Samsung Hp-p5091 Plasma Display Owners Instructions

1 
Remove the screws on the rear of the PDP panel.
2 
Connect insulation holders to screws (see the illustration below).
• If you are uncertain about installation, hire an Installation Specialist to install the 
wall mount bracket.
• Be sure to check that the insulation holders are completely secured on both the left
and right side after hanging the PDP on the wall mount bracket.
• Be careful to avoid getting your fingers caught during installation.
• Make sure the wall attachment panels are tightened....

32
1. Contact an authorized technician when installing the wall attachment panel.
2. After hanging the PDP panel on the wall attachment panel, make sure that the Insulation
holders are secure.
3. Be careful not to get your fingers caught during installation.
4. Make sure the wall attachment panel brackets are tightened. Otherwise, the PDP panel may 
fall down.
5. Please secure the mounting bracket on the wall surface after setting its angle at 0°.
How to Adjust Mounting Angle
Note  Note : Please secure...

PLASMA DISPLAY PANEL
with WIRELESS HOME AV CENTER
Operation
Turning the PDP On and Off ..........................................................34
Memorizing the Channels..............................................................35
Using the On-Screen Help ............................................................40
Setting your Favorite Channels ......................................................41
Fine Tuning Channels ....................................................................42...

34
Turning the PDP On and Off
Press the POWER ON button on the remote control. 
The PDP will be turned on and you will be ready to use its
features. You can also use the POWER ( ) button on the
front of the PDP. You can use the POWER ON button to turn
on the WIRELESS HOME AV CENTER. The WIRELESS
HOME AV CENTER and the PDP each have their own
respective POWER ON/OFF button, but when you turn off
the PDP, the WIRELESS HOME AV CENTER will turn off also.
Note 
•If your PDP isn’t turned on when the POWER ON...

35
Memorizing the Channels
Your PDP can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH and CH
buttons to scan through the channels. This eliminates the need to change channels by entering
the channel digits. There are three steps for memorizing channels: selecting a broadcast
source, memorizing the channels (automatic) and adding and deleting channels (manual).
Selecting the Video Signal-source...

36
Storing Channels in Memory (Automatic Method)
1
First, select the correct antenna (Air and Cable).
See steps on previous page. Press the MENU button.
Press the ▲or ▼ button to select “Channel”, 
then press the ENTER button. 
2
Press the ▲or ▼button to select “Auto Program”,
then press the ENTER button.
➤ ➤Quick way to access the Automatic Channel Setting: 
Just press the “AUTO PROG.” button on the remote control.
3
Press the ▲or ▼ button to select the correct signal 
(Air, STD, HRC, and IRC). Select...

37
Adding and Deleting Channels (Manual Method)
1 
Use the number buttons to directly select the channel
that will be added or deleted.
Ex) Channel “11”
2 
Press the ADD/DEL button, then press the ENTER 
button. Repeatedly pressing this button will alternate
between “Add” and “Delete”.
3 
Press the MENU button to exit.
Note
•You can view any channel (including an erased channel) by using the number buttons on the 
remote control.
Air  11
Press ENTER to delete the channelIn Memory
Add/Delete
Air 11
Mono...

38
Changing Channels
Using the Channel Buttons
Press the CH  or CH  button to change channels.
When you press the CH  or CH  button, the PDP changes 
channels in sequence. You will see all the channels that the PDP 
has memorized. (The PDP must have memorized at least three 
channels.) 
You will not see channels that were either erased or not memorized.
Directly Accessing Channels
Press the number buttons to go directly to a channel. For example, 
to select channel 27, press “2” then “7”. 
The TV will...

39
Adjusting the Volume
Using the Volume Buttons
Press the VOL or VOL  button to increase or decrease the 
volume. 
Using Mute
Using the MUTE Button
At any time, you can temporarily cut off the sound using the MUTE
button.
1
Press the MUTE button and the sound cuts off. 
2
The word “Mute” will appear in the lower-left 
corner of the screen.
3
To turn mute off, press the MUTE button again, 
or simply press the VOL  or VOL  button.
Mute 

40
To turn the on-screen help on :
1
Press the MENU button. Press the ▲or ▼button to 
select “Preference”, then press the ENTER button. 
2
Press the ▲or ▼button to select “Function Help”, 
then press the ENTER button. 
The on-screen help appears.
3
Press the ▲or ▼button to select “On” or “Off”.
Press the ▲or ▼button to highlight each of icons 
and read the description of the features that each 
icon represents.
4
Press the ENTER button. 
To turn the on-screen help off :
Press the ▲or ▼button to select...