on an idle system. The greater the C.O. line activity
on the system, the lower these readings will...

3.6
3.7BRESERVE POWER DURATION ESTIMATES
     NO. OF
 STATIONS                     WITHOUT SVMi                               WITH SVMi
8 83 Hours 57 Hours
16 49 Hours 39 Hours
24 35 Hours 29 Hours
32 27 Hours 23 Hours
40 22 Hours 18 Hours
48 17 Hours 11 Hours
The table above gives estimated system hold up times for a iDCS 100 system. These
times are based on an idle system equipped with a fully charged 40 Amp Hour / 48 Volt
battery pack. The hold up times stated above are approximate and will be reduced...

PART 4. BUSINESS FEATURE PACKAGE
SYSTEM FEATURES
4.1
Account Code Entry
Forced - Verified
Forced - Not Verified
Voluntary
Account Code Key
All Call Voice Page
Attention Tone
Authorization Codes
Forced
Voluntary
Auto Attendant†
Automatic Hold
Background Music
Call Activity Display
Caller Identification†
Automatic Number Identification (ANI)
Caller ID
Calling Line Identification (CLI)
Calling ID Features
Name/Number Display
Next Call
Save Caller ID Number
Store Caller ID Number
Inquire Park/Hold
Caller ID...

4.1 SYSTEM FEATURE DESCRIPTIONS
ACCOUNT CODE ENTRY
Station users may enter an account code (maximum 12 digits) before hanging up
from a call. This account code will appear in the SMDR printout for that call record.
Keyset users may enter this  code using an account code key without interrupting a
conversation. Single line telephone users must temporarily interrupt the call by
hook-flashing and dialing the feature access code. Manually entered account codes
can be up to 12 digits  long. In some cases...